AN INVESTIGATION OF 3-D CURLED CHIP IN MACHINING-PART 2: SIMULATION AND VALIDATION USING FE TECHNIQUES

References

• R. Ghosh , O. W. Dillon Jr. , and I. S. Jawahir , “ An Investigation of 3-D Cud Chip in Machining-Part 1: A Mechanics-based Analytical Model, ” Machining Science and Technology , 2 ( 1 ) ( 1998 ) 91 – 116 .
   Web of Science ®Google Scholar
• A. O. Tay , “ A Numerical Study of the Temperature Distribution Generated During Orthogonal Machining, ” Ph. D. Thesis , Univ. of New South Wales, Australia , 1973 .
   Google Scholar
• A. O. Tay , M. G. Stevenson , and G. de V. Davis, “Using the Finite Element Method to Determine Temperature Distributions in Orthogonal Machining,” Proc. Inst. Mech. Eng. , 188 (1974) 627.
   Google Scholar
• B. E. Klamecki , “ Incipient Chip Formation in Metal Cutting A Three dimensional Finite Element Analysis, ” Ph.D. Dissertation , Univ. of Illinois, Urbana Champaign , 1973 .
   Google Scholar
• M. G. Stevenson , P. K. Wright , and J. G. Chow , “ Further Developments in Applying the Finite Element Method to the Calculation of Temperature Distributions in Machining and Comparisons with Experiment ,” J. of Eng. for Indust. , 105 ( 1983 ) 149 .
   Web of Science ®Google Scholar
• K. Iwata , K. Osakada , and Y. Teresaka , “ Process Modeling of Orthogonal Cutting by the Rigid-plastic Finite Element Method ,” Trans. ASME , 106 ( 1984 ) 132 .
   Google Scholar
• J. S. Strenkowski and J. T. Carroll , “ A Finite Element Model of Orthogonal Metal Cutting ,” J. of Eng. for Indust. , 107 ( 1985 ) 349 .
   Google Scholar
• P. Jain , “ Finite Element Analysis of Machining, ” M. S. Thesis , Univ. of Kentucky, 1985 .
   Google Scholar
• K. F. Eldridge , “ On the Mechanics of Orthogonal Machining, ” M. S. Thesis , Univ. of Kentucky, 1990 .
   Google Scholar
• J. S. Strenkowski , and K. J. Moon , “ Finite Element Prediction of Chip Geometry and Tool/Workpiece Temperature Distributions in Orthogonal Metal Cutting, ” J. of Eng. for Indust. , 112 ( 1990 ) 313 .
   Web of Science ®Google Scholar
• K. Komvopoulos , and S. A. Erpenbeck , “ Finite Element Modeling of Orthogonal Metal Cutting ,” J. of Eng. for Indust. , 113 ( 1991 ) 253 .
   Google Scholar
• J. S. Wu , O. W. Dillon , and W. Y. Lu , “ Thermo-viscoplastic Modeling of Machining Process Using a Mixed Finite Element Method ,” J. of Mfg. Sc. and Eng., ASME , 118 ( 1996 ) 470 .
   Web of Science ®Google Scholar
• A. J. Shih , S. Chandrasekar , and H. T. Yang , “ Finite Element Simulation of Metal Cutting Process with Strain Rate and Temperature Effects ,” Fundamental Issues in Machining, PED, ASME , 43 ( 1990 ) 11 .
   Google Scholar
• K. Ueda and K. Manabe , “ Rigid-plastic FEM Analysis of Three-dimensional Deformation Field in Chip Formation Process ,” Annals of the CIRP , 42 ( 1 ) ( 1993 ) 35 .
   Google Scholar
• B. Zhang and A. Bagchi , “ Finite Element Simulation of Chip Formation and Comparison with Machining Experiment ,” J. of Eng. for Indust. , 116 ( 1994 ) 289 .
   Web of Science ®Google Scholar
• T. D. Marusich and M. Ortiz , “ Modeling and Simulation of High-speed Machining ,” Int. J. Num. Methods Eng. , 38 ( 1995 ) 3675 .
   Web of Science ®Google Scholar
• I. S. Jawahir , and J. P. Zhang , “ An Analysis of Chip Curl Development, Chip Deformation and Chip Breaking in Orthogonal Machining ,” Trans. NAMRI , 23 ( 1995 ) 109 .
   Google Scholar
• K. Maekawa , I. Ohshima , and R. Murata , “ Finite Element Analysis of Temperature and Stresses within an Internally Cooled Cutting Tool ,” Bull. Jap. Soc. Prec. Eng. , 23 ( 3 ) ( 1989 ) 243 .
   Google Scholar
• J. S. Strenkowski and G. D. Hiatt , “ A Technique for Predicting the Ductile Regime in Single Point Diamond Turning of Brittle Materials ,” Fundamental Issues in Machining, PED, ASME , 43 ( 1990 ) 67 .
   Google Scholar
• V. S. Joshi , P. M. Dixit , and V. K. Jain , “Viscoplastic Analysis of Metal Cutting by Finite Element Method,” Int. J. Mack Tools Manufact. , 34 (4) (1994) 553.
   Web of Science ®Google Scholar
• J. A. Yang , “ A Predictive Model of Chip Breaking for Groove Type Tools in Orthogonal Machining of AISI 1020 Steel, ” Ph.D. Thesis , N. C. State Univ., Raleigh , 1992 .
   Google Scholar
• S. M. Athavale , “ A Damage-based Model for Predicting Chip Breakability for Obstruction and Grooved Tools, ” Ph.D. Thesis , N. C. State Univ., Raleigh , 1994 .
   Google Scholar
• S. F. Wayne , D. A. Oneil and C. Zimmerman , “ An Expert System for Design, Analysis and Production of Cutting Tools, ” Proc. HMP 92 , Bonn , Germany , May 1992 .
   Google Scholar
• ANSYS User's Manual, 5.0, Swanson Analysis Systems.
   Google Scholar
• B. K. Ganapathy , and I. S. Jawahir , “ A Force Model for Chip Breaking in Orthogonal Machining ,” PED,ASME , 64 ( 1993 ) 461 .
   Google Scholar
• I. S. Jawahir , R. Ghosh , X. D. Fang , and P. X. Li , “ An Investigation of the Effects of Chip Flow on Tool Wear in Machining with Complex Grooved Tools ”, Wear , 184 ( 1995 ) 145 .
   Web of Science ®Google Scholar
• I. S. Jawahir , “ On the Controllability of Chip Breaking Cycles and Modes of Chip Breaking in Metal Machining ”, Annals of the CIRP , 39 ( 1 ) ( 1990 ) 47 .
   Google Scholar