References
- Bhushan, R. K., Sudhir, K. & Das, S. 2009, “Optimisation of porosity of 7075 Al alloy 10% SiC composite produced by stir casting process through Taguchi method”, Int. J. Materials Engineering Innovation, Vol. 1, No. 1, pp. 116–129.
- Ganapathy, T., Murugesan, K. & Gakkhar, R. P. 2009, “Performance optimization of Jatropha biodiesel engine model using Taguchi approach”, Applied Energy, Vol. 86, pp. 2476–2486.
- Hsiang, S. H. & Lin, Y. W. 2007, “Investigation of influence of process parameters on hot extrusion of magnesium alloy tubes”, J. of Mat. Proc. Tech., No. 192–193, pp. 292–299.
- Japan Aluminium Association, 1990, JIS H 4090:1990 Aluminium and aluminium alloy welded pipes and tubes.
- Jiang, B., Gao, L., Huang, G., Ding, P. & Wang, J. 2008, “Effect of extrusion processing parameters on microstructure and mechanical properties of as-extruded AZ31 sheets”, Trans. Nonferrous Met. Soc. China, Vol. 18, pp. 160–164.
- Jo, H. H., Lee, S. K., Jung, C. S. & Kim, B. M. 2006, “A non steady state FE analysis of Al tubes hot extrusion by a porthole-die”, J. of Mat. Proc. Tech., Vol. 173, pp. 223–231.
- Kim, K. J., Lee, C. H. & Yang, D. Y. 2002, “Investigation into the improvement of welding strength in three dimensional extrusion of tubes using porthole-die”, J. of Mat. Proc. Tech., No. 130–131, pp. 426–431.
- Lee, H. H. 2000, Taguchi methods: Principles and practices of quality design, Gaulih Book Co. Ltd., Taiwan.
- Lee, G. A. & Im, Y. T. 2002, “Analysis and design of flat-die hot extrusion process – Numerical design of bearing length”, Int. J. Mech. Sci., Vol. 44, pp. 935–946.
- Lee, G. A., Kwak, D. Y., Kim, S. Y. & Im, Y. T. 2002, “Analysis and design of flat-die hot extrusion process – Three dimensional finite element analysis”, Int. J. Mech. Sci., Vol. 44, pp. 915–934.
- Lee, J. M., Kim, B. M. & Kang, C. G. 2005, “Effects of chamber shapes of porthole-die on elastic deformation and extrusion process in condenser tube extrusion”, Materials and Design, Vol. 26, pp. 327–336.
- Li, L., Zhou, J. & Duszczyk, J. 2004, “Prediction of temperature evolution during the extrusion of 7075 Aluminium-alloy at various ram speeds by means of 3D FEM simulation”, J. of Mat. Proc. Tech., Vol. 145, pp. 360–370.
- Peng, Z. & Sheppard, T. 2004, “Simulation of multi hole die extrusion”, Mat. Sci. Engg, Vol. 367, pp. 329–342.
- Ross, P. J. 1988, Taguchi techniques for quality engineering, McGraw-Hill, New York.
- Sahin, B., Yakut, K., Kotiioglu, I. & Celik, C. 2005, “Optimum design parameters of a heat exchanger”, Applied Energy, Vol. 82, pp. 90–106.
- Takahashi, H., Murakami, T. & Xie, J. X. 1990, “Determination of welding pressure in the non-steady-state porthole die extrusion of improved Al7003 hollow section tubes”, Advance Technol. Plasticity, Vol. 14, pp. 323–328.
- Ulysse, P. A. & Johnson, R. E. 1998, “A study of the effect of the process variables in un-symmetrical single hole and multi-hole extrusion processes”, J. of Mat. Proc. Tech., Vol. 73, pp. 213–225.
- Wang, S. T., Lee, R. S., Li, H. Y. & Chen, C. H. 2006, “Optimal die design for three-dimensional porthole extrusion using the Taguchi method”, Proc. IMechE Part B: J. Engineering Manufacture, Vol. 220, pp. 1005–1009.
- Yakut, K., Alemdaroglu, N., Sahin, B. & Celik, C. 2006, “Optimum design parameters of a heat exchanger having hexagonal fins”, Applied Energy, Vol. 83, pp. 82–98.