Numerical Prediction of Product Deformation and Identification of Major Controlling Factors during the IML Process Including Thermal Impact

REFERENCES

• I. Demirdzic , E. Dzaferovic , and A. Ivankovic , Finite-Volume Approach to Thermoviscoelastivity , Numerical Heat Transfer B , vol. 47 , pp. 213 – 237 , 2005 .
   Web of Science ®Google Scholar
• D. S. Choi and Y. T. Im , Prediction of Shrinkage and Warpage in Consideration of Residual Stress in Integrated Simulation of Injection Molding , Composite Structures , vol. 47 , pp. 655 – 665 , 1999 .
   Web of Science ®Google Scholar
• K. M. B. Jansen and G. Titomanlio , Effect of Pressure History on Shrinkage and Residual Stresses Injection Molding with Constrained Shrinkage , Polymer Eng. Sci. , vol. 36 , pp. 2029 – 2040 , 1996 .
   Web of Science ®Google Scholar
• D. Sun and S. V. Garimella , Numerical and Experimental Investigation of Solidification Shrinkage , Numerical Heat Transfer A , vol. 52 , pp. 145 – 162 , 2007 .
   Web of Science ®Google Scholar
• W. C. Bushko , and V. K. Stokes , Solidification of Thermoviscoelastic Melts, Part 3: Effects of Mold Surface Temperature Difference on Warpage and Residual Stresses , Polymer Eng. sci. , vol. 36 , pp. 322 – 335 , 1996 .
   Web of Science ®Google Scholar
• C. Y. Shen and H. M. Li , Numerical Simulation for Effects of Injection Mold Cooling on Warpage and Residual Stresses , Polymer-Plastics Tech. Eng. , vol. 42 , pp. 971 – 982 , 2003 .
   Web of Science ®Google Scholar
• H. Hassan , N. Regnier , C. Pujos , E. Arquis , and G. Defaye , Modeling the Effect of Cooling System on the Shrinkage and Temperature of the Polymer by Injection Molding , Appl. Therm. Eng. , vol. 30 , pp. 1547 – 1557 , 2010 .
   Web of Science ®Google Scholar
• D. Slota , Identification of the Cooling Condition in 2-D and 3-D continuous Casting Processes , Numer. Heat Transfer B , vol. 55 , pp. 155 – 176 , 2009 .
   Web of Science ®Google Scholar
• K. K. Kabanemi , H. Vallancourt , H. Wang , and G. Salloum , Residual Stresses, Shrinkage and Warpage of Complex Injection Molded Products: Numerical Simulation and Experiment Validation , Polymer Eng. Sci. , vol. 38 , pp. 21 – 37 , 1998 .
   Web of Science ®Google Scholar
• Z. Guo , X. Ruan , Y. Peng , and D. Li , Warpage of Injection-Molded Thermoplastics Parts: Numerical Simulation and Experimental Validation , J. Material Eng. Performance , vol. 11 , pp. 138 – 144 , 2001 .
   Web of Science ®Google Scholar
• H. Kurtaran , B. Ozcelik , and T. Erzurumlu , Warpage Optimization of a Bus Ceiling Lamp Base using Neural Network Model and Genetic Algorithm , J. Materials Processing Tech. , vol. 169 , pp. 314 – 319 , 2005 .
   Web of Science ®Google Scholar
• B. Ozcelik and I. Sonat , Warpage and Structural Analysis of Thin Shell Plastic in the Plastic Injection Molding , Material & Design , vol. 30 , pp. 367 – 375 , 2009 .
   Web of Science ®Google Scholar
• S. Yamaguchi , Y. W. Leong , T. Tsujii , M. Mizoguchi , U. S. Ishiaku , and H. Hamada , Effect of Crystallization and Interface Formation Mechanism on Mechacal Properties of Film-Insert Injection-Molded Poly(Propylene) (PP) Film/PP Substrate , J. Appl. Polymer Science , vol. 98 , pp. 294 – 301 , 2005 .
   Web of Science ®Google Scholar
• S. Y. Kim , H. J. Oh , S. H. Kim , C. H. Kim , S. H. Lee , and J. R. Youn , Prediction of Residual Stress and Viscoelastic Deformation of Film Insert Molded Parts , Polymer Eng. sci. , vol. 48 , pp. 1840 – 1847 , 2008 .
   Web of Science ®Google Scholar
• S. C. Chen , H. M. Li , S. T. Huang , and Y. C. Wang , Effect of Decoration Film on Mold Surface Temperature During in-Mold Decoration Injection Molding Process , Inte. Com. in Heat and Mass Transfer , vol. 37 , pp. 501 – 505 , 2010 .
   Web of Science ®Google Scholar
• J. Lee , E. Jang , S. Shin , S. Park , and H. Chung , Prediction of Residual Stress Caused by IML Process and Deformation due to Thermal Impact , Trans. KSME , vol. 34 , pp. 375 – 382 , 2010 .
   Google Scholar
• Autodesk Moldflow Insight User Manual , 2010 .
   Google Scholar