References
- Abdelhalim, R. A., et al., 2020. Experimental and numerical studies of laterally loaded piles located near oil-contaminated sand slope. J Engineering Science Technology, an International Journal, 23 (4), 744–757. doi: https://doi.org/10.1016/j.jestch.2020.03.001
- Ajagbe, W. O., et al., 2012. Effect of crude oil impacted sand on compressive strength of concrete. J Construction Building Materials, 26 (1), 9–12. doi: https://doi.org/10.1016/j.conbuildmat.2011.06.028
- Akinwumi, I. I., et al., 2016. Cement stabilisation of crude-oil-contaminated soil. J Proceedings of the ICE-Geotechnical Engineering, 169 (4), 336–345. doi: https://doi.org/10.1680/jgeen.15.00108
- Al-Duwaisan, D. B., and Al-Naseem, A. A., 2011. Characterization of oil contaminated soil-Kuwait oil lakes. In: Proceedings of international Conference on Environmental Science and Technology (ICEST 2011). (pp. 439–442).
- Al-Mutairi, N. M., and Eid, W. K, 1997. Utilization of oil-contaminated sands in asphalt concrete for secondary roads. J Materials Structures, 30 (8), 497–505. doi: https://doi.org/10.1007/BF02524778
- Al-Rawas, A., et al., 2005. Stabilization of oil-contaminated soils using cement and cement by-pass dust. Management of Environmental Quality: An International Journal, 16 (6), 670–680. doi: https://doi.org/10.1108/14777830510623736
- Al-Sanad, H. A., Eid, W. K., and Ismael, N. F, 1995. Geotechnical properties of oil-contaminated Kuwaiti sand. Journal of Geotechnical Engineering, 121 (5), 407–412. doi: https://doi.org/10.1061/(ASCE)0733-9410(1995)121:5(407)
- Al-Taher, M. G., et al., 2018. Investigation of the effect of adding silica fume on asphalt concrete properties. International Journal of Engineering Research, 7 (4), 48–55. doi: https://doi.org/10.5958/2319-6890.2018.00095.8
- Asphalt-Institute, 2014. MS-2 asphalt mix design methods. J Asphalt Institute: Lexington Kentucky, USA.
- ASTM D-1557-12e1, 2012. Standard test methods for laboratory compaction characteristics of soil using modified effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3)), ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D1557-12E01, www.astm.org.
- ASTM D-1883-16, 2016. Standard test method for California bearing ratio (CBR) of laboratory-compacted soils, ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D1883-16, www.astm.org.
- ASTM D-2270-10, 2010. Standard practice for calculating viscosity index from kinematic viscosity at 40 and 100°C, ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D2270-1, www.astm.org.
- ASTM D-2434-19, 2019. Standard test method for permeability of granular soils (constant head), ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D2434-19, www.astm.org.
- ASTM D-2487-17e1, 2017. Standard practice for classification of soils for engineering purposes (Unified Soil Classification System), ASTM International, West Conshohocken, PA, 2017, DOI: https://doi.org/10.1520/D2487-17E01,<otherinfo> www.astm.org.
- ASTM D-3080M-11 / D3080, 2011. Standard test method for direct shear test of soils under consolidated drained conditions (Withdrawn 2020), ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D3080_D3080M-11, www.astm.org.
- ASTM D-3282-15, 2015. Standard practice for classification of soils and soil-aggregate mixtures for highway construction purposes, ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D3282-15, www.astm.org.
- ASTM D-4052-18a, 2018. Standard test method for density, relative density, and API gravity of liquids by digital density meter, ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D4052-18A, www.astm.org.
- ASTM D-445-19a, 2019. Standard test method for kinematic viscosity of transparent and opaque liquids (and calculation of dynamic viscosity), ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D0445-19A, www.astm.org.
- ASTM D-5355-95, 1995. Standard test method for specific gravity of oils and liquid fats, ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D5355-95, www.astm.org.
- ASTM D-6528-17, 2017. Standard test method for consolidated undrained direct simple shear testing of fine grain soils, ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D6528-17, www.astm.org.
- ASTM D-92-12, 2012. Standard test method for flash and fire points by Cleveland open cup tester, ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D0092-12, www.astm.org.
- ASTM D-97-17b, 2017. Standard test method for pour point of petroleum products, ASTM International, West Conshohocken, PA, DOI: https://doi.org/10.1520/D0097-17B, www.astm.org.
- Bandeira, A. A., Fortes, R. M., and Merighi, J. V, 2009. A study of the hot-mix asphalt layer thickness reduction when applied over lateritic soils cement base in airfield. J Exacta, 7 (1), 121–131.
- Blight, G., and Leong, E, 2012. Mechanics of residual soils (2nd ed.). London: Taylor & Francis.
- Czarnecki, R. C, 1988. Making use of contaminated soil. J Civil Engineering, 58 (12), 72.
- Ejeh, S., and Uche, O, 2009. Effect of crude oil spill on compressive strength of concrete materials. Journal of Applied Sciences Research, 5 (10), 1756–1761.
