References
- Gürgen S. A parametric investigation of roller hemming operation on a curved edge part. Arch Civ Mech Eng. 2019;19(1):11–19.
- Moura MFSF, Gonçalves JPM, Chousal JAG, et al. Cohesive and continuum mixed-mode damage models applied to the simulation of the mechanical behaviour of bonded joints. Int J Adhes Adhes. 2008;28(8):419–426.
- Banea MD, Rosioara M, Carbas RJC, et al. Multi-material adhesive joints for automotive industry. Compos Part B-Eng. 2018;151:71–77.
- Watson B, Nandwani Y, Worswick MJ, et al. Metallic multi-material adhesive joint testing and modeling for vehicle lightweighting. Int J Adhes Adhes. 2019;95:102421.
- Ma C, Tian Y, Gong Y, et al. Study of the effect of curing residual stress on the bonding strength of the single lap joint using a high-temperature phosphate adhesive. Materials. 2018;11(7):1198.
- Viana G, Machado J, Carbas R, et al. Strain rate dependence of adhesive joints for the automotive industry at low and high temperatures. J Adhes Sci Technol. 2018;32(19):2162–2179.
- Salih A, Iclal AA. Effect of nanostructured reinforcement of adhesive on thermal cycling performance of a single-lap joint with composite adherends. Compos Part B- Eng. 2019;175:107106.
- Radka B, Tomas B, Jiri S, et al. The influence of temperature and cyclic loading on adhesion in polycarbonate-polyurethane-glass adhesive joint. J Adhes Sci Technol. 2019;33(13):1381–1393.
- Paroissien E, Silva LFM, Lachaud F. Simplified stress analysis of functionally graded single-lap joints subjected to combined thermal and mechanical loads. Compos Struct. 2018;203:85–100.
- Andersson A. Evaluation and visualisation of surface defects on auto-body panels. J Mater Process Technol. 2009;209(2):821–837.
- Wu X, Hao H, Zhang G, et al. Variation in autobody adhesive curing process. SAE Technol. 1999;01:0997.
- Basu SK, Kia HG. Theoretical modeling of bond-line read-out in adhesive joined smc automotive body panels. J Compos Mater. 2008;42(6):539–552.
- Patankar KA, Dillard DA, Fernholz KD. Characterizing the constitutive properties and developing a stress model for adhesive bond-line readout. Int J Adhes Adhes. 2013;40:149–157.
- Zhu X, Li Y, Ni J, et al. Curing-induced debonding and its influence on strength of adhesively bonded dissimilar material joints. J Manuf Sci E-T ASME. 2016;138:061005.
- Zhu X, Li Y, Chen G, et al. Curing-induced distortion mechanism in adhesive bonding of aluminum AA6061-t6 and steels. J Manuf Sci E-T ASME. 2013;135:051007.
- Her S, Min C. Adhesively bonded patch repair of composite laminates. J Adhes Sci Technol. 2011; 25(18):2569–2585.
- Fuchs H, Fernholz KD, Deslauriers P. Predicted and measured bond-line read-through response in composite automotive body panels subjected to elevated temperature cure. J Adhes. 2010;86(10):982–1011.
- Hojjati M, Johnston AA, Hoa SV, et al. Viscoelastic behavior of cytec fm73 adhesive during cure. J Appl Polym Sci. 2004;91(4):2548–2557.
- Crocombe AD, Yu XX, Richardson G. A unified visco-plastic model for the stress analysis of adhesively bonded structures. J Adhes Sci Technol. 2001;15(3):279–302.
- Hahn O, Jendrny J. Evaluation of simulation models for the estimation of deformation of adhesively bonded steel sheets during curing. Weld World. 2003;47(7-8):31–38.
- Priesnitz K, Sinke J, Benedictus R. Influence of the temperature cycle on local distortions in car panels caused by hot curing epoxies. Int J Adhes Adhes. 2014;50:216–222.
- Singer G, Sinn G, Lichtenegger HC, et al. Evaluation of in-situ shrinkage and expansion properties of polymer composite materials for adhesive anchor systems by a novel approach based on digital image correlation. Polym Test. 2019;79:106035.
