References
- Leu JS, Chu CL, Fuh YK, et al. The combination of rolling-and-T6-treatments with Al2O3-reinforcing-particles effect on A6061 metal-matrix composites. Proc Inst Mech Eng Part L J Mater Des Appl. 2016;230(1):233–239.
- Naik HRM, M LH, Malik V, et al. Effect of microstructure, mechanical and wear on Al-CNTs/graphene hybrid MMC’S. Adv Mater Process Technol. 2021;00:1–14.
- Zafarani HR, Hassani A, Bagherpour E. Achieving a desirable combination of strength and workability in Al/SiC composites by AHP selection method. J Alloys Compd. 2014;589:295–300.
- Maimunnisa S, Gore P, Rajan TPD, et al. Role of centrifugal casting on electrochemical corrosion behavior of A356-SiCp composite in 3.5 wt.% NaCl. J Mater Eng Perform. 2018;27(8):4210–4224.
- Jayakumar E, Praveen AP, Rajan TPD, et al. Studies on tribological characteristics of centrifugally cast SiCp-Reinforced functionally graded A319 aluminium matrix composites. Trans Indian Inst Met. 2018;71(11):2741–2748.
- Iyappan SK, Karthikeyan S, Ravikumar K, et al. Mechanical properties and machinability of aluminium and aluminium-silicon carbide composites processed by Equal Channel Angular Pressing (ECAP). Adv Mater Process Technol. 2020;8(1):1–14.
- Pandey V, Singh JK, Chattopadhyay K, et al. Influence of ultrasonic shotpeening on corrosion behavior of 7075 aluminum alloy. J Alloys Compd. 2017;723:826–840.
- Klotz T, Delbergue D, Bocher P, et al. Surface characteristics and fatigue behavior of shot peened Inconel 718. Int J Fatigue. 2018;110:10–21.
- Liu YG, Li MQ. Structure response characteristics and surface nanocrystallization mechanism of alpha phase in Ti-6al-4V subjected to high energy shotpeening. J Alloys Compd. 2019;773:860–871.
- Sun Q, Liu X, Han Q, et al. A comparison of AA2024 and AA7150 subjected to ultrasonic shotpeening: microstructure, surface segregation and corrosion. Surf Coat Technol. 2018;337:552–560.
- Pandey V, Singh JK, Chattopadhyay K, et al. Optimization of USSP duration for enhanced corrosion resistance of AA7075. Ultrasonics. 2019;91:180–192.
- Dinaharan I, Balakrishnan M, David Raja Selvam J, et al. Microstructural characterization and tensile behavior of friction stir processed AA6061/Al2Cu cast aluminum matrix composites. J Alloys Compd. 2019;781:270–279.
- Kovacı H, Hacısalihoğlu YA, Çelik A. Effects of shotpeening pre-treatment and plasma nitriding parameters on the structural, mechanical and tribological properties of AISI 4140 low-alloy steel. Surf Coat Technol. 2019;358:256–265.
- Wohlfahrt H. The influence of peening conditions on the resulting distribution of residual stress. Proceedings of the Second International Conference on Shot Peening, 1984 May 14, Chicago; 1984. p. 316–331.
- Liu YG, Li MQ, Liu HJ. Nanostructure and surface roughness in the processed surface layer of Ti-6al-4V via shotpeening. Mater Charact. 2017;123:83–90.
- Mozetič M. Surface modification to improve properties of materials. Materials. 2019;12(3):12.
- Nordin E, Alfredsson B. Experimental investigation of shotpeening on case hardened SS2506 gear steel. Exp Tech. 2017;41(4):433–451.
- Ganesh BKC, Ramanaih N, Chandrasekhar Rao PV. Dry sliding wear behavior of Ti–6Al–4V implant alloy subjected to various surface treatments. Trans Indian Inst Met. 2012;65(5):425–434.
- Zammit A, Attard M, Subramaniyan P, et al. Enhancing surface integrity of titanium alloy through hybrid surface modification (HSM) treatments. Mater Chem Phys. 2022;279:125768.
- Mordyuk BN, Prokopenko GI, Vasylyev MA, et al. Effect of structure evolution induced by ultrasonic peening on the corrosion behavior of AISI-321 stainless steel. Mater Sci Eng A. 2007;458(1–2):253–261.
- Xie L, Jiang C, Lu W, et al. Investigation on the residual stress and microstructure of (TiB+tic)/Ti–6Al–4V composite after shot peening. Mater Sci Eng A. 2011;528(9):3423–3427.
- Kovacı H, Bozkurt YB, Yetim AF, et al. The effect of surface plastic deformation produced by shotpeening on corrosion behavior of a low-alloy steel. Surf Coat Technol. 2019;360:78–86.
- Agarwal KM, Tyagi RK, Saxena KK. Deformation analysis of Al alloy AA2024 through equal channel angular pressing for aircraft structures. Adv Mater Process Technol. 2020;8(1):1–15.
- Kulekci MK, Esme U. Critical analysis of processes and apparatus for industrial surface peening technologies. Int J Adv Manuf Technol. 2014;74(9–12):1551–1565.
- Turalıoğlu K, Taftalı M, Tekdir H, et al. The tribological and corrosion properties of anodized Ti6Al4V/316L bimetallic structures manufactured by additive manufacturing. Surf Coat Technol. 2021;405:126635.
- Alam MT, Ansari AH. X-Ray diffraction analysis and microstructural examination of Al-Sic composite fabricated by stir casting technique. Int J Sci Technol Manag. 2015;4:941–955.
- Webster GA, Ezeilo AN. Residual stress distributions and their influence on fatigue lifetimes. Int J Fatigue. 2001;23:375–383.
- Bagheri S, Guagliano M. Review of shotpeening processes to obtain nanocrystalline surfaces in metal alloys. Surf Eng. 2009;25(1):3–14.
- Lu S, Hu QM, Delczeg-Czirjak EK, et al. Determining the minimum grain size in severe plastic deformation process via first-principles calculations. Acta Mater. 2012;60(11):4506–4513.
- Bagherifard S, Pariente IF, Guagliano M, et al. Fatigue analysis of shot peened smooth and notched steel specimens. 11th International Conference of Shot Peening, South Bend; 2011 93–97.
- Yi S, Wollmann M, Ludian T, et al. Analyzing the near-surface deformation gradients due to shotpeening and ball-burnishing of alpha brass and stainless steel. International Conference on Shot Peening, year 2008, Tokyo, Japan; Vol. 10. 2008. p. 169.