Insights into process innovation through ultrasonically agitated concentric flow dielectric streams for dry wire electric discharge machining

References

• Li, L.; Li, Z. Y.; Wei, X. T.; Cheng, X. Machining Characteristics of Inconel 718 by Sinking-EDM and Wire-EDM. Mater. Manuf. Proc. 2015, 30(8), 968–973.
   Web of Science ®Google Scholar
• Mandal, A.; Dixit, A. R.; Das, A. K.; Mandal, N. Modeling and Optimization of Machining Nimonic C-263 Super Alloy using Multi cut Strategy in WEDM. Mater. Manuf. Proc. 2016, 31(7), 860–868.
   Web of Science ®Google Scholar
• Azam, M.; Jahanzaib, M.; Abbasi, J. A.; Wasim, A. Modeling of Cutting Speed (CS) for HSLA Steel in Wire Electrical Discharge Machining (WEDM) Using Moly Wire. J. Chin. Inst. Eng. 2016, 39(7), 802–808.
   Web of Science ®Google Scholar
• Valaki, J. B.; Rathod, P.P. Investigating Feasibility through Performance Analysis of Green Dielectrics for Sustainable Electric Discharge Machining. Mater. Manuf. Proc. 2016, 31(4), 541–549.
   Web of Science ®Google Scholar
• Valaki, J. B.; Rathod, P. P.; Khatri, B. C. Environmental Impact, Personnel Health and Operational Safety Aspects of Electric Discharge Machining: A Review. Proc. Inst. Mech. Eng., Part B. 2015, 229(9), 1481–1491.
   Web of Science ®Google Scholar
• Furudate, C.; Kunieda, M. Study on Dry–WEDM. Proc. of 2nd Int. Conf. of MMSS’ 2000, 325–332.
   Google Scholar
• Kunieda, M.; Furudate, C. High Precision Finish Cutting by Dry WEDM. CIRP Anals– Manuf. Technol. 2001, 50(1), 121–124.
   Web of Science ®Google Scholar
• Wang, T.; Zhang, X.; Zhao, X. Study on Finishing Cut with Dry WEDM. Mater. Sci. Forum 2006, 533, 273–276.
   Google Scholar
• Takeuchi, H.; Kunieda, M. Relation Between Debris Concentration and Discharge Gap Width in EDM Process. Int. J. Electr. Mach. 2007, 12, 17–22.
   Google Scholar
• Masuzawa, T.; Cui, X.; Taniguchi, N. Improved Jet Flushing for EDM. Annals CIRP 1992, 41(1), 239–242.
   Google Scholar
• Fujimoto, T.; Okada, A.; Okamoto, Y.; Uno, Y. Optimization of Nozzle Flushing Method for Smooth Debris Exclusion in Wire EDM. Key Eng. Mater. 2012, 516, 73–78.
   Google Scholar
• Okada, A.; Konishi, T.; Okamoto, Y.; Kurihara, H. Wire Breakage and Deflection Caused by Nozzle Jet Flushing in Wire EDM. CIRP Annals – Manuf. Technol. 2015, 64(1), 233–236.
   Web of Science ®Google Scholar
• Khatri, B. C.; Rathod, P. P.; Valaki, J.B. Ultrasonic Vibration – Assisted Electric Discharge Machining: A Research Review. Proc. Inst. Mech. Eng., Part B 2016, 230(2), 319–330.
   Web of Science ®Google Scholar
• Tang, L.; Du, Y.T. Multi-Objective Optimization of Green Electrical Discharge Machining Ti–6Al–4V in Tap Water Via Grey-Taguchi Method. Mater. Manuf. Proc. 2014, 29(5), 507–513.
   Web of Science ®Google Scholar
• Kuriachen, B.; Mathew, J. Experimental Investigations into the Effects of Micro electric Discharge Milling Process Parameters on Processing Ti–6Al–4V. Mater. Manuf. Proc. 2015, 30(8), 983–990.
   Web of Science ®Google Scholar
• Shayan, A. V.; Afza, R. A.; Teimouri, R. Parametric Study Along with Selection of Optimal Solutions in Dry Wire Cut Machining of Cemented Tungsten Carbide (WC–Co). J. Manuf. Proc. 2013, 15(4), 644–658.
   Web of Science ®Google Scholar
• Teimouri, R.; Baseri, H. Experimental Study of Rotary Magnetic Field-Assisted Dry EDM With Ultrasonic Vibration of Workpiece. Int. J. Adv. Manuf. Technol. 2012, 67(5–8), 1371–1384.
   Web of Science ®Google Scholar
• Hoang, K. T.; Yang, S. H. Kerf Analysis and Control in Dry Micro–Wire Electrical Discharge Machining. Int. J. Adv. Manuf. Technol. 2015, 78(9–12), 1803–1812.
   Web of Science ®Google Scholar
• Shabgard, M. R.; Alenabi, H. Ultrasonic Assisted Electrical Discharge Machining of Ti–6Al–4V Alloy. Mater. Manuf. Proc. 2015, 30(8), 991–1000.
   Web of Science ®Google Scholar
• Zhang, Q. H.; Zhang, J. H.; Ren, S. F.; et al. Study on Technology of Ultrasonic Vibration Aided Electrical Discharge Machining in Gas. J. Mater. Proc. Technol. 2004, 149, 640–644.
   Web of Science ®Google Scholar
• Han, G.; Soo, S. L.; Aspinwall, D. K.; Bhaduri, D. Research on the Ultrasonic Assisted WEDM of Ti–6Al–4V. Adv. Mater. Res. 2013, 797, 315–319.
   Google Scholar
• Ningsong, Q.; Xiaolong, F.; Wei, L.; Yongbin, Z.; Di, Z. Wire Electrochemical Machining with Axial Electrolyte Flushing for Titanium Alloy. Chin. J. Aeronautics. 2013, 26(1), 224–229.
   Web of Science ®Google Scholar
• Khatri, B. C.; Rathod, P. P. Experimental Analysis of Concentric flow Dry Wire Electric Discharge Machining (CDWEDM). Proceedings of RK University’s First International Conference on Research & Entrepreneurship Rajkot, India, 2016 Jan 5–6, 1288–1300.
   Google Scholar
• Khan, M. A.; Rahman, M. M.; Kadirgama, K. An Experimental Investigation on Surface Finish in Die–Sinking EDM of Ti–5Al–2.5Sn. Int. J. Adv. Manuf. Technol. 2015, 77(9–12), 1727–1740.
   Web of Science ®Google Scholar
• Chalisgaonkar, R.; Kumar, J. Process Capability Analysis and Optimization in WEDM of Commercially Pure Titanium. Procedia Eng. 2014, 97, 758–766.
   Google Scholar