References
- Hamidi MFFA, Harun WSW, Samykano M, et al. A review of biocompatible metal injection moulding process parameters for biomedical applications. Mater Sci Eng C. 2017;78:1263–1276. doi: 10.1016/j.msec.2017.05.016
- Hnatkova E, Hausnerova B, Hales A, et al. Processing of MIM feedstocks nased on inconel 718 powder and partially water-soluble binder varying in PEG molecular weight. Powder Technol. 2017;322:439–446. doi: 10.1016/j.powtec.2017.09.029
- Hidalgo J, Fernandez JP, Jimenez-Morales A, et al. Effect of the particle size and solids volume fraction on the thermal degradation behaviour of invar 36 feedstock. Polym Degrad Stab. 2013;98(12):2546–2555. doi: 10.1016/j.polymdegradstab.2013.09.015
- Royer A, Barriere T, Gelin JC. The degradation of poly(ethylene glycol) in an Inconel 718 feedstock in metal injection molding process. Powder Technol. 2015;284:467–474. doi: 10.1016/j.powtec.2015.07.032
- Dehghan-Manshadi A, Bermingham M, Dargusch MS, et al. Metal injection moulding of titanium and titanium alloys: challenges and recent development. Powder Technol. 2017;319:289–301. doi: 10.1016/j.powtec.2017.06.053
- Dimitri C, Mohamed S, Thierry B, et al. Influence of particle-size distribution and temperature on the rheological properties of highly concentrated Inconel feedstock alloy 718. Powder Technol. 2017;322: 273–289. doi: 10.1016/j.powtec.2017.08.049
- Zhang L, Chen X, Li D, et al. A comparative investigation on MIM418 superalloy fabricated using gas- and water-atomized powders. Powder Technol. 2015;286:798–806. doi: 10.1016/j.powtec.2015.09.023
- Djoudi H, Gelin JC, Barriere T. Experiments and FE simulation for twin screw mixing of nanocomposite of polypropylene/multi-walled carbon nanotubes. Compos Sci Technol. 2015;107:169–176. doi: 10.1016/j.compscitech.2014.12.017
- Barriere T, Gelin JC, Liu B. Improving mould design and injection parameters in metal injection moulding by accurate 3D finite element simulation. J Mater Process Technol. 2002;125-126(126):518–524. doi: 10.1016/S0924-0136(02)00307-2
- Dvorak P, Barriere T, Gelin JC. Direct observation of mould cavity filling in ceramic injection moulding. J Eur Ceram Soc. 2008;28:1923–1929. doi: 10.1016/j.jeurceramsoc.2008.02.001
- Belgacem M, Barriere T, Gelin J-C. Investigations on thermal debinding process for fine 316L stainless steel feedstocks and identification of kinetic parameters from coupling experiments and finite element simulations. Powder Technol. 2013;235:192–202. doi: 10.1016/j.powtec.2012.10.006
- Ou H, Sahli M, Gelin JC, et al. Experimental analysis and finite element simulation of the co-sintering of bi-material components. Powder Technol. 2014;268:269–278. doi: 10.1016/j.powtec.2014.08.023
- Song J, Gelin JC, Barriere T, et al. Experiments and numerical modelling of solid state sintering for 316L stainless steel components. J Mater Process Technol. 2006;177:352–355. doi: 10.1016/j.jmatprotec.2006.04.111
- Bordia RK, Scherer GW. On constrained sintering - I. Constitutive model for a sintering body. Acta Metall. 1988;36:2393–2397. doi: 10.1016/0001-6160(88)90189-7
- Bordia RK, Scherer GW. On constrained sintering - II. Comparison of constitutive models. Acta Metall. 1988;36:2399–2409. doi: 10.1016/0001-6160(88)90190-3
- Riedel H, Zipse H, Svoboda J. Equilibrium pore surface, sintering stresses and constitutive equations for the intermediate and late stages of sintering - II. Diffusional densification and creep. Acta Metall Mater. 1994;42(2):445–452. doi: 10.1016/0956-7151(94)90499-5
- Royer A, Barriere T, Bienvenu Y. Influence of supercritical debinding and processing parameters on final properties of injection-moulded Inconel 718. Powder Technol. 2018;336:311–317. doi: 10.1016/j.powtec.2018.05.047
- Song J, Barriere T, Liu B, et al. Experimental and numerical analysis on the sintering behaviours of injection moulded components in 316L stainless steel powder. Powder Metall. 2010;53(4):295–304. doi: 10.1179/003258908X334212
- Sahli M, Mamen B, Ou H, et al. Experimental analysis and numerical simulation of sintered micro-fluidic devices using powder hot embossing process. Int J Adv Manuf Technol. 2018;99(5-8):1141–1154. doi: 10.1007/s00170-018-2509-5
- Sahli M, Gelin JC, Barriere T. Replication of microchannel structures in WC-Co feedstock using elastomeric replica moulds by hot embossing process. Mater Sci Eng C. 2015;55:252–266. doi: 10.1016/j.msec.2015.05.019