On post-fire bond strength of steel rebar embedded in thermally-damaged concrete – a review

References

• Thanaraj DP, Anand N, Prince Arulraj G, et al. Post-fire damage assessment and capacity based modeling of concrete exposed to elevated temperature. Int J Damage Mech. 2020;29(5):748–779.
   Web of Science ®Google Scholar
• Patnaik B, Bhojaraju C, Mousavi SS. Experimental study on residual properties of thermally damaged steel fiber-reinforced concrete containing copper slag as fine aggregate. J Mater Cycles Waste Manag. 2020;22(3):801–815.
   Web of Science ®Google Scholar
• Ahmed A, Al-Shaikh A, Arafat T. Residual compressive and bond strengths of limestone aggregate concrete subjected to elevated temperatures. Mag Concr Res. 1992;44(159):117–125.
   Web of Science ®Google Scholar
• Pei P, Zheng S, Zhang Y, et al. Overview on the bonding of reinforced concrete under pristine, corrosive and freeze-thaw conditions. J Adhes Sci Technol. 2019;33(7):761–789.
   Web of Science ®Google Scholar
• Mousavi S, Dehestani M, Mousavi K. Bond strength and development length of steel bar in unconfined self-consolidating concrete. Eng Struct. 2017;131:587–598.
   Web of Science ®Google Scholar
• Mousavi S, Dehestani M, Mousavi S. Bond strength and development length of glass fiber-reinforced polymer bar in unconfined self-consolidating concrete. J Reinf Plast Compos. 2016;35(11):924–941.
   Web of Science ®Google Scholar
• Mousavi SS, Guizani L, Ouellet-Plamondon CM. Simplified analytical model for interfacial bond strength of deformed steel rebars embedded in pre-cracked concrete. J Struct Eng. 2020;146(8):04020142.
   Web of Science ®Google Scholar
• Mousavi SS, Guizani L, Ouellet-Plamondon CM. On bond-slip response and development length of steel bars in pre-cracked concrete. Constr Build Mater. 2019;199:560–573.
   Web of Science ®Google Scholar
• Pokorný P, Tej P, Kouřil M. Evaluation of the impact of corrosion of hot-dip galvanized reinforcement on bond strength with concrete–a review. Constr Build Mater. 2017;132:271–289.
   Web of Science ®Google Scholar
• Lin H, Zhao Y, Feng P, et al. State-of-the-art review on the bond properties of corroded reinforcing steel bar. Constr Build Mater. 2019;213:216–233.
   Web of Science ®Google Scholar
• Mousavi SS, Mousavi Ajarostaghi SS, Bhojaraju C. A critical review of the effect of concrete composition on rebar–concrete interface (RCI) bond strength: a case study of nanoparticles. SN Appl Sci. 2020;2(5):893.
   Web of Science ®Google Scholar
• Milovanov A, Pryadko V. Bond reinforcement to refractory (fire-resistant) concretes at high temperatures, in foreign literature study no. 440, skokie, Illinois (translated from beton in zhelezobeton. Skokie (IL): Portland Cement Association; 1963. p. 215–219.
   Google Scholar
• Bushev VS, Pchelintsev VA, Fedorenko VS, et al. Fire resistance of buildings. 1st ed. Boston (MA): National Lending Library for Science and Technology; 1966.
   Google Scholar
• Ghahramani A, Sabzevari A. Studies on reduction of bond in reinforced concrete due to heat cycle. Coimbatore (India): College of Technology Coimbatore; 1969.
   Google Scholar
• Harada T, et al. Strength, elasticity and thermal properties of concrete subjected to elevated temperatures. Special Publication. 1972;34:377–406.
   Google Scholar
• Reichel V. How fire affects steel-to-concrete bond. Batiment Int Build Res Pract. 1978;6(3):176–176.
   Google Scholar
• Royles R, Morley P. Further responses of the bond in reinforced concrete to high temperatures. Mag Concr Res. 1983;35(124):157–163.
