Advanced search
Publication Cover
Journal of the Air & Waste Management Association Volume 49, 1999 - Issue 3
Submit an article Journal homepage
478
Views
4
CrossRef citations to date
0
Altmetric
Technical Paper

Evaluation of Pollution Prevention Options to Reduce Styrene Emissions from Fiber-Reinforced Plastic Open Molding Processes

Carlos M. Nunez U.S. Environmental Protection Agency, National Risk Management Research Laboratory, Research Triangle Park, North Carolina, USACorrespondence[email protected]
,
Geddes H. Ramsey U.S. Environmental Protection Agency, National Risk Management Research Laboratory, Research Triangle Park, North Carolina, USA
,
Emery J. Kong Research Triangle Institute, Research Triangle Park, North Carolina, USA
,
Mark A. Bahner Research Triangle Institute, Research Triangle Park, North Carolina, USA
,
Robert S. Wright Research Triangle Institute, Research Triangle Park, North Carolina, USA
,
C. Andrew Clayton Research Triangle Institute, Research Triangle Park, North Carolina, USA
&
Jesse N. Baskir Research Triangle Institute, Research Triangle Park, North Carolina, USA
 show all
Pages 256-267 | Published online: 27 Dec 2011

REFERENCES

  • U.S. Environmental Protection Agency. 1987-1993 Toxics Release Inventory; EPA-749/C-95-004 (NTIS PB95-503793); U.S. Environmental Protection Agency, Office of Pollution Prevention and Toxics: Washington, DC, 1995.
  • U.S. Department of Labor, Occupational Safety and Health Administration (OSHA). Air Contaminants, Subpart Z: Toxic and Hazardous Substances; 29 CFR 1910.1000; 1993.
  • U.S. Environmental Protection Agency; Compilation of Air Pollutant Emission Factors, Volume 1: Stationary Point and Area Sources, Fifth Edition; AP-42 (NTIS PB 95-196028); Office of Air Quality Planning and Standards: Research Triangle Park, NC, 1995.
  • Felix, L.; Merritt, R.; Williamson, A. Evaluation of Styrene Emissions from a Shower Stall/Bathtub Manufacturing Facility; EPA-600/R-96-138 (NTIS PB97-125439); U.S. Environmental Protection Agency: Washington, DC, 1996.
  • Introduction to Composites; The Composites Institute of the Society of Plastics Industry, Inc.: Washington, DC, 1995.
  • Control Techniques for Organic Gas Emissions from Fiberglass Impregnation and Fabrication Processes; NTIS PB82-251109; California State Air Resources Board: Sacramento, CA, 1982.
  • Pollution Prevention Act of 1990. 42 U.S.C., Section 13101, et seq, 1990.
  • Facility Pollution Prevention Guide; EPA-600/R-92-088 (NTIS PB92-213206); U.S. Environmental Protection Agency, Office of Research and Development: Washington, DC, 1992.
  • Lacovara, R.R.; Craigie, L.; Cowley, T.; Wykowski, P.; Webster, G., Phase I - Baseline Study, Hand Lay-Up, Gel Coating, Spray-Up; Open Molding Styrene Emissions Test Project; Composites Fabricators Association: McLean, VA, 1996.
  • Schweitzer, J. Pultrusion Industry Council Phase II Emission Study; The Society of the Plastics Industry: Washington, DC, 1996.
  • Assessment of VOC Emissions from Fiberglass Boat Manufacturing; EPA-600/2-90-019 (NTIS PB90-216532); U.S. Environmental Protection Agency, Control Technology Center: Research Triangle Park, NC, 1990.
  • Guides to Pollution Prevention—The Fiberglass-Reinforced and Composite Plastics Industry; EPA/625/7-91/014 (NTIS PB91-227967); U.S. Environmental Protection Agency, Office of Research and Development: Washington, DC, 1991.
  • Hills, D.R.; Davis, A.D. Waste Reduction Strategies for Fiberglass Fabricators; East Carolina University; Prepared for Office of Waste Reduction, North Carolina Department of Environmental, Health, and Natural Resources: Raleigh, NC, 1995.
  • Evaluation of Pollution Prevention Techniques to Reduce Styrene Emissions from Open Contact Molding Processes, Volume I; EPA-600/R-97-018a (NTIS PB97-181440); U.S. Environmental Protection Agency, Office of Research and Development: Washington, DC, 1997.
  • Code of Federal Regulations, Title 40, Part 60, Appendix A.

Reprints and Corporate Permissions

Please note: Selecting permissions does not provide access to the full text of the article, please see our help page How do I view content?

To request a reprint or corporate permissions for this article, please click on the relevant link below:

Order Reprints Request Corporate Permissions

Academic Permissions

Please note: Selecting permissions does not provide access to the full text of the article, please see our help page How do I view content?

Obtain permissions instantly via Rightslink by clicking on the button below:

Request Academic Permissions

If you are unable to obtain permissions via Rightslink, please complete and submit this Permissions form. For more information, please visit our Permissions help page.

Related research

People also read lists articles that other readers of this article have read.

Recommended articles lists articles that we recommend and is powered by our AI driven recommendation engine.

Cited by lists all citing articles based on Crossref citations.
Articles with the Crossref icon will open in a new tab.