Design and optimisation of die casting process for heavy-duty automatic transmission oil circuit board

References

• Jian-liang PAN, Yan MENG. Comparison among several transmission techs. Automob Parts. 2008;44:40–41.
   Google Scholar
• Wenqian H. Production of Aluminum Alloy Oil Circuit Board by Low Pressure Casting. Special Cast Nonferrous Alloys. 2015;5:1284–1285.
   Google Scholar
• Fabrizi A, Ferraro S, Timelli G. The influence of Sr, Mg and Cu addition on the microstructural properties of a secondary AlSi9Cu3(Fe) die casting alloy. Mater Charact. 2013;85:13–25.
   Web of Science ®Google Scholar
• Ji S, Yan F, Fan Z. Development of a high strength Al–Mg2Si–Mg–Zn based alloy for high pressure die casting. Mater Sci Eng A. 2015;626:165–174.
   Web of Science ®Google Scholar
• Dargusch MS, Dour G, Schauer N, et al. The influence of pressure during solidification of high pressure die cast aluminium telecommunications components. J Mater Process Technol. 2006;180(1–3):37–43.
   Web of Science ®Google Scholar
• Gunasegaram DR, Givord M, O’Donnell RG, et al. Improvements engineered in UTS and elongation of aluminum alloy high pressure die castings through the alteration of runner geometry and plunger velocity. Mater Sci Eng A. 2013;559:276–286.
   Web of Science ®Google Scholar
• Sharifi P, Jamali J, Sadayappan K, et al. Quantitative experimental study of defects induced by process parameters in the high-pressure die cast process. Metall Mater Trans A. 2018;49(7):3080–3090.
   Google Scholar
• Qin X-Y, Yong S, Chen J, et al. Finite element analysis for die casting parameters in high-pressure die casting process. China Foundry. 2019;16(4):272–276.
   Web of Science ®Google Scholar
• Rai Jitender K, Lajimi Amir M, Paul X. An intelligent system for predicting HPDC process variables in interactive environment. J Mater Process Technol. 2007;203:72–79.
   Web of Science ®Google Scholar
• Lee SG, Gokhale AM, Patel GR, et al. Effect of process parameters on porosity distributions in high-pressure die-cast AM50 Mg-alloy. Mater Sci Eng A. 2006;427(1–2):99–111.
   Web of Science ®Google Scholar
• Kim ES, Park JY, Kim YH, et al. Evaluation of die casting mold cooling ability by decompression cooling system. J Korea Foundry Soc. 2009;29:238–243.
   Google Scholar
• Otsuka Y. Experimental verification and accuracy improvement of gas Entrapment and shrinkage porosity simulation in high pressure die casting process. Mater Trans. 2014;55(1):154–160.
   Web of Science ®Google Scholar
• Chen H, Lu W. Design of die casting process of top cover of automobile generator through numerical simulations and its experimental validation. Int J Cast Met Res. 2011;24:163–169.
   Web of Science ®Google Scholar
• Erturk. SO, Kumruoglu LC, Ozel.A A. simulation and fabrication works on optimization of high pressure aluminum die casting part. Acta Phys Pol A. 2014;2(2):449–451.
   Google Scholar
• Katzarov IH. Finite element modeling of the porosity formation in castings. Int J Heat Mass Transfer. 2003;46(9):1545–1552.
   Web of Science ®Google Scholar
• Faura F, López J, Hernández J. On the optimum plunger acceleration law in the slow shot phase of pressure die casting machines. Int J Mach Tools Manuf. 2001;41(2):173–191.
   Web of Science ®Google Scholar
• Prasad KDVY, Chiang ECW. A neural network system for the prediction of process parameters in pressure die casting. J Mat Process Technol. 1999;89:583–590.
   Google Scholar
• Verran GO, Mendes RPK, Dalla Valentina LVO. DOE applied to optimization of aluminum alloy die castings. J Mater Process Technol. 2007;200(1–3):120–125.
   Web of Science ®Google Scholar
• Hu BH, Tong KK, Niu XP, et al. Design and optimisation of runner and gating systems for the die casting of thin-walled magnesium telecommunication parts through numerical simulation. J Mater Process Technol. 2000;105(1–2):128–133.
   Web of Science ®Google Scholar
• Murat T. Pore size distributions in AM50 Mg alloy die castings. Mater Sci Eng A. 2007;465(1–2):287–289.
   Web of Science ®Google Scholar
• Tsoukalas VD. Optimization of injection conditions for a thin-walled die-cast part using a genetic algorithm method. J Eng Manuf. 2008;222(9):1097–1106.
   Google Scholar
• Nongcun SHUAI, Zecai SHAO. 5G base station energy consumption model based on multiple linear regression algorithm. Mobile Commun. 2020;44:32–36+41.
   Google Scholar
• Liang L, Guang-ming Y, Chen Z-Y, et al. Discontinuous flying particle swarm optimization algorithm and its application to slope stability analysis. J Cent South Univ Technol. 2010;17(4):852–856.
   Web of Science ®Google Scholar