- Evgin, E., and Das, B., 1992. Mechanical behavior of an oil contaminated sand. In: Usmen & Acar (Eds), Environmental Geotechnology, Rotterdam: Balkema.
- Fingas, M, 2016. Oil spill science and technology. 2nd ed., Gulf professional publishing.
- George, S., et al., 2015. Stabilization of diesel oil contaminated soil using fly ash. Int. J. Civil Struct. Eng. Res, 2 (2), 118–123.
- Gourley, C., and Greening, P. A. K, 1999. Performance of low volume sealed roads: Results and recommendations from studies in Southern Africa. PROJECT REPORT PR/OSC/167/99. Transport Research Laboratory, Department for International Development, Crowthorne, Berkshire, UK.
- Grace, H, 1991. Investigations in Kenya and Malawi using as-dug laterite as bases for bituminous surfaced roads. J Geotechnical Geological Engineering, 9 (3-4), 183–195. doi: https://doi.org/10.1007/BF00881740
- Han, Y., Nambi, I. M., and Clement, T. P, 2018. Environmental impacts of the Chennai oil spill accident–A case study. J Science of the Total Environment, 626, 795–806. doi: https://doi.org/10.1016/j.scitotenv.2018.01.128
- Hassan, H. F., et al., 2005. Potential uses of petroleum-contaminated soil in highway construction. J Construction Building Materials, 19 (8), 646–652. doi: https://doi.org/10.1016/j.conbuildmat.2005.01.001
- Hassan, H. F., et al., 2008. Investigation of permeability and leaching of hot mix asphalt concrete containing oil-contaminated soils. J Construction Building Materials, 22 (6), 1239–1246. doi: https://doi.org/10.1016/j.conbuildmat.2007.01.017
- Huang, F., and Lu, H, 2014. Experiment study on the Atterberg limits of clay contaminated by Oil. Electronic Journal of Geotechnical Engineering, 19, 3037–3046.
- Kadafa, A. A, 2012. Oil exploration and spillage in the Niger Delta of Nigeria. J Civil Environmental Research, 2 (3), 38–51.
- Khamehchiyan, M., Charkhabi, A. H., and Tajik, M, 2007. Effects of crude oil contamination on geotechnical properties of clayey and sandy soils. J Engineering Geology, 89 (3-4), 220–229. doi: https://doi.org/10.1016/j.enggeo.2006.10.009
- Khosravi, E., et al., 2013. Geotechnical properties of gas oil-contaminated kaolinite. J Engineering Geology, 166, 11–16. doi: https://doi.org/10.1016/j.enggeo.2013.08.004
- Lohnes, R. A., and Demirel, T, 1973. Strength and structure of Laterites and Lateritic soils. Engineering Geology, 7 (1), 13–33. doi: https://doi.org/10.1016/0013-7952(73)90004-5
- Malomo, S, 1989. Microstructural investigation on latérite soils. J Bulletin of the International Association of Engineering Geology-Bulletin de L'Association Internationale de Géologie de L'Ingénieur, 39 (1), 105–109. doi: https://doi.org/10.1007/BF02592542
- Meegoda, J., et al., 1994. Petroleum contaminated soils in highway construction. In: Proceedings of the 3rd materials Engineering Conference (pp. 904–911): ASCE.
- Mengue, E., et al., 2017. Mechanical improvement of a fine-grained lateritic soil treated with cement for use in road construction. Journal of Materials in Civil Engineering, 29 (11), 04017206. doi: https://doi.org/10.1061/(ASCE)MT.1943-5533.0002059
- Mousavi, S, 2017. Shear strength behavior in the interface of contaminated soil with bio-diesel oil and geosynthetics. J Transportation Geotechnics, 10, 62–72. doi: https://doi.org/10.1016/j.trgeo.2016.12.003
- Nasr, A. M, 2014. Utilisation of oil-contaminated sand stabilised with cement kiln dust in the construction of rural roads. J International Journal of Pavement Engineering, 15 (10), 889–905. doi: https://doi.org/10.1080/10298436.2014.893321
- Nasr, A., and Krishna Rao, S, 2015. Behaviour of laterally loaded pile groups embedded in oil-contaminated sand. J Géotechnique, 66 (1), 58–70. doi: https://doi.org/10.1680/jgeot.15.P.076
- Offiong, U. D., and Akpan, G. E, 2017. Assessment of physico-chemical properties of periwinkle shell ash as partial replacement for cement in concrete. International Journal of Scientific Engineering and Science, 1 (7), 33–36.
- Ola, S, 1978. Geotechnical properties and behaviour of some stabilized Nigerian lateritic soils. Quarterly Journal of Engineering Geology Hydrogeology, 11 (2), 145–160. doi: https://doi.org/10.1144/GSL.QJEG.1978.011.02.04
- Paige-Green, P., Pinard, M., and Netterberg, F, 2015. A review of specifications for lateritic materials for low volume roads. J Transportation Geotechnics, 5, 86–98. doi: https://doi.org/10.1016/j.trgeo.2015.10.002
- Pakbaz, M., Behzadipour, H., and Ghezelbash, G, 2018. Evaluation of shear strength parameters of sandy soils upon microbial treatment. Geomicrobiology Journal, 35 (8), 721–726. doi: https://doi.org/10.1080/01490451.2018.1455766
- Patel, A., 2011. Study of geotechnical properties of black cotton soil contaminated by castor oil and stabilization of contaminated soil by sawdust. In: National Conference on Recent Trends in Engineering & Technology, 2011 (pp. 13–14).