   Web of Science ®Google Scholar
• Morley P, Royles R. Response of the bond in reinforced concrete to high temperatures. Mag Concr Res. 1983;35(123):67–74.
   Web of Science ®Google Scholar
• Rostásy FS, Sager H. Hochtemperaturverbundverhalten von Beton-und Spannstählen. Braunschweig (Germany): Technische Universität Braunschweig; 1985.
   Google Scholar
• Chiang C-H, Tsai C-L. Time–temperature analysis of bond strength of a rebar after fire exposure. Cem Concr Res. 2003;33(10):1651–1654.
   Web of Science ®Google Scholar
• Haddad RH, Ra’ed MA. Effect of thermal cycling on bond between reinforcement and fiber reinforced concrete. Cem Concr Compos. 2004;26(6):743–752.
   Web of Science ®Google Scholar
• Haddad RH, Shannis LG. Post-fire behavior of bond between high strength pozzolanic concrete and reinforcing steel. Constr Build Mater. 2004;18(6):425–435.
   Web of Science ®Google Scholar
• Tanyildizi H, Coskun A, Somunkiran I. An experimental investigation of bond and compressive strength of concrete with mineral admixtures at high temperatures. Arab J Sci Eng. 2008;33(2):443.
   Google Scholar
• Haddad RH, Al-Saleh RJ, Al-Akhras NM. Effect of elevated temperature on bond between steel reinforcement and fiber reinforced concrete. Fire Saf J. 2008;43(5):334–343.
   Web of Science ®Google Scholar
• Bingöl AF, Gül R. Residual bond strength between steel bars and concrete after elevated temperatures. Fire Saf J. 2009;44(6):854–859.
   Web of Science ®Google Scholar
• Yin KF, Han Y, Liu Y. Experimental research on bond strength between rebar and concrete after high temperature. In Applied mechanics and materials. Bäch (Switzerland): Trans Tech Publications; 2011.
   Google Scholar
• Hassan SA. Effect of elevated temperatures on bond strength of steel reinforcement and concrete enhanced with discrete carbon fibers. J Eng Sustain Dev. 2012;16(4):30–46.
   Google Scholar
• Trezos KG, Sfikas IP. Residual bond stress of self-compacting concrete specimens after high temperature treatment. In Proceedings of the 7th RILEM International Conference on Self-Compacting Concrete and 1st RILEM International Conference on Rheology and Processing of Construction Materials. Paris (France): RILEM Publications; 2013.
   Google Scholar
• Xiao J, Hou Y, Huang Z. Beam test on bond behavior between high-grade rebar and high-strength concrete after elevated temperatures. Fire Saf J. 2014;69:23–35.
   Web of Science ®Google Scholar
• Arel HS, Yazici S. Effect of different parameters on concrete-bar bond under high temperature. ACI Mater J. 2014;111(6):633.
   Web of Science ®Google Scholar
• Lublóy É, György BL. Temperature effects on bond between concrete and reinforcing steel. Zbornik Gfs. 2014;30(26):27–35.
   Google Scholar
• Sezer Gİ, Sezer A, Yazıcı Ş. Evaluation of high temperature effects on concrete-reinforcement bar bond using automated digital image processing. Indian J Eng Mater Sci. 2015;22:581–586.
   Web of Science ®Google Scholar
• Yang H, Lan W, Qin Y, et al. Evaluation of bond performance between deformed bars and recycled aggregate concrete after high temperatures exposure. Constr Build Mater. 2016;112:885–891.
   Web of Science ®Google Scholar
• Ergün A, Kürklü G, Başpınar MS. The effects of material properties on bond strength between reinforcing bar and concrete exposed to high temperature. Constr Build Mater. 2016;112:691–698.
   Web of Science ®Google Scholar
• Hlavička ÉL-V. Bond after fire. Constr Build Mater. 2017;132:210–218.
   Web of Science ®Google Scholar
• Bošnjak J, Sharma A. Bond between steel and concrete under fire‐from laboratory tests to fire performance. Paper presented at the 3rd International Symposium on Connections between Steel and Concrete; 2017 September 27–29; Stuttgart (Germany).
