Experimental studies on key-hole plasma arc welding process parameters of AISI 304 HCu stainless steel tube joints

References

• Ravibharath R, Muthupandi V, Bala Srinivasan P, et al. Characterization of solidification cracking in 304HCu austenitic stainless steel welds. Trans Indian Inst Met. 2020;73(9):2345–2353.
   Web of Science ®Google Scholar
• Viswanathan R, Coleman K, Rao U. Materials for ultra-supercritical coal-fired power plant boilers. Int J Press Vessels Pip. 2006;83(11-12):778–783.
   Web of Science ®Google Scholar
• Srinivasan G, Dey HC, Ganesan V, et al. Choice of welding consumable and procedure qualification for welding of 304HCu austenitic stainless steel boiler tubes for indian advanced ultra super critical power plant. Weld World. 2016;60(5):1029–1036.
   Web of Science ®Google Scholar
• Pavan AHV, Vikrant KSN, Ravibharath R, et al. Development and evaluation of SUS 304H - IN 617 welds for advanced ultra supercritical boiler applications. Mater Sci Eng A. 2015;642:32–41.
   Web of Science ®Google Scholar
• Reddy AA, Guha B, Achar DRG. Finite element modeling of three-dimensional transient heat transfer in stainless steel (304) pulsed GTA weldments. Numeri Heat Transf A Appl. 2002;41(1):41–64.
   Web of Science ®Google Scholar
• Wei Y, Xu Y, Dong Z, et al. Three-dimensional monte carlo simulation of discontinuous grain growth in HAZ of stainless steel during GTAW process. J Mater Process Technol. 2009;209(3):1466–1470.
   Web of Science ®Google Scholar
• Vinoth Kumar M, Balasubramanian V. Effect of current pulsing on super 304HCu weld joints. WJE. 2019;16(6):814–822.
   Web of Science ®Google Scholar
• Rizvi SA. Application of taguchi technique to optimize the gma welding parameters and study of fracture mode characterization of aisi 304H welded joints. IRASE. 2018;9(1):9–16.
   Google Scholar
• Sharma P, Dwivedi DK. Study on flux assisted-Tungsten inert gas welding of bimetallic P92 martensitic steel-304H austenitic stainless steel using SiO2–TiO2 binary flux. Int J Press Vessels Pip. 2021;192:104423.
   Web of Science ®Google Scholar
• Sharma P, Dwivedi DK. Comparative study of activated flux-GTAW and multipass-GTAW dissimilar P92 steel-304H ASS joints. Mater Manuf Processes. 2019;34(11):1195–1204.
   Web of Science ®Google Scholar
• Her-Yueh H. Research on the activating flux gas tungsten arc welding and plasma arc welding for stainless steel. 2010.
   Google Scholar
• Harish TM, Jerome S, Yadukrishna B, et al. Assessment of microstructure and mechanical properties of keyhole plasma arc welded similar butt joint of AISI 304 H austenitic stainless steel. Mater Res Express. 2019;6:1165b2.
   Google Scholar
• Hsiao YF, Tarng YS, Huang WJ. Optimization of plasma arc welding parameters by using the taguchi method with the grey relational analysis. Mater Manuf Processes. 2007;23(1):51–58.
   Web of Science ®Google Scholar
• Feng Y, Luo Z, Liu Z, et al. Keyhole gas tungsten arc welding of AISI 316L stainless steel. Mater Des. 2015;85:24–31.
   Web of Science ®Google Scholar
• Gupta R, Reddy R, Mukherjee MK. Key- Hole plasma arc welding of 8 Mm thick maraging steel — a comparison with Multi- Pass gtaw. Weld World. 2012;56(9-10):69–75.
   Web of Science ®Google Scholar
• Ureña A, Otero E, Utrilla M V, et al. Weldability of a 2205 duplex stainless steel using plasma arc welding. J Mater Process Technol. 2007;182(1-3):624–631.
   Web of Science ®Google Scholar
• Wu CS, Wang L, Ren WJ, et al. Plasma arc welding: process, sensing, control and modeling. J Manuf Process. 2014;16(1):74–85.
   Web of Science ®Google Scholar
• Utsumi A, Matsuda J, Yoneda M, et al. Effect of gas flow rate on shapes of weld bead sections. Study on high-speed surface treatment by arc with laser (2nd report). Weld Int. 2001;15(5):345–353.
   Google Scholar
• Maruyama K, Takeda K, Sugimoto M, et al. Long arc stabilities with various arc gas flow rates. J Phys Conf Ser. 2014;550:012009.
   Google Scholar
• Huu MN, van Nguyen A, van Nguyen T, et al. Material flow behavior on weld Pool surface in plasma arcwelding process considering dominant driving forces. Applied Sciences (Switzerland). 2020;10(10):3569.
   Web of Science ®Google Scholar
• Tseng KH, Hsieh ST, Tseng CC. Effect of process parameters of micro-plasma arc welding on morphology and quality in stainless steel edge joint welds. Sci Technol Weld Joining. 2003;8(6):423–430.
   Web of Science ®Google Scholar