NUMERICAL SIMULATION AND EXPERIMENTAL VERIFICATION OF MELT FRONT ADVANCEMENTS IN COINJECTION MOLDING PROCESS

REFERENCES

• E. Escales , The ICI Sandwich Molding Process , Kunststoffe , vol. 60 , pp. 847 – 852 , 1970 .
   Google Scholar
• H. Eckardt , One-Step Production of Screened Housing with Good Surface Quality Made Possible by Two-Component Injection Molding , Kunststoffe , vol. 75 , pp. 145 – 152 , 1985 .
   Google Scholar
• H. Eckardt , How to Develop a Successful Coinjection Application , Proceedings of the 14th Annual Structural Foam Conference , pp. 24 – 44 , Society of Plastics Industry , 1986 .
   Google Scholar
• K. R. Kreisher , Coinjection Molding is Hot Again—With a Lot More Going for It , Modern Plastics International , March , pp. 56 – 58 , 1990 .
   Google Scholar
• A. I. Isayev , (ed.) Injection and Compression Molding Fundamentals , Marcel Dekker , New York , 1987 .
   Google Scholar
• C. L. Tucker , (ed.) Fundamentals of Computer Modeling for Polymer Processing , Hanser Publisher , New York , 1989 .
   Google Scholar
• R. C. Donovan , K. S. Rabe , W. K. Mammel , and H. A. Load , Recycling Plastics by Two-Shot Molding , Polym. Eng. Sci. , vol. 15 , pp. 774 – 780 , 1975 .
   Google Scholar
• J. White and B. L. Lee , An Experimental Study of Sandwich Injection of Two Polymer Melts Using Simultaneous Injection , Polym. Eng. Sci. , vol. 15 , pp. 481 – 485 , 1975 .
   Web of Science ®Google Scholar
• S. S. Young , J. White , E. S. Clark , and Y. Oyangagi , A Basic Experimental Study of Sandwich Injection Molding with Sequential Injection , Polym. Eng. Sci. , vol. 20 , pp. 798 – 804 , 1980 .
   Web of Science ®Google Scholar
• L. S. Turng and K. K. Wang , Numerical Simulation of the Coinjection Molding Process , ASME J. Eng. Mat. Tech. , vol. 115 , pp. 48 – 53 , 1993 .
   Google Scholar
• M. A. Garcia , Molding of Reactive Filling in Complex Cavities , Intern. Polym. Proc. vol. 6 , pp. 73 – 82 , 1991 .
   Google Scholar
• C. A. Hieber and S. F. Shen , A Finite-Element/Finite-Difference Simulation of the Injection-Molding Filling Process , J. Non-Newtonian Fluid Mech. , vol. 7 , 1 – 32 , 1980 .
   Web of Science ®Google Scholar
• V. W. Wang , C. A. Hieber , and K. K. Wang , Dynamic Simulation and Graphics for the Injection Molding of Three-Dimensional Thin Parts , J. Polym. Eng. , vol. 7 , pp. 21 – 45 , 1986 .
   Web of Science ®Google Scholar
• S. C. Chen , P. Pai , and C. Hsu , A Study of Finite Element Mold Filling Analysis in Application , Annu. Tech. Pap. SPE , vol. 34 , pp. 250 – 254 , 1988 .
   Google Scholar
• K. F. Hsu , Numerical Simulations of Multi-Component Injection Molding Process , Master's thesis , Chung Yuan University , Taiwan , 1994 .
   Google Scholar