   Google Scholar
• Li Q, Huang X, Huang Z, et al. Bond characteristics between early aged fly ash concrete and reinforcing steel bar after fire. Constr Build Mater. 2017;147:701–712.
   Web of Science ®Google Scholar
• Shamseldein A, Elshafie H, Rashad A, et al. Assessment and restoration of bond strength of heat-damaged reinforced concrete elements. Constr Build Mater. 2018;169:425–435.
   Web of Science ®Google Scholar
• Zhang HY, Kodur V, Wu B, et al. Effect of temperature on bond characteristics of geopolymer concrete. Constr Build Mater. 2018;163:277–285.
   Web of Science ®Google Scholar
• Varona FB, Baeza FJ, Bru D, et al. Evolution of the bond strength between reinforcing steel and fibre reinforced concrete after high temperature exposure. Constr Build Mater. 2018;176:359–370.
   Web of Science ®Google Scholar
• Tang C-W. Local bond-slip behavior of medium and high strength fiber reinforced concrete after exposure to high temperatures. Struct Eng Mech. 2018;66:477–485.
   Web of Science ®Google Scholar
• Bošnjak J, Sharma A, Öttl C. Modified beam-end test setup to study the bond behavior of reinforcement in concrete after fire. Mater Struct. 2018;51(1):13.
   Web of Science ®Google Scholar
• Rashid MH, Molla M, Taki IM. Effect of elevated temperature on bond strength of concrete. MSF. 2019;972:26–33.
   Google Scholar
• Agnoletti A, Consiglio A, Muciaccia G, et al. Effects of elevated temperatures and of loading procedures on the bond performance of reinforcement in concrete. in 9th International Conference On Concrete Under Severe Conditions-Environment and Loading; 2019 June 5–7; Porto Alegre, Brazil.
   Google Scholar
• Sharma A, Bošnjak J, Bessert S. Experimental investigations on residual bond performance in concrete subjected to elevated temperature. Eng Struct. 2019;187:384–395.
   Web of Science ®Google Scholar
• Varghese A, Anand N, Arulraj GP, et al. Influence of fibers on bond strength of concrete exposed to elevated temperature. J Adhes Sci Technol. 2019;33(14):1521–1543.
   Web of Science ®Google Scholar
• Bengar HA, Hosseinpour M, Celikag M. Influence of CFRP confinement on bond behavior of steel deformed bar embedded in concrete exposed to high temperature. In Structures. Amsterdam (The Netherlands): Elsevier; 2020.
   Google Scholar
• Sureshbabu N, Mathew G. Influence of temperature on bond–slip characteristics of concrete containing fly ash. Asian J Civ Eng. 2020;21(6):1013–1023.
   Google Scholar
• Guizani L, Chaallal O, Mousavi SS. Local bond stress-slip model for reinforced concrete joints and anchorages with moderate confinement. Can J Civ Eng. 2017;44(3):201–211.
   Web of Science ®Google Scholar
• Morley P. Influence of fire on bond in reinforced concrete structures. Edinburgh (UK): Department Civil Engineering and Building Science, University of Edinburgh; 1977.
   Google Scholar
• Schneider U, Diederichs U. Untersuchung des Verbundverhaltens und der Verbundfestigkeit von Rippenstäben und glatten Rundstäben bei hohen Temperaturen (Entwicklung und Erprobung einer Prüfapparatur): Institut für Baustoffkunde und Stahlbetonbau; Der Technische Universität Braunschweig, (in German), Braunschweig. 1978. DOI: 10.24355/dbbs.084-201703031212-0
   Google Scholar
• Diederichs U, Schneider U. Bond strength at high temperatures. Mag Concr Res. 1981;33(115):75–84.
   Web of Science ®Google Scholar
• Raouffard MM, Nishiyama M. Idealization of bond stress-slip relationship at elevated temperatures based on pullout tests. ACI Structural Journal. 2018;115(2):391–400.
