References
- H. Tanaka, T. Sugihara, and T. Enomoto, High Speed Machining of Inconel 718 Focusing on Wear Behaviors of PCBN Cutting Tool, Procedia CIRP 46, 545 (2016). DOI: https://doi.org/10.1016/j.procir.2016.03.120.
- A. Maryam, M. Saharnaz, and S. C. Veldhuis, A novel treatment for cutting tools for reducing the chipping and improving tool life during machining of Inconel 718, Wear 414–415, 79 (2018). DOI: https://doi.org/10.1016/j.wear.2018.08.002.
- A. Mama, B. Aia, and A. Anmk, Specific cutting energy of Inconel 718 under dry, chilled-air and minimal quantity nanolubricants, Procedia CIRP 77, 429 (2018).
- Y. Hua, and Z. Liu, Effects of cutting parameters and tool nose radius on surface roughness and work hardening during dry turning Inconel 718, Int. J. Adv. Manuf. Technol. 96 (5–8), 2421 (2018). DOI: https://doi.org/10.1007/s00170-018-1721-7.
- X. Ren, and Z. Liu, Influence of cutting parameters on work hardening behavior of surface layer during turning superalloy Inconel 718, Int. J. Adv. Manuf. Technol. 86 (5–8), 2319 (2016). DOI: https://doi.org/10.1007/s00170-016-8350-9.
- M. Klaus, C. Genzel, and H. Holzschuh, Residual stress depth profiling in complex hard coating systems by X-ray diffraction, Thin Solid Films 517 (3), 1172 (2008). DOI: https://doi.org/10.1016/j.tsf.2008.05.018.
- Z. T. Tang et al., The influence of tool flank wear on residual stresses induced by milling aluminum alloy, J. Mater. Process Technol. 209 (9), 4502 (2009). DOI: https://doi.org/10.1016/j.jmatprotec.2008.10.034.
- S. Deville, J. Chevalier, and L. Gremillard, Influence of Surface Finish and Residual Stresses on the ageing sensitivity of biomedical grade zirconia, Biomaterials 27 (10), 2186 (2006). DOI: https://doi.org/10.1016/j.biomaterials.2005.11.021.
- Z. H. Long, W. X. Zhao, and X. B. Wang, Experimental research on surface reinforcement mechanism introduced by coupling effect of cutting forces and heat, J. Aeronaut. Mater. 27, 45 (2007).
- M. Xin et al., Study on the Surface Residual Stress of High Hardness and Strength Alloy Steel in High Speed Milling, Trans. Beijing Inst. Technol. 30, 19 (2010).
- X. Zhang et al., Predicting the Effects of Cutting Parameters and Tool Geometry on Hard Turning Process Using Finite Element Method, J. Manuf. Sci. Eng. 133, 041010 (2011).
- D. Ulutan, B. E. Alaca, and I. Lazoglu, Analytical modelling of residual stresses in machining, J. Mater. Process Technol. 183 (1), 77 (2007). DOI: https://doi.org/10.1016/j.jmatprotec.2006.09.032.
- I. Lazoglu et al., An enhanced analytical model for residual stress prediction in machining, CIRP Ann. Manuf. Technol. 57 (1), 81 (2008). DOI: https://doi.org/10.1016/j.cirp.2008.03.060.
- S. Y. Liang, and J. C. Su, Residual Stress Modeling in Orthogonal Machining, CIRP Ann. –Manuf. Technol. 56 (1), 65 (2007). DOI: https://doi.org/10.1016/j.cirp.2007.05.018.
- Achieving machining residual stresses through model-driven planning of process parameters.//NAMRC 36;North American Manufacturing Research Conference. George W. Woodruff School of Mechanical Engineering Georgia Institute of Technology Atlanta, Georgia, USA; Department of System and Naval Mechatronics, 2008.
- S. Jeelani, and J. A. Bailey, Residual Stress Distribution in Machining Annealed 18 Percent Nickel Maraging Steel, J. Eng. Mater. Technol. 108 (2), 93 (1986). DOI: https://doi.org/10.1115/1.3225865.
- A. D. He, Investigation on Processing Mechanism and Control of Residual Stress in Cmql Machining (South China University of Technology, Guangzhou 2018).
- G. S. Su et al., Effects of high-pressure cutting fluid with different jetting paths on tool wear in cutting compacted graphite iron, Tribol. Int. 103, 289 (2016). DOI: https://doi.org/10.1016/j.triboint.2016.06.029.
- X. Li, Study of the jet-flow rate of cooling in machining Part 2. Simulation study, J. Mater. Process Technol. 62 (1–3), 157 (1996). DOI: https://doi.org/10.1016/0924-0136(95)02198-1.
- S. Kaldor, A. Ber, and E. Lenz, On the mechanism of chip breaking, J. Manuf. Sci. Eng. 101 (3), 241 (1979). DOI: https://doi.org/10.1115/1.3439503.
- J. L. Yan, X. F. Yu, and Y. Q. Wang, Chart of Thermodynamic Properties of Water and Steam (China Electric Power Press, Beijing, 2004).
- Y. C. Zheng, Research on Machining Performance and Experiment in Turning Difficult to Machine Materials with High Pressure Cooling (Harbin University of Science and Technology, Harbin 2015).
- I. A. Choudhury, and M. A. Ei-Baradie, Machinability of nickel-base super alloys: a general review, J. Mater. Process. Technol. 77 (1–3), 278 (1998). DOI: https://doi.org/10.1016/S0924-0136(97)00429-9.
- N. Xiao, H. J. Wu, and H. C. Xie, Measurement of residual stress in cast bearing by X-ray, Mech. Eng. Autom. 1, 138 (2015).