References
- K. Nakayama , “ A Study on the Chip Breaker ,” Bull. Jap. Soc. Prec. Eng. , 5 ( 17 ) ( 1962 ) 142.
- K. Nakayama , “ Chip Curl in Metal Cutting Process, ” Bull. Faculty of Eng. , Yokohama National Univ., 11 ( 1962 ) 1.
- K. Nakayama , “ Chip Control in Metal Cutting ,” Bull. Jap. Soc. Prec. Eng. , 18 ( 2 ) ( 1984 ) 97.
- K. Nakayama , “ Origins of Side Curl of Chip in Metal Machining ,” Bull. Jap. Soc. of Prec. Eng. , 6 ( 3 ) ( 1972 ) 99.
- N. H. Cook , P. Jhaveri , and N. Nayak , “ The Mechanism of Chip Curl and Its Importance in Metal Cutting ,” Trans. ASME , ( 1963 ) 374.
- A. J. Pekelharing , “ Why and How Does the Chip Curl and Break ,” Annals of CIRP , 12 ( 1 ) ( 1964 ) 144.
- G. R. Ponkshe , “ A New Explanation of the Phenomenon of Chip Curling During Machining ,” Trans. ASME , 66-Prod-E ( 1967 ) 376 .
- C. Spaans , “ The Fundamentals of Three-dimensional Chip-curl, Chip Breaking and Chip Control ,” Doctoral Thesis , TH Delft ( 1971 ).
- C. Spans , and P. F. H.J. van Geel . “ Break Mechanisms in Cutting with a Chip Breaker ,” Annals of CIRP , 18 ( 1 ) ( 1970 ) 87 .
- B. Worthington , and A. H. Redford , “ Chip Curl and the Action of the Groove Type Chip Former ,” Int. J. of Mach. Tool Des. Res. , 13 ( 1973 ) 257 .
- B. Worthington , and M. H. Rahman , “ Predicting Breaking with Groove Type Breakers ,” Intl. J. of Mach. Tool Des. and Res. , 19 ( 1979 ) 121 .
- A. B. Walton and B. Worthington , “ The Performance of Cutting Tools with Unusual Forms ,” Int. J. of Mach. Toot Des. and Res. , 21 ( 1980 ) 411 .
- I. S. Jawahir and C. A. van Luttervelt , “ Recent Developments in Chip Control Research and Applications ,” Keynote paper, Annals of CIRP , 42 ( 2 ) ( 1993 ) 659 .
- I. S. Jawahir , “ The Tool Restricted Contact Effect as a Major Influencing Factor in Chip Breaking: An Experimental Analysis ,” Annals of CIRP , 37 ( 1 ) ( 1988 ) 121 .
- I. S. Jawahir , “On the Controllability of Chip Breaking Cycles and Modes of Chip Breaking in Metal Machining,” Annals ofCIRP , 39 (1) (1990) 47.
- I. S. Jawahir , and P. L. B. Oxley , “ New Developments in Chip Control Research: Moving Towards Chip Breakability Predictions for Unmanned Manufacture, ” Proc. Int. Conf. , ASME, Atlanta ( 1988 ) 311 .
- I. S. Jawahir and J. Zhang , “ An Analysis of Chip Curl Development, Chip Deformation and Chip Breaking in Orthogonal Machining ,” Trans. NAMRI , 23 ( 1995 ) 109 .
- P. Albrecht , “ New Development in the Theory of Metal Cutting Process ,” Trans. ASME , B 83-4 ( 1961 ) 557 .
- E. H. Lee , and B. W. Shaffer , “ The Theory of Plasticity Applied to a Problem of Machining ,” Trans. ASME , B-73 ( 1951 ) 405 .
- R. S. Hahn , “ Some Observations on Chip Curl in the Metal Cutting Process Under Orthogonal Cutting Conditions ,” Trans. ASME , B-75 ( 1953 ) 581 .
- E. Lenz , and M. Y. Friedman , “ Tool-chip Contact Length as a Parameter in Metal Cutting ,” ASME Meeting, Sept. , ( 1968 ).
- H. Kudo , “ Some New Slip-line Solutions for Two-dimensional Steady-state Machining ,” Int. J. Mech. Sci. , 7 ( 1965 ) 43 .
- P. Dewhurst , “ On the Non-uniqueness of the Machining Process, ” Proc. Roy. Soc , London , A-360 ( 1978 ) 587 .
- T. H. C. Childs , “ Elastic Effects in Metal Cutting Chip Formation ,” Int. J. Mech. Sci. , 22 ( 1980 ) 457 .
- T. Shi , and S. Ramalingam , “ Modeling Chip Formation with Grooved Tools ,” Int. J. Mech. Sci. , 35 ( 9 ) ( 1993 ) 741 .
- B. Venkatraman , and S. Patel , Structural Mechanics with Introductions to Elasticity and Plasticity , McGraw Hill, NY ( 1970 ).
- F. B. Seely and J. O. Smith , Advanced Mechanics of Materials , 2nd ed., John Wiley & Sons, London ( 1952 ).
- S. Kaldor , A. Ber , and E. Lenz , “ On the Mechanism of Chip Breaking ,” Trans. ASME , 101 ( 1979 ) 241 .
- A. Ber , S. Kaldor , and E. Lenz , “ New Concept in Chip Breaker Design Leads to a Wider Range of Chip Breaking ,” SME Technical Paper , MR 79–307 ( 1979 ).
- C. Nedess , and W. Hintze , “ Characteristic Parameters of Chip Control in Turning Operations with Indexable Three-dimensionally Shaped Chip Formers ,” Annals of CIRP , 38 ( 1 ) ( 1989 ) 75 .