References
- T. M. Pollock and S. Tin, “Nickel-based superalloys for advanced turbine engines: chemistry, microstructure and properties,” J. Propuls. Power, vol. 22, no. 2, pp. 361–374, 2006.
- R. C. Reed, The Superalloys: Fundamentals and Applications. Cambridge: Cambridge University Press, 2006.
- M. Perez, “Microstructural evolution of Nimonic 80a during hot forging under non-isothermal conditions of screw press,” J. Mater. Process. Technol., vol. 252, pp. 45–57, 2018.
- N. K. Park, I. S. Kim, Y. S. Na, and J. T. Yeom, “Hot forging of a nickel-base superalloy,” J. Mater. Process. Tech., vol. 111, no. 1–3, pp. 98–102, 2001.
- S. L. Semiatin et al., “Deformation and recrystallization behavior during hot working of a coarse-grain, nickel-base superalloy ingot material,” Metall. Mater. Trans. A, vol. 35, no. 2, pp. 679–693, 2004.
- S. L. Semiatin et al., “Microstructure evolution during supersolvus heat treatment of a powder metallurgy nickel-base superalloy,” Metall. Mater. Trans. A, vol. 43, no. 5, pp. 1649–1661, 2012.
- F. Li et al., “Impact of γ′(Ni3(Al, Ti)) phase on dynamic recrystallization of a Ni-based disk superalloy during isohot compression,” J. Alloys Compd., vol. 693, pp. 1076–1082, 2017.
- Y. Li, X. Ye, J. Li, Y. Zhang, Y. Koizumi, and A. Chiba, “Influence of cobalt addition on microstructure and hot workability of IN713C superalloy,” Mater. Design, vol. 122, pp. 340–346, 2017.
- L. M. Tan, G. A. He, Y. P. Li, F. Liu, Y. Nie, and L. Jiang, “Flow behaviors and microstructural evolutions of a novel high-Co powder metallurgy superalloy during hot working,” J. Mater. Process. Technol., vol. 262, pp. 221–231, 2018.
- L. Q. Chen, F. L. Sui, and X. H. Liu, “Grain growth model of inconel 718 alloy forged slab in reheating process prior to rough rolling,” Acta Metall. Sin., vol. 45, pp. 1242–1248, 2009.
- C. Aoki, T. Ueno, T. Ohno, and K. Oikawa, “Influence of hot-working conditions on grain growth of superalloy 718,” J. Mater. Process. Technol., vol. 267, pp. 26–33, 2019.
- P. R. Bhowal and J. J. Schirra, “Full scale gatorizing of fine grain inconel 718,” In Proceedings of Superalloys 718, 625, 706 and Various Derivatives, Warrendale, PA, 2001, pp. 193–201.
- G. He, A. Liu, F. Huang, and L. Jiang, “Analysis of forging cracks during hot compression of powder metallurgy nickel-based superalloy on simulation and experiment,” Adv. Eng. Mater., vol. 18, no. 10, pp. 1823–1832, 2016.
- G. A. He, L. M. Tan, F. Liu, L. Huang, Z. W. Huang, and L. Jiang, “Strain amount dependent grain size and orientation developments during hot compression of a polycrystalline nickel based superalloy,” Materials, vol. 10, no. 2, pp. 161, 2017.
- G. A. He, L. M. Tan, F. Liu, L. Huang, Z. W. Huang, and L. Jiang, “Unraveling the formation mechanism of abnormally large grains in an advanced polycrystalline nickel base superalloy,” J. Alloys Compd., vol. 718, pp. 405–413, 2017.
- L. Tan, Y. Li, G. He, F. Liu, Y. Nie, and L. Jiang, “Optimized hot workability of a powder metallurgy nickel-base superalloy,” Mater. Charact., vol. 147, pp. 340–352, 2019.
- H. Y. Fan, H. Jiang, J. X. Dong, Z. H. Yao, and M. C. Zhang, “An optimization method of the upsetting process for homogenized, nickel-based superalloy Udimet 720Li ingot considering both cracking and recrystallization,” J. Mater. Process. Technol., vol. 269, pp. 52–64, 2019.
- M. Gao, C. N. Reid, M. Jahedi, and Y. Li, “Estimating equilibration times and heating/cooling rates in heat treatment of workpieces with arbitrary geometry,” J. Mater. Eng. Perform., vol. 9, no. 1, pp. 62–71, 2000. DOI: 10.1361/105994900770346295.
- G. Colomer, M. Costa, R. Cònsul, and A. Oliva, “Three-dimensional numerical simulation of convection and radiation in a differentially heated cavity using the discrete ordinates method,” Int. J. Heat Mass Transf., vol. 47, no. 2, pp. 257–269, 2004.
- Z. L. Fu, X. H. Yu, H. L. Shang, Z. Z. Wang, and Z. Y. Zhang, “A new modelling method for superalloy heating in resistance furnace using FLUENT,” Int. J. Heat Mass Transf., vol. 128, pp. 679–687, 2019.
- X. Ye, Microstructure Evolution and Hot Cracking Mechanism of Inconel 718 ni-Based Uperalloy Thin-Wall Casting Component Welding Joint. Shanghai, China: Shanghai Jiaotong University, 2015.