Publication Cover
Journal of Environmental Science and Health, Part A
Toxic/Hazardous Substances and Environmental Engineering
Volume 37, 2002 - Issue 5
108
Views
14
CrossRef citations to date
0
Altmetric
Original Articles

METAL LEACHABILITY FROM SEWAGE SLUDGE-AMENDED THAI SOILS

, , &
Pages 765-791 | Received 30 Oct 2001, Published online: 06 Feb 2007
 

ABSTRACT

Determining mobility and availability of metals in sewage sludge amended soil is an environmental concern. Potential leachability and bioavailability of metals following sludge applied to agricultural soil was evaluated. Geochemical forms of metal occurring in sludge-amended soil were subjected to fractionation for understanding heavy metal transformation and remobilization in sludge-amended soil. Metal leachability was determined using reconstructed soil profiles where dewatered sewage sludge was incorporated into the surface 0–10 cm of soil. Two-sludge application rates; 150 and 300 kgN/ha, equivalent to sludge at 4 and 8 ton/ha, were applied to soil columns representing typical agricultural clay soils of Thailand (Rangsit acid sulfate soil). The soil columns were leached with 32 l equivalent to 600 mm of surface water using different leachants (distilled water pH 6, distilled water adjusted to pH 3 and rainwater pH 5). Among metals measurement, results showed Mn leachability from sludge-amended Rangsit soil were high at both sludge application rates (18–29% of total Mn applied). The leachability of other metals was less than 2.5 and 7.2% following application of 150 and 300 kgN/ha of sludge, respectively. Results from the experiments indicated that the leachant at pH 3 had the most effect on potential leachability of Cu, Zn, Cd, and Ni, except Fe and Mn, at low sludge application rate. Whereas, only the leachability of two metals was influenced by the lowest pH (pH 3) when sludge applied was increased. Besides pH of leachant, it appeared that leachability of elements from the soil column depended on rate of sludge applied, the particular metal, and metal form or fraction. The soil studied had organic matter, CEC, pH, clay content, etc., that resulted in high buffering capacity, which favors metal retention. Less than 0.5 and 1.8% of the added Cu and Zn applied at the 150 and 300 kgN/ha application rates, respectively, were detected in the leachate. Approximately 100% of the added Cu and Zn in the sludge remained in the surface 10 cm at each sludge application rate. Sequential extraction of sludge-amended soil following leaching (at the high sludge application rate) revealed that most of the Cu remained in the surface sludge-amended soil layer (0–2 cm depth) in the form of organic and residual Cu fractions that are not easily mobilized. An exchangeable fraction of Zn increased, approximately representing 60% total Zn applied in sludge–soil layer as compared with its native soil Zn fractions. These results demonstrate that Zn availability in the soil would increase as a result of sludge application. However, the total Zn in the leachate is safe for agricultural use, because it represents an amount of less than 2% of total Zn applied.

ACKNOWLEDGMENTS

The author would like to thank Mr. Somchai Sornwanee, Ms. Jarirat Srinatpat, and Ms. Noppawan Jantavee for their excellent technical support and assistance on sample analyses throughout the experiment at the Department of Drainage and Sewerage, Bangkok Metropolitan Administration (BMA). The Royal Thai Government provided the financial support for this research.

Reprints and Corporate Permissions

Please note: Selecting permissions does not provide access to the full text of the article, please see our help page How do I view content?

To request a reprint or corporate permissions for this article, please click on the relevant link below:

Academic Permissions

Please note: Selecting permissions does not provide access to the full text of the article, please see our help page How do I view content?

Obtain permissions instantly via Rightslink by clicking on the button below:

If you are unable to obtain permissions via Rightslink, please complete and submit this Permissions form. For more information, please visit our Permissions help page.