Multipoint cure monitoring of temperature and strain of carbon fibre-reinforced plastic shafts using fibre Bragg grating sensors

References

• Chehura E, James SW, Tatam RP. Multiplexed fibre optic sensors for monitoring resin infusion, flow, and cure in composite material processing[C]//smart sensor phenomena, technology, networks, and systems integration. Inter Soc Optics Photonics. 2013;8693:86930F. DOI：10.1117/12.2012214
   Google Scholar
• Ramakrishnan M, Rajan G, Semenova Y, et al. Overview of fiber optic sensor technologies for strain/temperature sensing applications in composite materials. Sensors. 2016;16(1):99. DOI：10.3390/s16010099
   PubMed Web of Science ®Google Scholar
• Jia X, Chen G, Yu Y, et al. Effect of geometric factor, winding angle and pre-crack angle on quasi-static crushing behavior of filament wound CFRP cylinder. Compos Part B Eng. 2013;45(1):1336–1343.
   Web of Science ®Google Scholar
• Yefa H, Jin Y, Jinguang Z, et al. Material design and failure experiment of a carbon fibre reinforced plastics drive shaft. Mater Res Innovations. 2015;19(S5):S5-458-S5-463.
   Google Scholar
• Sdol E. Composites science and technology[M]//composites science and technology. Amsterdam: Elsevier Applied Science Publishers; 1985.
   Google Scholar
• Koo JM, Choi JH, Seok CS. Prediction of post-impact residual strength and fatigue characteristics after impact of CFRP composite structures. Compos Part B Eng. 2014;61:300–306.
   Web of Science ®Google Scholar
• Lee DG, Kim HS, Kim JW, et al. Design and manufacture of an automotive hybrid aluminum/composite drive shaft. Compos Struct. 2004;63(1):87–99.
   Web of Science ®Google Scholar
• De Oliveira R, Lavanchy S, Chatton R. Experimental investigation of the mould thermal expansion on the development of internal stresses during carbon fiber composite processing. Compos Part A Appl Sci Manuf. 2008;39(7):1083–1090.
   Web of Science ®Google Scholar
• Antonucci V, Cusano A, Giordano M, et al. Cure-induced residual strain build-up in a thermoset resin. Compos Part A Appl Sci Manuf. 2006;37(4):592–601.
   Web of Science ®Google Scholar
• Messager T, Pyrz M, Gineste B, et al. Optimal laminations of thin underwater composite cylindrical vessels. Compos Struct. 2002;58(4):529–537.
   Web of Science ®Google Scholar
• Li HN, Zhou GD, Liang R, et al. Strain transfer analysis of embedded fiber Bragg grating sensor under nonaxial stress. Opt Eng. 2007;46(5):054402.
   Web of Science ®Google Scholar
• Luyckx G, Voet E, Lammens N, et al. Strain measurements of composite laminates with embedded fibre Bragg gratings: criticism and opportunities for research. Sensors. 2011;11(1):384–408.
   PubMed Web of Science ®Google Scholar
• Kinet D, Mégret P, Goossen K, et al. Fiber Bragg grating sensors toward structural health monitoring in composite materials: challenges and solutions. Sensors. 2014;14:7394–7419.
   PubMed Web of Science ®Google Scholar
• Lammens N, Kinet D, Chah K, et al. Residual strain monitoring of out-of-autoclave cured parts by use of polarization dependent loss measurements in embedded optical fiber Bragg gratings. Compos Part A Appl Sci Manuf. 2013;52(52):38–44.
   Google Scholar
• Minak G, Ghelli D. Influence of diameter and boundary conditions on low velocity impact response of CFRP circular laminated plates. Compos Part B Eng. 2008;39(6):962–972.
   Web of Science ®Google Scholar
• Kosaka T, Osaka K, Sando M, et al. Health monitoring of FW molded GFRP by using FBG sensors. Japan: The Japan Society of Mechanical Engineers; 2003. p. 1019–1020.
   Google Scholar
• Stringer LG, Hayman RJ, Hinton MJ, et al. Curing stresses in thick polymer composite components. Part II: Management of residual stresses. France (Paris): Proceedings of Iccm; 1999. p. 1–10.
   Google Scholar
• Colpo F, Humbert L, Botsis J. Characterisation of residual stresses in a single fibre composite with FBG sensor. Compos Sci Technol. 2007;67(9):1830–1841.
   Web of Science ®Google Scholar
• Hernandez Moreno H, Collombet F, Douchin B, et al. Entire life time monitoring of filament wound composite cylinders using Bragg grating sensors I. Adapted tooling and instrumented specimen. Appl Compos Mater. 2009;16:173–182.
   Google Scholar
• Hernande Moreno H, Collombet F, Douchin B, et al. Entire life time monitoring of filament wound composite cylinders using Bragg grating sensors II. Process monitoring. Appl Compos Mater. 2009;16:197–209.
   Google Scholar
• Hernandez Moreno H, Collombet F, Douchin B, et al. Entire life time monitoring of filament wound composite cylinders using Bragg grating sensors III. In-service external pressure loading. Appl Compos Mater. 2009;16:135–147.
   Google Scholar
• Casari P, Jacquemin F, Davies P. Characterisation of residual stresses in wound composites. Compos Part A. 2006;37(2):337–343.
   Web of Science ®Google Scholar
• Takagaki K, Minakuchi S, Takeda N. Fiber-optic-based life-cycle monitoring of through-thickness strain in thick CFRP pipes. Adv Compos Mater. 2014;23(3):195–209.
   Web of Science ®Google Scholar
• Takagaki K, Shu M, Takeda N. Thick-walled crack-free CFRP pipes: stress reduction using atypical lay-up. Compos Struct. 2015;126(1):337–346.
   Google Scholar
• Marcelo M, Allil RCSB, Bessie A, et al. A guide to fiber Bragg grating sensors[M]//current trends in short- and long-period fiber gratings. London: IntechOpen publishers; 2013.
   Google Scholar