Reference
- Ananthapadmanaban D, Rao VS, Abraham N, et al. A study of mechanical properties of friction welded mild steel to stainless steel joints. Mater Des. 2009;30:2642–2646.
- Li P, Li JL, Li X, et al. A study of the mechanisms involved in initial friction process of continuous drive friction welding. J Adhes Sci Technol. 2015;29:1246–1257.
- Seli H, Ismail AIM, Rachman E, et al. Mechanical evaluation and thermal modelling of friction welding of mild steel and aluminium. J Mater Process Technol. 2010;210:1209–1216.
- Li WY, Vairis A, Preuss M, et al. Linear and rotary friction welding review. Int Mater Rev. 2016;61:71–100.
- Xiong JT, Li JL, Wei YN, et al. An analytical model of steady-state continuous drive friction welding. Acta Mater. 2013;61:1662–1675.
- Midling OT, Grong O. A process model for friction welding of Al- Mg-Si alloys and Al-SiC metal matrix composites—I. Haz temperature and strain rate distribution. Acta Mater. 1994;42:1595–1609.
- Zhang QZ, Zhang LW, Liu WW, et al. 3D rigid viscoplastic FE modelling of continuous drive friction welding process. Sci Technol Weld Join. 2006;11:737–743.
- Maalekian M. Thermal modeling of friction welding. ISIJ Int. 2008;48:1429–1433.
- Zhao PK, Fu L, Zhong DC. Numerical simulation of transient temperature and axial deformation during linear friction welding between TC11 and TC17 titanium alloys. Comput Mater Sci. 2014;92:325–333.
- Kozlowski PF, Thomas BG, Azzi JA, et al. Simple constitutive equations for steel at high temperature. MTA. 1992;23:903–918.
- Ma X, Zeng WD, Sun Y, et al. Modeling constitutive relationship of Ti17 titanium alloy with lamellar starting microstructure. Mater Sci Eng A. 2012;538:182–189.
- Zhang XM, Cao FY, Yue HY, et al. Establishment of constitutive equations of TC11 alloy during hot deformation. Rare Metal Mat Eng. 2013;42:937–941.
- Bagheripoor M, Bisadi H. Application of artificial neural networks for the prediction of roll force and roll torque in hot strip rolling process. Appl Math Model. 2013;37:4593–4607.
- Li WY, Wang FF. Modeling of continuous drive friction welding of mild steel. Sci Eng A-Struct. 2011;528:5921–5926.
- Schmidt H, Hattel J, Wert J. An analytical model for the heat generation in friction stir welding. Modelling Simul Mater Sci Eng. 2004;12:143.
- Sheppard T, Jackson A. Constitutive equations for use in prediction of flow stress during extrusion of aluminium alloys. Mats Sci Tech. 1997;13:203–209.
- Li WY, Ma TJ, Li JL. Numerical simulation of linear friction welding of titanium alloy: effects of processing parameters. Mater Des. 2010;31:1497–1507.
- Bruschi S, Poggio S, Quadrini F, et al. Workability of Ti–6Al–4V alloy at high temperatures and strain rates. Mater Lett. 2004;58:3622–3629.
- Heidarzadeh A. Tensile behavior, microstructure, and substructure of the friction stir welded 70/30 brass joints: RSM, EBSD, and TEM study. Arch Civ Mech Eng. 2019;19:137–146.
- Heidarzadeh A, Barenji RV, Khalili V, et al. Optimizing the friction stir welding of the α/β brass plates to obtain the highest strength and elongation. Vacuum. 2019;159:152–160.
- Heidarzadeh A, Saeid T, Klemm V, et al. Effect of stacking fault energy on the restoration mechanisms and mechanical properties of friction stir welded copper alloys. Mater Des. 2019;162:185–197.
- Heidarzadeh A, Khodaverdizadeh H, Mahmoudi A, et al. Tensile behavior of friction stir welded AA 6061-T4 aluminum alloy joints[J]. Mater Des. 2012;37:166–173.
- Heidarzadeh A, Motalleb-Nejad P, Barenji RV, et al. The origin of the maximum hardness of the friction stir welded single-phase Cu-Zn plates: RSM, EBSD, and TEM investigation. Mater Chem Phys. 2019;223:9–15.
- Amiri M, Khonsari MM. On the thermodynamics of friction and wear—a review. Entropy. 2010;12:1021–1049.
- Prasad Y, Seshacharyulu T. Modelling of hot deformation for microstructural control. Int Mat Rev. 1998;43:243–258.
- Lorenz R. Computational mathematics. Full steam ahead-probably. Science. 2003;299:837–888.
- Martyushev LM, Seleznev VD. Maximum entropy production principle in physics, chemistry and biology. Phy Rep. 2006;426:1–45.
- Nevin PK. Steady state of a dissipative flow-controlled system and the maximum entropy production principle. Phy Rev. 2009;80:021113.
- Aghdam AB, Khonsari MM. Application of a thermodynamically based wear estimation methodology. J Tribol. 2016;138:041601.
- Song Y, Dai Z, Xue Q. Entropy generation related to plastic deformation in fretting friction. Wear. 2014;315:42–50.
- Cai J, Li FG, Liu TY, et al. Constitutive equations for elevated temperature flow stress of Ti–6Al–4V alloy considering the effect of strain. Mater Des. 2011;32:1144–1151.
- Kimura M, Kusaka M, Seo K, et al. Effect of inner diameter on friction torque in the friction welding of tubes[J]. Weld Inter. 2005;19:272–278.
- Kimura M, Ichihara A, Kusaka M, et al. Joint properties and their improvement of AISI 310S austenitic stainless steel thin walled circular tube friction welded joint. Mater Des. 2012;38:38–46.
- Qian JW. PhD thesis, Study on the mechanism of heat generation and construction of analytical model for friction welding (in Chinese). Xi'an PRC: Northwestern Polytechnical University; 2005.