Comparison of Leakage Performance in Three Types of Gas Annular Seals Operating at a High Temperature (300°C)

REFERENCES

• Chupp , R. E. , Hendricks , R. C. , Lattime , S. B. and Steinetz , B. M. 2006 . “Sealing in Turbomachinery,” . J. Propul. Power , 22 ( 2 ) : 313 – 349 .
   Google Scholar
• Floyd , C. G. 1986 . “Gas Seals for Rotating Shafts,” . Tribol. Int. , 19 ( 4 ) : 204 – 211 .
   Google Scholar
• Alford , J. S. 1975 . “Nature, Causes, and Prevention of Labyrinth Air Seal Failures,” . J. Aircraft , 12 ( 4 ) : 313 – 318 .
   Google Scholar
• Tiwari , R. , Manikandan , S. and Dwivedy , S. K. 2005 . “A Review of the Experimental Estimation of the Rotor Dynamic Parameters of Seals,” . Shock Vib. Digest , 37 ( 4 ) : 261 – 284 .
   Google Scholar
• Chupp , R. E. , Johnson , R. P. and Loewenthal , R. G. 1995 . “Brush Seal Development for Large Industrial Gas Turbines,” AIAA Paper No. 1995-3146
   Google Scholar
• Ferguson , J. G. 1988 . “Brushes as High Performance Gas Turbine Seals,” ASME Paper No. 88-GT-182
   Google Scholar
• Crudgington , P. F. and Bowher , A. 2003 . “Brush Seal Blow Down,” AIAA Paper No. 2003-4697
   Google Scholar
• Conner , K. J. and Childs , D. W. 1993 . “Rotordynamic Coefficient Test Results for a Four-Stage Brush Seal,” . J. Propul. Power , 9 ( 3 ) : 462 – 465 .
   Google Scholar
• Dinc , S. , Demiroglu , M. , Turnquest , N. , Montzheim , J. , Goetze , G. , Manpin , J. , Hopkins , J. , Wolfe , C. and Florin , M. 2002 . “Fundamental Design Issues of Brush Seals for Industrial Applications,” . Journal of Turbomachinery , 124 ( 2 ) : 293 – 300 .
   Google Scholar
• Justak , J. F. and Crudgington , P. F. 2006 . “Evaluation of a Film Riding Hybrid Seal,” AIAA Paper No. 2006-4932
   Google Scholar
• San Andrés , L. , Baker , J. and Delgado , A. 2009 . “Measurements of Leakage and Power Loss in a Hybrid Brush Seal,” . Journal of Engineering for Gas Turbines & Power , 131 ( 1 ) : 012505
   Google Scholar
• Delgado , A. and San Andrés , L. 2007 . “Identification of Structural Stiffness and Damping Coefficients of a Shoed-Brush Seal,” . J. Vib. Acoust. , 129 ( 5 ) : 648 – 655 .
   Google Scholar
• San Andrés , L. , Baker , J. and Delgado , A. rdquo; Measurement of Leakage and Identification of Structural Force Coefficients in a Hybrid Brush Seal,” . Proceedings of the STLE Annual Meeting & Exhibition . May 19-21 , Cleveland, Ohio.
   Google Scholar
• San Andrés , L. , Delgado , D. and Baker , J. 2009 . “Rotordynamic Force Coefficients of a Hybrid Brush Seal: Measurements and Predictions,” . J. Eng. Gas Turbines Power , 132 : 042503
   Google Scholar
• Ashton , Z. 2009 . “High Temperature Leakage Performance of a Hybrid Brush Seal Compared to a Standard Brush Seal and a Labyrinth Seal,” , M. S. thesis College Station, TX : Texas A&M University .
   Google Scholar
• Delgado , I. R. and Proctor , M. P. 2006 . “Continued Investigation of Leakage and Power Loss Test Results for Competing Turbine Engine Seals,” AIAA Paper No. 2006-4754
   Google Scholar
• Chew , J. W. , Lapworth , B. L. and Milener , P. J. 1995 . Mathematical Modeling of Brush Seals,” . Int. J. Heat Fluid Flow , 16 : 493 – 500 .
   Google Scholar
• Chupp , R. E. and Holle , G. F. 1996 . “Generalizing Circular Brush Seal Leakage through a Randomly Distributed Bristle Bed,” . Journal of Turbomachinery , 118 : 153 – 161 .
   Google Scholar
• Childs , D. W. 1993 . Turbomachinery Rotordynamics: Phenomena, Modeling and Analysis , New York : John Wiley & Sons .
   Google Scholar