Characterization of In-Mold Decoration Process and Influence of the Fabric Characteristics in This Process

REFERENCES

• Menges , M. How to Make Injection Molds, 2nd Ed.; Hanser: Munich, 1993.
   Google Scholar
• Love , J.C. ; Goodship , V. In-Mold Decoration of Plastics ; Rapra Review Reports; Smithers Rapra : Shawbury , UK , 2002 .
   Google Scholar
• Osswald , T.A. International Plastics Handbook: The Resource for Plastics Engineers, 4th Ed.; Hanser: Munich, 2006.
   Google Scholar
• Stevenson , I. Innovation in Polymer Processing, Molding ; Hanser : Munich , 1996 .
   Google Scholar
• Haldenwanger , H.G. ; Vollrath , L. Plastics in Automotive Engineering ; Hanser : Munich , 1994 .
   Google Scholar
• Kazmer , D.O. Injection Mold Design Engineering ; Hanser : Munich , 2007 .
   Google Scholar
• Tucker , C.L. Computer Modelling for Polymer Processing ; Hanser : Munich , 1989 .
   Google Scholar
• Staunber , R. ; Vollrath , L. Plastics in Automotive Engineering ; Hanser : Munich , 2007 .
   Google Scholar
• Leong , Y.W. ; Hamada , H. Interfacial characteristics of film insert moldings consisting of semicrystalline and amorphous polymers . International Polymer Processing 2008 , 2 , 183 – 191 .
   Google Scholar
• Baek , S.J. ; Kim , S.Y. ; Lee , S.H. ; Youn , J.R. ; Lee , S.H. Effect of processing conditions on warpage of film insert molded parts . Fibers and Polymers 2008 , 9 , 747 – 754 .
   Google Scholar
• Chen , S.C. ; Chang , Y. ; Chang , Y.P. ; Chen , Y.C. ; Tseng , C.Y. Effect of cavity surface coating on mold temperature variation and the quality of injection molded parts . International Communications in Heat and Mass Transfer 2009 , 36 , 1030 – 1035 .
   Web of Science ®Google Scholar
• Chen , S.-C. ; Li , H.-M. ; Huang , S.-T. ; Wang , Y.C. Effect of decoration film on mold surface temperature during in-mold decoration injection molding process . International Communications in Heat and Mass Transfer 2010 , 37 , 501 – 505 .
   Web of Science ®Google Scholar
• Kennedy , P. Flow Analysis of Injection Molds ; Hanser : Munich , 1995 .
   Google Scholar
• Fernández , A. Calculation and drawing tools for design and budget of thermoplastics injection molds. Ph.D. Dissertation, Universidad de Zaragoza, UK, 2002. 1995 (in Spanish).
   Google Scholar
• Ponz , L. Method for generaton of rheological model to characterize non-conventional injection molding and its simulation tools application. Ph.D. Dissertation, Universidad de Zaragoza, Zaragoza, Spain, 2009 (in Spanish).
   Google Scholar
• Baumann , G.F. ; Steingiser , S. Rheological measurements on polycarbonate . Journal of Polymer Science 1963 , 1 , 3395 – 3406 .
   Google Scholar
• Pezzin , G. A rheological study of the injection molding of styrene polymers . Polymer Engineering & Science 1963 , 3 , 260 – 269 .
   Google Scholar
• Buchmann , M. ; Theriault , R. ; Osswald , T.A. Polymer flow length simulation during injection mold filling . Polymers Engineering & Science 1997 , 37 , 667 – 671 .
   Google Scholar
• Fox , C.W. ; Poslinski , A.J. Correlation of spiral and radial flow lengths for injection-molded thermoplastics parts . Proceeding of the Society of Plastics Engineering Annual Technical Conference 1998 , 1 , 398 – 402 .
   Google Scholar
• Rao , S. ; Ma , C. ; Schumacher , G. Predicting flow length of spiral melt flows in injection molds by semi-empirical model . Journal of Injection Molding Technology 2000 , 4 , 92 – 96 .
   Google Scholar
• Bank , D. ; Klafhen , D. ; Smierciak , R. Why plastic flows better in aluminum injection molds. Plastics Technology, 2008. Available at http://www.alcoa.com/mold/en/pdf/spiral_report.pdf (last accessed July 25, 2011).
   Google Scholar
• Liu , S.J. ; Shih , C.C. An experimental study of the water-assisted injection molding of PA-6 composites . Journal of Reinforced Plastics and Composites 2008 , 29 , 985 – 999 .
   Web of Science ®Google Scholar
• Wu , H.W. ; Zhang , S.D. Measurement and analysis of cavity pressure and melt filling capacity during injection molding . Polymer Plastic Technology and Engineering 2007 , 46 , 123 – 127 .
   Google Scholar