References
- K. T. McGovern and J. H. Leylek, “A detailed analysis of film cooling physics: part II—compound-angle injection with cylindrical holes,” J. Turbomach., vol. 122, no. 1, pp. 113–121, 2000. DOI:10.1115/1.555434.
- J. Liu, Z. X. Han, H. D. Jiang, J. J. Liu, and S. M. Zhou, “Experimental research on flat plate film cooling effectiveness at different complex angles,” J. Eng. Thermophys., vol. 29, pp. 1311–1315, 2008. DOI:10.3321/j.issn:0253-231X.2008.08.012.
- K. Singh, B. Premachandran, and M. R. Ravi, “Numerical investigation of film cooling on a 2D corrugated surface,”Numer. Heat Transfer. A., vol. 70, no. 11, pp. 1253–1270, 2016. DOI:10.1080/10407782.2016.1230431.
- J. Wang, P. Cui, B. Sundén, and M. Vujanović, “Effects of deposition height and width on film cooling,” Numer. Heat Transfer A., vol. 70, no. 6, pp. 673–687, 2016. DOI:10.1080/10407782.2016.1193351.
- J. Wang, P. Cui, B. Sundén, and R. Yang, “Effects of deposition locations on film cooling with and without a mist injection,” Numer. Heat Transfer A., vol. 70, no. 10, pp. 1072–1086, 2016. DOI:10.1080/10407782.2016.1230395.
- M. Gritsch, A. Schulz, and S. Wittig, “Film-cooling holes with expanded exits: near-hole heat transfer coefficients,” Int. J. Heat Fluid Flow., vol. 21, no. 2, pp. 146–155, 2000. DOI:10.1016/s0142-727x(99)00076-4.
- R. S. Bunker, “A review of shaped hole turbine film-cooling technology,” J. Heat Transfer., vol. 127, no. 4, pp. 441–453, 2005. DOI:10.1115/1.1860562.
- Y. Lu, “Effect of hole configurations on film cooling from cylindrical inclined holes for the application to gas turbine blades,” Ph.D. thesis, Louisiana State University, Baton Rouge, Louisiana, 2007.
- K. D. Lee and K. Y. Kim, “Film cooling performance of cylindrical holes embedded in a transverse trench,” Numer. Heat Transfer A., vol. 65, no. 2, pp. 127–143, 2014. DOI:10.1080/10407782.2013.826106.
- C. Han, J. Ren, and H. D. Jiang, “Multi-parameter influence on combined-hole film cooling system,” Int. J. Heat Mass Transfer., vol. 55, no. 15–16, pp. 4232–4240, 2012. DOI:10.1016/j.ijheatmasstransfer.2012.03.064.
- J. D. Heidmann and S. Ekkad, “A novel anti-vortex turbine film-cooling hole concept,” presented at ASME Turbo Expo, Montreal, 2007, GT 2007–27528. DOI:10.1115/gt2007-27528.
- H. Wu, H. H. Meng, Z. Tao, G.Q. Xu, and S.T. Ding, “Numerical investigation on the effect of different anti-vortex hole configurations on film cooling effectiveness,” J. Aerospace Power., vol. 25, pp. 2238–2243, 2010. DOI:10.13224/j.cnki.jasp.2010.10.014.
- K. Kusterer, D. Bohn, T. Sugimoto, and R. Tanaka, “Double-jet ejection of cooling air for improved film cooling,” J. Turbomach., vol. 129, no. 4, pp. 687–809, 2007. DOI:10.1115/1.2720508.
- D. W. Choi, K. D. Lee, and K. Y. Kim, “Analysis and optimization of double-jet film-cooling holes,” J. Thermophys. Heat Transfer., vol. 27, no. 2, pp. 246–254, 2013. DOI:10.2514/1.t4060.
- M. J. Ely and B. A. Jubran, “A numerical evaluation on the effect of sister holes on film cooling effectiveness and the surrounding flow field,” Heat Mass Transfer., vol. 45, no. 11, pp. 1181–1435, 2009. DOI:10.1007/s00231-009-0523-8.
- M. J. Ely and B. A. Jubran, “A parametric study on the effect of sister hole location on active film cooling flow control,” presented at ASME Turbo Expo, Glasgow, 2010, GT 2010–22060. DOI:10.1115/gt2010-22060.
- S. J. Dai, Y. Xiao, L. M. He, T. Jin, and Z. C. Zhao, “Film cooling from a cylindrical hole with parallel auxiliary holes influences,” Numer. Heat Transfer A., vol. 69, no. 5, pp. 497–511, 2016. DOI:10.1080/10407782.2015.1081023.
- T. H. Shih, W. W. Liou, A. Shabbir, Z. Yang, and J. Zhu, “A new k-[epsilon] eddy viscosity model for high reynolds number turbulent flows,” Comput. Fluids., vol. 24, no. 3, pp. 227–238, 1995. DOI:10.1016/0045-7930(94)00032-t.
- S. Khajehhasani and B. A. Jubran, “Film cooling from circular and elliptical exit shaped holes with sister hole influence,” presented at ASME Turbo Expo, San Antonio, 2013, paper no. GT 2013–95138. DOI:10.1115/gt2013-95138.
- X. Z. Zhang and I. Hassan, “Film cooling effectiveness for an advanced-louver cooling scheme for gas turbines,” J. Thermophys. Heat Transfer., vol. 20, no. 4, pp. 754–763, 2006. DOI:10.2514/1.18898.
- X. L. Zhang and C. Y. Lu, “Experimental study on flow characteristics of flat-plate single-hole film cooling,” Mech. Eng. Automation., vol. 4, pp. 8–10, 2015. DOI:10.3969/j.issn.1672-6413.2015.04.004.
- H. Wu, H. Cheng, Y. Li, C. Rong, and S. Ding, “Effects of side hole position and blowing ratio on sister hole film cooling performance in a flat plate,” Appl. Therm. Eng., vol. 93, pp. 718–730, 2016. DOI:10.1016/j.applthermaleng.2015.09.118.