References
- Holdsworth SR . Influence of prior fatigue on creep properties. 12th International Conference on Creep and Fracture of Engineering Materials and Structures, Creep 2012; 2012 May 27–31; Kyoto, Japan.
- Fournier B , Sauzay M , Caës FC , et al . Creep-fatigue interactions in a 9Cr-1Mo martensitic steel: part II. microstructural evolutions. Metall Mater Trans A. 2009;40(2):330–341.10.1007/s11661-008-9687-y
- Radosavljevic M . Creep-fatigue assessment of high temperature steam turbine rotors (Diss ETH No. 19880) [ PhD thesis]. Zürich: ETHZ University; 2011.
- Hosseini E , Holdsworth SR , Kühn I , et al . Modelling heat-to-heat variability in high temperature cyclic deformation behaviour. Mater High Temp. 2015;32(3):347–354.10.1179/0960340914Z.00000000078
- Holdsworth SR , Radosavljevic M , Grossmann P , et al . Effectiveness verification of creep-fatigue assessment procedures for fast-starting steam turbines. In: ASME Turbine Technical Conference and Exposition, American Society of Mechanical Engineers. 2012. p. 367–373.
- Hosseini E , Holdsworth SR , Kühn I , et al . Temperature dependent representation for Chaboche kinematic hardening model. Mater High Temp. 2015;32(4):404–412.10.1179/1878641314Y.0000000036
- Hosseini E , Holdsworth SR , Mazza E . Temperature and stress–regime dependent primary-secondary-tertiary creep constitutive model. Mater High Temp. 2015;32(4):384–389.10.1179/1878641314Y.0000000029
- Chaboche JL . Time-independent constitutive theories for cyclic plasticity. Int J Plast. 1986;2(2):149–188.10.1016/0749-6419(86)90010-0
- Bolton J . A ‘Characteristic-Strain’ model for creep. Mater High Temp. 2008;25(3):197–204.10.3184/096034008X357573
- Manson S , Ensign C . Interpolation and extrapolation of creep rupture data by the minimum commitment method. In: Smith GV , editor. Characterization of materials for service at elevated temperatures, MPC-7. New York (NY) : ASME; 1978. p. 299–398.
- High Temperature Design Data for Ferritic Pressure Vessel Steels . Institution of Mechanical Engineers (Great Britain). Creep of steels working party. Mechanical Engineering Publications; 1983.
- Holdsworth SR , Hosseini E . Primary creep persistency (creep re-priming), a status review for R5 panel; 2017.
- ASME III . ASME boiler and pressure vessel code. New York (NY): Section III, Division 1: Sub-section NH, Class 1 Components in Elevated Temperature Service; 2004.
- RCC-MR . Design and construction rules for mechanical components of FBR nuclear Islands. Paris: AFCEN; 2007.
- R5 . Assessment procedure for the high temperature response of structures. Gloucester: British Energy; 2003.
- Hales R . A method of creep damage summation based on accumulated strain for the assessment of creep-fatigue endurance. Fatigue Fract Eng Mater Struct. 1983;6(2):121–135.10.1111/ffe.1983.6.issue-2
- Spindler MW , Payten WM . Advanced ductility exhaustion methods for the calculation of creep damage during creep-fatigue cycling. J ASTM Int. 2011;8(7):1–19.
- Holdsworth SR . Component assessment data requirements from creep-fatigue tests. J ASTM Int. 2011;8(3):1–14.
- ASTM E2368 . Standard practice for strain controlled thermomechanical fatigue testing, in book of standards volume: 03.01; 2004.
- Radosavljevic M , Holdsworth SR . Novel induction heating system for service cycle thermomechanical fatigue testing. Mater High Temp. 2009;26(4):369–374.10.3184/096034009X12563979940798