References
- Zhang YN, Cao X, Larose S, et al. Review of tools for friction stir welding and processing. Can Metall Q. 2012;51(3):250–261.
- Shah LH, Walbridge S, Gerlich A. Tool eccentricity in friction stir welding: a comprehensive review. Sci Technol Weld Joining. 2019;24(6):566–578.
- Xiong JT, Li JL, W Qian J, et al. High strength lap joint of aluminium and stainless steels fabricated by friction stir welding with cutting pin. Sci Technol Weld Joining. 2012;17(3):196–201.
- Ikuta A, North TH. Characteristics of friction stir spot welding tools in consideration of cutting tools. Quart J Jpn Weld Soc. 2019;37(4):224–231.
- Ikuta A. Characteristics of material flow on friction stir spot welding tool in consideration of cutting tools. Quart J Jpn Weld Soc. 2020;38(3):125–133.
- Fratini L, Buffa G, Palmeri D, et al. Material flow in FSW of AA7075–T6 butt joints: numerical simulations and experimental verifications. Sci Technol Weld Joining. 2006;11(4):412–421.
- Mehta M, De A, DebRoy T. Material adhesion and stresses on friction stir welding tool pins. Sci Technol Weld Joining. 2014;19(6):534–540.
- Ikuta A, North TH. Influence of material adhered to tool on friction stir spot welds. Quart J Jpn Weld Soc. 2017;35(4):171–178.
- Badarinarayan H, Shi Y, Li X, et al. Effect of tool geometry on hook formation and static strength of friction stir spot welded aluminum 5754-O sheets. Int J Mach Tools Manuf. 2009;49(11):814–823.
- Buffa G, Campanile G, Fratini L, et al. Friction stir welding of lap joints – influence of process parameters on the metallurgical and mechanical properties. Mater Sci Eng, A. 2009;519(1–2):19–26.
- Ikuta A, Yin YH, North TH. Influence of tool thread on mechanical properties of dissimilar Al alloy friction stir spot welds. Sci Technol Weld Joining. 2012;17(8):622–629.
- Horie S, Shinozaki K, Yamamoto M, et al. Experimental investigation of material flow during friction stir spot welding. Sci Technol Weld Joining. 2010;15(8):666–670.
- Prangnell PB, Heason CP. Grain structure formation during friction stir welding observed by the ‘stop action technique. Acta Mater. 2005;53(11):3179–3192.
- Segawa T, Sasahara H, Kagiya Y, et al. Visualization and analysis of chip ejection process in dry drilling of aluminum alloy. J Jpn Soc Prec Eng. 2005;71(5):623–627.
- Kasahara K, Hirota A. Drilling with flat rake face drills and analysis of long-pitch helical chip formation process. J Jpn Soc Prec Eng. 1990;56(6):1075–1081.
- Hanasaki S, Hosoi R, Hosoi T, et al. Chip exhaust mechanism of twist drill drillable deep hole under continuously high feed rate. Transjsme, Serc. 1999;65(631):1229–1234.
- Shibayanagi T, Gerlich AP, Kashihara K, et al. Textures in single-crystal aluminum friction stir spot welds. Metall and Mat Trans A. 2009;40(4):920–931.
- Su P, Gerlich A, North TH, et al. Material flow during friction stir spot welding. Sci Technol Weld Joining. 2006;11(1):61–71.
- Su P, Gerlich A, North TH, et al. Intermixing in dissimilar friction stir spot welds. Metall and Mat Trans A. 2007;38(3):584–595.
- Gerlich A, Su P, Yamamoto M, et al. Material flow and intermixing during dissimilar friction stir welding. Sci Technol Weld Joining. 2008;13(3):254–264.
- Zhang D, Shibayanagi T. Material flow during friction stir spot welding of dissimilar Al2024/Al materials. Mater Sci Technol. 2015;31(9):1077–1087.
- Tomonaga N, Takano A, Kawanishi S, et al. Material flow promoting effect of the friction stir welding by double spiral tool. Quart J Jpn Weld Soc. 2020;38(1):34–40.