   Web of Science ®Google Scholar
• Zhang B, Zhu H, Chen J, et al. Evaluation of bond performance of corroded steel bars in concrete after high temperature exposure. Eng Struct. 2019;198:109479.
   Web of Science ®Google Scholar
• Parthasarathi N, Satyanarayanan K. Mechanical properties and bond strength of concrete at high temperature under steady-state conditions. Paper presented at the 2020 6th International Conference on Advanced Computing and Communication Systems (ICACCS); 2020 March 6–7. Piscataway, NJ.
   Google Scholar
• Mousavi SS, Ouellet-Plamondon CM, Guizani L, et al. On mitigating rebar–concrete interface damages due to the pre-cracking phenomena using superabsorbent polymers. Constr Build Mater. 2020;253:119181.
   Web of Science ®Google Scholar
• Mousavi SS, Guizani L, Bhojaraju C, et al. The effect of air-entraining admixture and superabsorbent polymer on bond behaviour of steel rebar in pre-cracked and self-healed concrete. Constr Build Mater. 2021;281:122568.
   Web of Science ®Google Scholar
• Chung L, Najm H, Balaguru P. Flexural behavior of concrete slabs with corroded bars. Cem Concr Compos. 2008;30(3):184–193.
   Web of Science ®Google Scholar
• Almusallam AA, et al. Effect of reinforcement corrosion on flexural behavior of concrete slabs. J Mater Civil Eng. 1996;8(3):123–127.
   Web of Science ®Google Scholar
• Chung L, Cho S-H, Jay Kim J-H, et al. Correction factor suggestion for ACI development length provisions based on flexural testing of RC slabs with various levels of corroded reinforcing bars. Eng Struct. 2004;26(8):1013–1026.
   Web of Science ®Google Scholar
• Kearsley EP, Joyce A. Effect of corrosion products on bond strength and flexural behaviour of reinforced concrete slabs. J South African Inst Civ Eng. 2014;56(2):21–29.
   Web of Science ®Google Scholar
• Wu S-X, Liu G-G, Bian H-B, et al. Degradation and mechanism of the mechanics and durability of reinforced concrete slab in a marine environment. China Ocean Eng. 2016;30(2):257–270.
   Web of Science ®Google Scholar
• Mousavi SS, Guizani L, Bhojaraju C, et al. Effect of concrete workability on bond properties of steel rebar in pre-cracked concrete. Struct Build. 2021;1–34. https://doi.org/10.1680/jstbu.20.00111.
   Google Scholar
• Naik TR, Kraus RN, Kumar R. Influence of types of coarse aggregates on the coefficient of thermal expansion of concrete. J Mater Civ Eng. 2011;23(4):467–472.
   Web of Science ®Google Scholar
• Mindeguia J-C, Pimienta P, Carré H, et al. On the influence of aggregate nature on concrete behaviour at high temperature. European J Env Civ Eng. 2012;16(2):236–253.
   Web of Science ®Google Scholar
• Ndon UJ, Bergeson K. Thermal expansion of concretes: case study in Iowa. J Mater Civ Eng. 1995;7(4):246–251.
   Web of Science ®Google Scholar
• Kodur V, Sultan M. Effect of temperature on thermal properties of high-strength concrete. J Mater Civ Eng. 2003;15(2):101–107.
   Web of Science ®Google Scholar
• Goudar SK, Das B, Arya S. Microstructural study of steel-concrete interface and its influence on bond strength of reinforced concrete. Adv Civ Eng Matls. 2019;8(1):20180133–20180189.
   Web of Science ®Google Scholar
• Zayed AM. The nature of the concrete-steel rebar interface in plain and silica fume concrete. MRS Online Proc Libr. 1991;245(1):341–347.
   Google Scholar
• Kenny A, Katz A. Characterization of the interfacial transition zone around steel rebar by means of the mean shift method. Mater Struct. 2012;45(5):639–652.