- Persons, B. S, 1970. Laterite: genesis, location, use. Springer Science & Business Media.
- Putri, E. E., Rao, N., and Mannan, M, 2012. Evaluation of modulus of elasticity and modulus of subgrade reaction of soils using CBR test. Journal of Civil Engineering Research, 2 (1), 34–40. doi: https://doi.org/10.5923/j.jce.20120201.05
- Qian, J., et al., 2017. Laboratory characterization of cement–lateritic gravel for use in base construction. Journal of Materials in Civil Engineering, 29 (3), D4015001. doi: https://doi.org/10.1061/(ASCE)MT.1943-5533.0001466
- Ratnaweera, P., and Meegoda, J. N, 2005. Shear strength and stress-strain behavior of contaminated soils. Geotechnical Testing Journal, 29 (2), 133–140.
- Rezaei, S., et al., 2017. The effect of nano-SiO2 and the styrene butadiene styrene polymer on the high-temperature performance of hot mix asphalt. J Petroleum Science Technology, 35 (6), 553–560. doi: https://doi.org/10.1080/10916466.2016.1270301
- Rolt, J., et al., 2013. Back analysis of previous constructed low volume rural roads in Mozambique. Wantage: AFCAP. Department of Foreign and International Development.
- Rosone, M., Celauro, C., and Ferrari, A, 2020. Microstructure and shear strength evolution of a lime-treated clay for use in road construction. International Journal of Pavement Engineering, 21 (9), 1147–1158. doi: https://doi.org/10.1080/10298436.2018.1524144
- Saberian, M., and Khabiri, M. M, 2018. Effect of oil pollution on function of sandy soils in protected deserts and investigation of their improvement guidelines (case study: Kalmand area, Iran). J Environmental Geochemistry Health, 40 (1), 243–254. doi: https://doi.org/10.1007/s10653-016-9897-y
- Shah, S. J., et al., 2003. Stabilization of fuel oil contaminated soil—A case study. J Geotechnical Geological Engineering, 21 (4), 415–427. doi: https://doi.org/10.1023/B:GEGE.0000006052.61830.1a
- Shin, E., Lee, J., and Das, B, 1999. Bearing capacity of a model scale footing on crude oil-contaminated sand. Geotechnical Geological Engineering, 17 (2), 123–132. doi: https://doi.org/10.1023/A:1016078420298
- Sukhadane, K. S., et al., 2013. Status of oil pollution in Indian coastal waters. J Fishing Chimes, 33 (5), 53–54.
- Taherkhani, H., and Afroozi, S, 2017. Investigating the performance characteristics of asphaltic concrete containing nano-silica. Civil Engineering Infrastructures Journal, 50 (1), 75–93.
- Tardy, Y, 1997. Petrology of laterites and tropical soils: AA Balkema.
- TRL, T. R. L, 1993. A Guide to the structural design of bitumen-surfaced roads in tropical and sub-tropical countries. Wokingham: Overseas Centre, TRL.
- Tuncan, A., Tuncan, M., and Koyuncu, H, 2000. Use of petroleum-contaminated drilling wastes as sub-base material for road construction. J Waste Management Research, 18 (5), 489–505. doi: https://doi.org/10.1177/0734242X0001800511
- Umar, M., Kassim, K. A., and Chiet, K. T. P, 2016. Biological process of soil improvement in civil engineering: A review. Journal of Rock Mechanics Geotechnical Engineering, 8 (5), 767–774. doi: https://doi.org/10.1016/j.jrmge.2016.02.004
- Valore, C. and Ziccarelli, M., 2009. The evolution of grain-size distribution of sands under 1-D compression. In: 17th International Conference on soil Mechanics and geotechnical Engineering, 2009 (Vol. 1, pp. 84–88): IOS under the imprint Millpress.
- Wallace, K, 1973. Structural behaviour of residual soils of the continually wet highlands of Papua New Guinea. J Géotechnique, 23 (2), 203–218. doi: https://doi.org/10.1680/geot.1973.23.2.203
- Wang, M., et al., 2019. Efficient remediation of crude oil-contaminated soil using a solvent/surfactant system. J RSC Advances, 9 (5), 2402–2411. doi: https://doi.org/10.1039/C8RA09964B
- Zheng, X., et al., 2014. A developed technique for measuring water content in oil-contaminated porous media. Environmental Earth Sciences, 71 (3), 1349–1356. doi: https://doi.org/10.1007/s12665-013-2541-6
- Ziccarelli, M, 2016. Evolution of grain-size distribution of pumice sands in 1-D compression. J Procedia Engineering, 158 (6), 27–32. doi: https://doi.org/10.1016/j.proeng.2016.08.400