112
Views
1
CrossRef citations to date
0
Altmetric
Articles

Locations of strain gauges for fatigue analysis of welded joints (1)

Pages 559-566 | Published online: 18 Oct 2011
 

Notes

1. Fatigue assessment is assured either by damage-tolerant design or safe-life design. γM is a partial safety coefficient of fatigue resistance related to stress, used in safe-life design. In this advice, there are no general recommendations but in safe-life design, it is 1.15 when γM causes damage to a secondary member, an effect that causes damage for some part (or structure), 1.30 when the damage is to the entire structure and 1.40 when the damage is to human life. When a structural member is produced at usual quality, and it is inspected regularly during use, γM = 1 is appropriate1.

The maximum value for Δσs,d in the 1995 edition is 26 MPa for steel and 10 MPa for aluminium alloy, in each case lower than the 1996 edition.

2. The value m used in the formula N = K/Δσm of the S − N curve for nominal stress is m 1 = 3.0 when number of iterations N < 5 ⊆ 106 and m 2 = 5.0 when number of iterations N≦5 ⊆ 106, with N = 108 being the cut-off. When this is used in cumulative damage calculation, recent research indicates that assessments that use this formula are rather unstable and, in order to avoid this problem as far as possible, the sum of the minor side should not be 1 m, as is usual, but 0.5, as shown below:

3. FAT is the stress range (N/mm2) at N = 2 ⊆ 106 iterations of the design S − N curve. For an explanation of the S − N curve, etc. for aluminium alloys, see Reference 6.

4. For example, in the IIW recommendations1, there are allowable values for some transverse butt joints and load transmitting cruciform joints; for example, the allowable quantity for misalignment of the latter is less than 15% of sheet thickness.

5. For the stress concentration factors due to these misalignments, see, for example, Refs 7 and 8.

6. The materials used, according to the IIW recommendations1, are structural steel with ferrite/pearlite microstructure or bainite microstructure and aluminium alloys used in welding structures, up to yield strength σy≦700 MPa. The EC 3 standards2 are for structural stainless steel and uncoated weather-resistant steel. The EC 9 standards3 are for 7020 alloy and 5000 and 6000 aluminium alloys.

7. Usually, electrical resistance wire strain gauges are used for stress concentration measurement in experimental stress analysis. The gauge length should preferably be short and 0.4 mm is recommended. A two-strand or three-strand strain gauge is used according to measure the structure depending on the stress state but details are omitted here.

The parts where they are used are as follows:4

(1) Measurement of nominal stress of a structure at a location distant from the structural discontinuity, that is, other than the region of the geometric stress concentration is by an appropriately located strain gauge with the result that this is separated into axial force, bending moment, shear force and torsion, etc.

(2) Geometric strain measurement to determine the hotspot stress for local discontinuities in a structural component.

(3) The same as the above but in this case measurement to establish the hotspot S − N curve for the fatigue specimen.

(4) Studies of dynamic response of a structure to evaluate the actual dynamic load coefficient used in stress calculation.

(5) Verification of the results obtained by FEM; this comparison is one of the conditions used in the hotspot stress approach.

(6) Experimental determination of the geometric stress concentration using (1) and (2) above.

(7) Recording of the stress history of either (1) or (2) above, to obtain data on the stress generated in structural components subjected to variable amplitude loading.

Log in via your institution

Log in to Taylor & Francis Online

PDF download + Online access

  • 48 hours access to article PDF & online version
  • Article PDF can be downloaded
  • Article PDF can be printed
USD 61.00 Add to cart

Issue Purchase

  • 30 days online access to complete issue
  • Article PDFs can be downloaded
  • Article PDFs can be printed
USD 726.00 Add to cart

* Local tax will be added as applicable

Related Research

People also read lists articles that other readers of this article have read.

Recommended articles lists articles that we recommend and is powered by our AI driven recommendation engine.

Cited by lists all citing articles based on Crossref citations.
Articles with the Crossref icon will open in a new tab.