- Fernholz KD, Wykoff R. Impact of cooling method and incoming sheet quality on final part surface quality in thick sheet paint film thermoformed parts. Polym Eng Sci. 2009;49(1):137–147.
- Li Y, Wang SN, Guo YM, et al. Lowering curing temperature in adhesive bonding of aluminum AA6061-T4. J Adhesion. 2018;94(11):893–909.
- Zhang JT, Zhang M, Li SX, et al. Residual stresses created during curing of a polymer matrix composite using a viscoelastic model. Compos Sci Technol. 2016;130:20–27.
- Ding A, Li S, Sun J, et al. A thermo-viscoelastic model of process-induced residual stresses in composite structures with considering thermal dependence. Compos Struct. 2016;136:34–43.
- Mohammad S, Arash R. The effect of viscoelasticity of adhesives on shear stress distribution in a double-lap joint using analytical method. J Adhes Sci Technol. 2013;27(20):2233–2250.
- Bálint F, Goda TJ. Numerical stress solutions for the accurate calibration of hyper-viscoelastic material models of polymer foams. Int J Solids Struct. 2020;191:390–400.
- Wang Z, Li P. Visco-elasto-plastic constitutive model of adhesives under uniaxial compression in a range of strain rates. J Appl Polym Sci. 2020;137(33):48962.
- Adolf D, Martin JE, Chambers R, et al. Stresses during thermoset cure. J Mater Res. 1998;13(3):530–550.
- Priesnitz K, Sinke J, Benedictus R. On the simulation of panel distortions due to hot curing adhesives. Int J Solids Struct. 2014;51(13):2470–2478.
- Jansen K, Vreugd J, Ernst L. Analytical estimate for curing-induced stress and warpage in coating layers. J Appl Polym Sci. 2012;126(5):1623–1630.
- Vreugd J, Jansen K, Ernst L, et al. Prediction of cure induced warpage of micro-electronic products. Microelectron Reliab. 2010;50(7):910–916.
- Hu P, Han X. Influence of automobile body coating process on the strength of unbalanced adhesive joints. JME. 2012;48(20):93–102.
- Sang YP, Won JC, Chi HC, et al. The effect of curing temperature on thermal, physical and mechanical characteristics of two types of adhesives for aerospace structures. J Adhes Sci Technol. 2018;32(11):1200–1223.
- Málek J. The kinetic analysis of non-isothermal data. Thermochimi Acta. 1992;200:257–269.
- Header H, Kobaisi MA. Influence of moisture content on the thermal and mechanical properties and curing behavior of polymeric matrix and polymer concrete composite. Mater Des. 2013;49:850–856.
- Sun W, Vassilopoulos AP, Keller T. Effect of thermal lag on glass transition temperature of polymers measured by DMA. Int J Adhes Adhes. 2014;52:31–39.
- Lei H, Frazier CE. A dynamic mechanical analysis method for predicting the curing behavior of phenol-formaldehyde resin adhesive. J Adhes Sci Technol. 2015;29(10):981–990.
- Martínez-Miranda MR, García-Martínez V, Gude MR. Gel point determination of a thermoset prepreg by means of rheology. Polym Test. 2019;78:105950.
- Chakravorty S. PVT testing of polymers under industrial processing conditions. Polym Test. 2002;21(3):313–317.
- Nawab Y, Casari P, Boyard N, et al. Characterization of the cure shrinkage, reaction kinetics, bulk modulus and thermal conductivity of thermoset resin from a single experiment. J Mater Sci. 2013;48(6):2394–2403.
- Emri I, Prodan TA. Measuring system for bulk and shear characterization of polymers. Exp Mech. 2006;46(4):429–439.
- Mather PT, White SR. Viscoelastic properties of an epoxy resin during cure. J Compos Mater. 2001;35(10):121–123.
- Jairaja R, Narayana N. Strengthening of the adhesive bond using a mixture of adhesives between dissimilar adherends in a single lap joint. J Adhes Sci Technol. 2020;34(6):579–598.