   Web of Science ®Google Scholar
• Chen F, Li C-Q, Baji H, et al. Effect of design parameters on microstructure of steel-concrete interface in reinforced concrete. Cem Concr Res. 2019;119:1–10.
   Web of Science ®Google Scholar
• Horne A, Richardson I, Brydson R. Quantitative analysis of the microstructure of interfaces in steel reinforced concrete. Cem Concr Res. 2007;37(12):1613–1623.
   Web of Science ®Google Scholar
• Scrivener K, 1999. Characterisation of the ITZ and its quantification by test methods. In Alexander MG, Arliguie G, Ballivy G, Bentur A, and Marchand J, Engineering and transport properties of the interfacial transition zone in cementitious composites—State-of-the-art report of RILEM TC 159-ETC and 163-TPZ, 3–15. Paris: RILEM Publications SARL.
   Google Scholar
• Elsharief A, Cohen MD, Olek J. Influence of aggregate size, water cement ratio and age on the microstructure of the interfacial transition zone. Cem Concr Res. 2003;33(11):1837–1849.
   Web of Science ®Google Scholar
• Liu K, Zou C, Yan J, et al. Bond behavior of deformed steel bars in self-compacting concrete. J Adhes Sci Technol. 2021;35(14):1518–1533.
   Web of Science ®Google Scholar
• Yoo D-Y, Shin H-O. Bond performance of steel rebar embedded in 80–180 MPa ultra-high-strength concrete. Cem Concr Compos. 2018;93:206–217.
   Web of Science ®Google Scholar
• Islam K, Billah AM, Chowdhury MMI, et al. Exploratory study on bond behavior of plain and sand coated stainless steel rebars in concrete. in. Structures. 2020;27:2365–2378.
   Web of Science ®Google Scholar
• Pour SM, Alam MS. Investigation of compressive bond behavior of steel rebar embedded in concrete with partial recycled aggregate replacement. In Structures. Amsterdam (the Netherlands): Elsevier; 2016.
   Google Scholar
• Xing G, Zhou C, Wu T, et al. Experimental study on bond behavior between plain reinforcing bars and concrete. Adv Mater Sci Eng. 2015;2015:1–9.
   Web of Science ®Google Scholar
• Singh B, Ishwarya G, Gupta M, et al. Geopolymer concrete: a review of some recent developments. Constr Build Mater. 2015;85:78–90.
   Web of Science ®Google Scholar
• Ahmad S, Pilakoutas K, Masood Rafi M, et al. Experimental investigation of bond characteristics of deformed and plain bars in low strength concrete. Scientia Iranica. 2017;25(6):2954–2966.
   Web of Science ®Google Scholar
• Mo KH, Yeap KW, Alengaram UJ, et al. Bond strength evaluation of palm oil fuel ash-based geopolymer normal weight and lightweight concretes with steel reinforcement. J Adhes Sci Technol. 2018;32(1):19–35.
   Web of Science ®Google Scholar
• Kim D-J, Kim MS, Yun GY, et al. Bond strength of steel deformed rebars embedded in artificial lightweight aggregate concrete. J Adhes Sci Technol. 2013;27(5–6):490–507.
   Web of Science ®Google Scholar
• Harajli MH, Hamad BS, Rteil AA. Effect of confinement of bond strength between steel. ACI Struct J. 2004;101(5):595–603.
   Web of Science ®Google Scholar
• Sulaiman MF, Ma C-K, Apandi NM, et al. A review on bond and anchorage of confined high-strength concrete. Structures. 2017;11:97–109.
   Web of Science ®Google Scholar
• Mousavi S, Ouellet-Plamondon C, Guizani L. Effect of superabsorbent polymer on mitigating damages at steel bar–concrete interface. Paper presented at the CSCE Annual Conference; June. 2019 June 12–15; Laval, Canada.
   Google Scholar
• Lu L, Yuan G, Shu Q, et al. Bond behaviour between early age concrete and steel bar subjected to cyclic loading after fire. Fire Saf J. 2019;105:129–143.
   Web of Science ®Google Scholar