Possibility of infrared (IR) thermography camera to investigate properties of injected plastic product and optimisation injection process parameter using a design of experiment

References

• Ozcelik B, Kuram E, Topal MM. Investigation the effects of obstacle geometries and injection molding parameters on weld line strength using experimental and finite element methods in plastic injection molding. Int Commun Heat Mass Transf. 2012;39(2):275–281.
   Web of Science ®Google Scholar
• Shi H, Xie S, Wang X. A warpage optimization method for injection molding using artificial neural network with parametric sampling evaluation strategy. Int J Adv Manuf Technol. 2013;65(1–4):343–353.
   Web of Science ®Google Scholar
• Zhou X, Zhang Y, Mao T, et al. Monitoring and dynamic control of quality stability for injection molding process. J Mater Process Technol. 2017;249:358–366.
   Web of Science ®Google Scholar
• Bula K, Różański L, Marciniak-Podsadna L, et al. The use of IR thermography to show the mold and part temperature evolution in injection molding. Arch Mech Technol Mat. 2016;36(1):40–43.
   Google Scholar
• Yu S, Zhang T, Zhang Y, et al. Intelligent setting of process parameters for injection molding based on case-based reasoning of molding features. J Intell Manuf. 2022;33(1):77–89. DOI:10.1007/s10845-020-01658-y
   Web of Science ®Google Scholar
• Bendada A, Derdouri A, Simard Y, et al. Advances in infrared technology for the online monitoring of injection moulding: application to the understanding of the nature of contact at the polymer—mould interface. Trans Inst Meas Control. 2007;29(5):431–451.
   Web of Science ®Google Scholar
• Suriani MJ, Ali A, Khalina A, et al. Haftirman. Detection of defects in natural composite materials using thermal imaging technique. Mater Test. 2012;54(5):340–346. DOI:10.3139/120.110333.
   Web of Science ®Google Scholar
• Bagavathiappan S, Lahiri BB, Saravanan T, et al. Infrared thermography for condition monitoring – a review. Infrared Phys Technol. 2013;60:35–55.
   Web of Science ®Google Scholar
• Omar M, Hassan M, Donohue K, et al. Infrared thermography for inspecting the adhesion integrity of plastic welded joints. NDT E Int. 2006;39(1):1–7.
   Web of Science ®Google Scholar
• Ageyeva T, Horváth S, Kovács JG. In-mold sensors for injection molding: on the way to industry 4.0. Sens (Basel). 2019;19(16):3551.
   PubMed Web of Science ®Google Scholar
• Schwalme G. Inline infrared thermography applied for quality gates and for mould temperature control in the injection moulding process. Engineering. 58th Ilmenau Scientific Colloquium, Technische Universität Ilmenau, 8–12 September 2014.
   Google Scholar
• Suriani MJ, Ali A, Khalina A, et al. Detection of defects in kenaf/epoxy using infrared thermal imaging technique. Procedia Chem. 2012;4:172–178.
   Google Scholar
• Li Y, Chen JC, Ali WM. Process optimization and in-mold sensing enabled dimensional prediction for high precision injection molding. Int J Interact Des Manuf. 2022;16(3):997–1013.
   Google Scholar
• Kajita S, Aumeunier M-H, Yatsuka E, et al. Effect of wall light reflection in ITER diagnostics. Nucl Fusion. 2017;57(11):116061. DOI:10.1088/1741-4326/aa7ef7
   Web of Science ®Google Scholar
• Aumeunier M-H, Gerardin J, Talatizi C, et al. Infrared thermography in metallic environments of WEST and ASDEX upgrade. Nucl Mater Energy. 2021;26:100879.
   Web of Science ®Google Scholar
• Mohan M, Ansari MNM, Shanks RA. Review on the effects of process parameters on strength, shrinkage, and warpage of injection molding plastic component. Polym Plast Technol and Eng. 2017;56(1):1–12.
   Web of Science ®Google Scholar
• Moayyedian M, Abhary K, Marian R. The analysis of short shot possibility in injection molding process. Int J Adv Manuf Technol. 2017;91(9–12):3977–3989.
   Web of Science ®Google Scholar
• Barghash MA, Alkaabneh FA. Shrinkage and warpage detailed analysis and optimization for the injection molding process using multistage experimental design. Qual Eng. 2014;26(3):319–334.
   Web of Science ®Google Scholar
• Moayyedian M, Abhary K, Marian R. Optimization of injection molding process based on fuzzy quality evaluation and Taguchi experimental design. CIRP J Manuf Sci Technol. 2018;21:150–160.
   Web of Science ®Google Scholar
• Malloy RA. Manufacturing considerations for injection molded parts. Plastic part design for injection molding. 2nd ed. München: Carl Hanser Verlag GmbH & Co. KG; 2010. DOI:10.3139/9783446433748.002.
   Google Scholar
• Karagöz İ. An effect of mold surface temperature on final product properties in the injection molding of high-density polyethylene materials. Polym Bull. 2021;78(5):2627–2644.
   Web of Science ®Google Scholar
• Fukushima Y, Kosaka M, Sakamoto A. A study on the optimal mould design method for the prevention of weld-line by injection moulding CAE. Adv Mater Process Technol. 2022;8(2):1534–1549.
   Google Scholar
• Ahamed DAR, Dawood DAKS, Karthikeyan R. Designing and optimizing the parameters which affect the molding process using design of experiment. Int J Res Mech Eng. 2013;1:116–122.
   Google Scholar
• Singh G, Pradhan MK, Verma A. Effect of injection moulding process parameter on tensile strength using taguchi method. Int Scholarly Sci Res Innovation. 2015;9:1844–1849.
   Google Scholar
• Rizvi SJA, Singh AK, Bhadu GR. Optimization of tensile properties of injection molded α-nucleated polypropylene using response surface methodology. Polym Test. 2017;60:198–210.
   Web of Science ®Google Scholar
• Rizvi SJA. Effect of injection molding parameters on crystallinity and mechanical properties of isotactic polypropylene. Int J Plast Technol. 2017;21(2):404–426.
   Google Scholar