Wear behaviour on a Pin-on-Disc setup for thermal spray of coating using ABAQUS: study and computational analysis

References

• Podra P, Andersson S. Simulating sliding wear with finite element method. Tribol Int. 1999;32:71–81.
   Web of Science ®Google Scholar
• Kim NH, Won D, Burris D, et al. Finite element analysis and experiments of metal/metal wear in oscillatory contacts. Wear. 2005;258(11–12):1787–1793.
   Web of Science ®Google Scholar
• Bosman R, Schipper DJ, “Mild wear maps for boundary lubricated contacts”, Wear 2012, 280–281, 54–62.
   Google Scholar
• Riahi AR, Alpas AT. Wear map for grey cast iron. Wear. 2003;255(1–6):401–409.
   Google Scholar
• Pearson SR, Shipway PH, Abere JO, et al. The effect of temperature on wear and friction of a high strength steel in fretting. Wear. 2013;303(1–2):622–631.
   Web of Science ®Google Scholar
• Friedrich C, Berg G, Broszeit E, et al. PVD Cr N coatings for tribological application on piston rings. Surf Coat Technol. 1997;97(1–3):661–668.
   Web of Science ®Google Scholar
• Broszeit E, Friedrich C, Berg G. Deposition properties and applications of PVD CrN coatings. Surf Coat Technol. 1999;115(1):9–16.
   Web of Science ®Google Scholar
• Costa MYP, Cioffi MOH, Voorwald HJC, et al. An investigation on sliding wear behavior of PVD coatings. Tribol Int. 2010;43(11):2196–2202.
   Web of Science ®Google Scholar
• Navinšek B, Panjan P, Milošev I. Industrial applications of CrN (PVD) coatings, deposited at high and low temperatures. Surf Coat Technol. 1997;97(1–3):182–191.
   Web of Science ®Google Scholar
• Zhang M, Meng G. “Numerical simulation of sliding wear between the rotor bushing and ground plane in micromotors. Sens Actuators a. 2006;126(1):15–24.
   Google Scholar
• Unal H, Mimaroglu A, Kadıoglu U, et al. Sliding Friction and Wear Behaviour of Polytetrafluoroethylene and its Composites under Dry Conditions. Mater Des. 2004;25(3):239–245.
   Web of Science ®Google Scholar
• Cocks M. Interaction of Sliding Metal Surfaces. J Appl Phys. 1962;33(7):2152–2161.
   Web of Science ®Google Scholar
• Yung D.L, Antonov M, Veinthal R . Wear behaviour of doped WC–NI based hard metals tested by four methods, Wear. 2016;352:171–179.
   Web of Science ®Google Scholar
• Onuoha CC, Jin C, Farhat ZN, Kipouros, GJ, Plucknett, KP . The effects of TiC grain size and steel binder content on the reciprocating wear behaviour of TiC-316L stainless steel cermets, Wear. 2016;350:116–129.
   Web of Science ®Google Scholar
• Hovsepiana PE, Mandala P, Ehiasariana AP, Sáfrán, G, Tietema, R, Doerwald, D . Friction and wear behaviour of Mo–W doped carbon-based coating during boundary lubricated sliding, Appl. Surf. Sci. 2016;366:260–274.
   Web of Science ®Google Scholar
• Bolelli G, Milanti A, Lusvarghi L, Trombi, L, Koivuluoto, H, Vuoristo, P, .Wear and impact behaviour of high velocity air-fuel sprayed Fe–Cr–Ni–B–C alloy coatings, Tribol. Int. 2016;95:372–390.
   Web of Science ®Google Scholar
• Culliton D, Betts A, Carvalho S, Kennedy, D . Improving tribological properties of cast Al-Si Alloys through application of wear-resistant thermal spray coatings, J. Therm. Spray Technol. 2013;22(4):491–501.
   Web of Science ®Google Scholar
• Eddazi A, Belattar S. Determination of the defect depth by infrared thermography using finite element method. J Eng Technol. 2017;6(2):215–219.
   Google Scholar
• Hegadekatte V, Huber N, Kraft O. Modeling and simulation of wear in a pin on disc tribometer. Tribology Lett. 2006;24:51–60.
   Web of Science ®Google Scholar
• Mahamani, Mahamani A. Dry sliding wear and friction characteristics of AA6061 - TiB2/zrb2 in-situ metal matrix composites at room temperature. Int J Surf Sci Eng. 2017;11(2):148–173.
   Web of Science ®Google Scholar
• Kanavalli. Application of User Defined Subroutine UMESHMOTION in Abaqus for Simulating Dry Rolling/Sliding Wear [Master Thesis]. Stockholm (Sweden): Royal Institute of Technology (KTH); 2006.
   Google Scholar
• Chowdhury MA, Helali M. The effect of relative humidity and roughness on the friction coefficient under horizontal vibration. Open Mech Eng J. 2008;2:128–135.
   Google Scholar
• Ramteke AM, Ashtankar KM. Finite element analysis study for machining parameters using CNC-RP machining of hip joint part with innovative sacrificial support structure as a fixture. J Eng Technol. 2018;7:337–359.
   Google Scholar