References
- Heaney DF. Handbook of metal injection molding. Cambridge: Woodhead Publishing; 2012.
- Raza MR, Sulong AB, Muhamad N, et al. Effects of binder system and processing parameters on formability of porous Ti/HA composite through powder injection molding. Mater Des. 2015;87:386–392.
- Oh JW, Lee WS, Park SJ. Influence of nano powder on rheological behavior of bimodal feedstock in powder injection molding. Powder Technol. 2017;311:18–24.
- Keshavarz Panahi A, Mianajiy H, Miandoabchi E, et al. Optimization of the powder injection molding process parameters using the sequential simplex algorithm and sensitivity analysis. J Manuf Sci Eng Trans ASME. 2013;135(1): 011006-1–011006-7
- Binet C, Heaney DF, Spina R, et al. Experimental and numerical analysis of metal injection molded products. J Mater Process Technol. 2005;164-165:1160–1166.
- Bilovol VV, Kowalski L, Duszczyk J, et al. The effect of constitutive description of PIM feedstock viscosity in numerical analysis of the powder injection moulding process. J Mater Process Technol. 2006;178(1-3):194–199.
- Kate KH, Enneti RK, Onbattuvelli VP, et al. Feedstock properties and injection molding simulations of bimodal mixtures of nanoscale and microscale aluminum nitride. Ceram Int. 2013;39(6):6887–6897.
- Zheng ZS, Qu XH. Numerical simulation of powder injection moulding filling process for intricate parts. Powder Metall. 2006;49(2):167–172.
- Zheng Z-X, Xia W, Zhou Z-Y, et al. Numerical simulation of tungsten alloy in powder injection molding process. Trans. Nonferrous Met Soc China (English Ed). 2008;18(5):1209–1215.
- Bilovol VV, Kowalski L, Duszczyk J, et al. Comparison of numerical codes for simulation of powder injection moulding. Powder Metall. 2003;46(1):55–60.
- Dongguo L, Tae Gon K, Jun Sae H, et al. Experimental and numerical analysis of injection molding of Ti–6Al–4V powders for high-performance titanium parts. JOM. 2018;70(5):621–625.
- Feng S, Bin Q, Yan-feng D, et al. Simulation on the two-phase separation of powder injection molding 316L stainless steel. Mater Sci. 2019;25(3):246–251.
- Ahn S, Chung ST, Atre SV, et al. Integrated filling, packing and cooling CAE analysis of powder injection moulding parts. Powder Metall. 2008;51(4):318–326.
- Sardarian M, Mirzaee O, Habibolahzadeh A. Influence of injection temperature and pressure on the properties of alumina parts fabricated by low pressure injection molding (LPIM). Ceram Int. 2017;43(6):4785–4793.
- Zhang M, Lin B. Simulation of ceramic injection molding for zirconia optical ferrule. Key Eng Mater. 2007;336–338:997–100.
- Sardarian M, Mirzaee O, Habibolahzadeh A. Mold filling simulation of low-pressure injection molding (LPIM) of alumina: effect of temperature and pressure. Ceram Int. 2017;43(1):28–34.
- Sardarian M, Mirzaee O, Habibolahzadeh A. Numerical simulation and experimental investigation on jetting phenomenon in low-pressure injection molding (LPIM) of alumina. J Mater Process Technol. 2017;243:374–380.
- Hausnerova B, Mukund BN, Sanetrnik D. Rheological properties of gas and water atomized 17-4PH stainless steel MIM feedstocks: effect of powder shape and size. Powder Technol. 2017;312:152–158.
- Lin D, Sanetrnik D, Cho H, et al. Rheological and thermal debinding properties of blended elemental Ti–6Al–4V powder injection molding feedstock. Powder Technol. 2017;311:357–363.
- Feng H, Wei L, Zhipeng X. Surface modification of alumina powder particles through stearic acid for the fabrication of translucent alumina ceramics by injection molding. Ceram Int. 2016;42(14):16274–16280.
- Standring T, Blackburn S, Wilson P. Investigation into paraffin wax and ethylene vinyl acetate blends for use as a carrier vehicle in ceramic injection molding. Polymer Plastics Technol Eng. 2016;55(8):802–817.
- Rei M, Milke EC, Gomes RM, et al. Low-pressure injection molding processing of a 316-L stainless steel feedstock. Mater Lett. 2002;52(4-5):360–365.
- Goncalves AC. Metallic powder injection molding using low pressure. J Mater Process Technol. 2001;118:193–198.
- ATSM Int. ASTM-E1269: standard test method for determining specific heat capacity by differential scanning calorimetry. West Conshohocken (PA): ASTM Int.; 2018.
- Borup KA, De Boor J, Wang H, et al. Measuring thermoelectric transport properties of materials. Energy Environ Sci. 2015;8(2):423–435.