Fabrication of AZ91D/SiCp composites by mechanical milling of magnesium alloy chips and spark plasma sintering in a semi-solid regime

References

• Hirt G, Kopp R, editors. Thixoforming: semi-solid metal processing. Weinheim: John Wiley & Sons; 2009.
   Google Scholar
• Guo MT, Tsao CY. Tribological behavior of self-lubricating aluminium/SiC/graphite hybrid composites synthesized by the semi-solid powder-densification method. Compos Sci Technol. 2000;60:65–74.
   Web of Science ®Google Scholar
• Li T, Lin X, Huang W. Preparation of metal alloy powder by semi-solid processing. J Mater Sci. 2007;42:2669–2674.
   Web of Science ®Google Scholar
• Javdani A, Pouyafar V, Ameli A, et al. Blended powder semisolid forming of Al7075/Al2O3 composites: investigation of microstructure and mechanical properties. Mater Des. 2016;109:57–67.
   Web of Science ®Google Scholar
• Plookphol T, Wisutmethangoon S, Gonsrang S. Influence of process parameters on SAC305 lead-free solder powder produced by centrifugal atomization. Powder Technol. 2011;214:506–512.
   Web of Science ®Google Scholar
• Liu Y, Niu S, Li F, et al. Preparation of amorphous Fe-based magnetic powder by water atomization. Powder Technol. 2011;213:36–40.
   Web of Science ®Google Scholar
• Kim KH, Lee YB, Choi EY, et al. Synthesis of nickel powders from various aqueous media through chemical reduction method. Mater Chem Phys. 2004;86:420–424.
   Web of Science ®Google Scholar
• Varol T, Canakci A. Effect of weight percentage and particle size of B4C reinforcement on physical and mechanical properties of powder metallurgy Al2024- B4C composites. Met Mater Int. 2013;19:1227–1234.
   Web of Science ®Google Scholar
• Canakci A, Erdemir F, Varol T, et al. Determining the effect of process parameters on particle size in mechanical milling using the Taguchi method: measurement and analysis. Measurement. 2013;46:3532–3540.
   Web of Science ®Google Scholar
• Canakci A, Varol T, Ozsahin S. Analysis of the effect of a new process control agent technique on the mechanical milling process using a neural network model: measurement and modeling. Measurement. 2013;46:1818–1827.
   Web of Science ®Google Scholar
• Oginuma H, Yuasa E. Crystal structure formed in mechanical alloying process of Mg-Al-Zn powder mixture using magnesium alloy machined chips. JSME Int J Ser A Solid Mech Mater Eng. 2005;48:381–386.
   Web of Science ®Google Scholar
• Thein MA, Lu L, Lai MO. Effect of milling and reinforcement on mechanical properties of nanostructured magnesium composite. J Mater Process Technol. 2009;209:4439–4443.
   Web of Science ®Google Scholar
• Suśniak M, Pałka P, Karwan-Baczewska J. Influence of milling time on the crystallite size of AlSi5Cu2/SiC composite powder. Arch Metall Mater. 2016;61:977–980.
   Web of Science ®Google Scholar
• Viswanath A, Dieringa H, Kumar KA, et al. Investigation on mechanical properties and creep behavior of stir cast AZ91-SiCp composites. J Magnesium Alloys. 2015;3:16–22.
   Web of Science ®Google Scholar
• Suryanarayana C. Mechanical alloying and milling. Prog Mater Sci. 2001;46:1–84.
   Web of Science ®Google Scholar
• Ma J, Lim LC. Effect of particle size distribution on sintering of agglomerate-free submicron alumina powder compacts. J Eur Ceram Soc. 2002;22:2197–2208.
   Web of Science ®Google Scholar
• Fogagnolo JB, Velasco F, Robert MH, et al. Effect of mechanical alloying on the morphology, microstructure and properties of aluminium matrix composite powders. Mater Sci Eng A. 2003;342:131–143.
   Web of Science ®Google Scholar
• Wu Y. Fabrication of metal matrix composite by semi-solid powder processing [dissertation]. Ames (Iowa): State University of Iowa at Ames; 2011.
   Google Scholar
• Keneshloo M, Paidar M, Taheri M. Role of SiC ceramic particles on the physical and mechanical properties of Al–4% Cu metal matrix composite fabricated via mechanical alloying. J Compos Mater. 2017;51:1285–1298.
   Web of Science ®Google Scholar
• Zakeri M, Ramezani M, Nazari A. Effect of ball to powder weight ratio on the mechanochemical synthesis of MoSi2-TiC nanocomposite powder. Mater Res. 2012;15:891–897.
   Web of Science ®Google Scholar
• Luo XT, Li CJ, Yang GJ. Correlations between milling conditions and iron contamination, microstructure and hardness of mechanically alloyed cubic BN particle reinforced NiCrAl matrix composite powders. J Alloys Compd. 2013;548:180–187.
   Web of Science ®Google Scholar