Fabrication of coloured zirconia ceramics by infiltrating water debound injection moulded green body

References

• German RM: ‘Powder injection molding’; 1990, Princeton, NJ, MPIF.
   Google Scholar
• Song JH, Evans JRG: ‘The injection‐molding of fine and ultra‐fine zirconia powders’, Ceram. Int., 1995, 21, (5), 325–333.
   Web of Science ®Google Scholar
• Song JH, Edirisinghe MJ, Evans JRG, Twizell EH: ‘Modeling the effect of gas transport on the formation of defects during thermolysis of powder moldings’, J. Mater. Res., 1996, 11, (4), 830–840.
   Web of Science ®Google Scholar
• Huzzard RJ, Blackburn S: ‘Influence of solids loading on aqueous injection moulding paste’, Br. Ceram. Trans., 1999, 98, (2), 49–56.
   Google Scholar
• Soykan HS, Karakas Y: ‘Injection moulding of thin walled zirconia tubes for oxygen sensors’, Adv. Appl. Ceram., 2005, 104, (6), 285–290.
   Web of Science ®Google Scholar
• Shaw HM, Edirisinghe MJ: ‘Porosity development during removal of organic vehicle from ceramic injection moldings’, J. Eur. Ceram. Soc., 1994, 13, (2), 135–142.
   Web of Science ®Google Scholar
• Shaw HM, Edirisinghe MJ: ‘Shrinkage and particle packing during removal of organic vehicle from ceramic injection moldings’, J. Eur. Ceram. Soc., 1995, 15, (2), 109–116.
   Web of Science ®Google Scholar
• Bakan HI: ‘Injection moulding of alumina with partially water soluble binder system and solvent debinding kinetics’, Mater. Sci. Technol., 2007, 23, (7), 787–791.
   Web of Science ®Google Scholar
• Yang WW, Yang KY, Wang MC, Hon MH: ‘Solvent debinding mechanism for alumina injection molded compacts with water‐soluble binders’, Ceram. Int., 2003, 29, (7), 745–756.
   Web of Science ®Google Scholar
• Krauss VA, Oliveira AAM, Klein AN, Al‐Qureshi HA, Fredel MC: ‘A model for PEG removal from alumina injection moulded parts by solvent debinding’, J. Mater. Process. Technol., 2007, 182, (1–3), 268–273.
   Web of Science ®Google Scholar
• Hu SC, Hwang KS: ‘Length change and deformation of powder injection‐molded compacts during solvent debinding’, Metall. Mater. Trans. A, 2000, 31A, (5), 1473–1478
   Web of Science ®Google Scholar
• Liu DM, Tseng WJ: ‘Influence of debinding rate, solid loading and binder formulation on the green microstructure and sintering behaviour of ceramic injection mouldings’, Ceram. Int., 1998, 24, (6), 471–481
   Web of Science ®Google Scholar
• Shivashankar TS, German RM: ‘Effective length scale for predicting solvent‐debinding times of components produced by powder injection molding’, J. Am. Ceram. Soc., 1999, 82, (5), 1146–1152
   Web of Science ®Google Scholar
• Song JH, Evans JRG, Edirisinghe MJ, Twizell EH: ‘Effect of powder bed on critical heating rates for thermolysis of ceramic injection moldings’, AIChE J., 1996, 42, (6), 1715–1722
   Web of Science ®Google Scholar
• Aboushelib MN, Kleverlaan CJ, Feilzer AJ: ‘Effect of zirconia type on its bond strength with different veneer ceramics’, J. Prosthodont., 2008, 17, (5), 401–408
   Google Scholar
• Pittayachawan P, McDonald A, Petrie A, Knowles JC: ‘The biaxial flexural strength and fatigue property of Lava (TM) Y‐TZP dental ceramic’, Dent. Mater., 2007, 23, (8), 1018–1029
   Web of Science ®Google Scholar
• Schabbach LM, Bondioli F, Ferrari AM, Manfredini T, Petter CO, Fredel MC: ‘Color in ceramic glazes: analysis of pigment and opacifier grain size distribution effect by spectrophotometer’, J. Eur. Ceram. Soc., 2008, 28, (9), 1777–1781
   Web of Science ®Google Scholar
• Chiou YH, Lin ST: ‘Influence of CoO and Al2O3 on the phase partitioning of ZrO2‐3 mol% Y2O3’, Ceram. Int., 1996, 22, (3), 249–256.
   Web of Science ®Google Scholar
• Fujisaki H: ‘Zirconia‐containing powder for black zirconia sintered body, e.g. for ornamental articles such as watch bands, contains specified amount of cobalt–zinc–iron–aluminum or aluminum oxide containing pigment, aluminum oxide, and yttrium oxide’, European patent no. EP1857428A1, 21 November 2007.
   Google Scholar
• Marple BR, Green DJ: ‘Mullite alumina particulate composites by infiltration processing’, J. Am. Ceram. Soc., 1989, 72, (11), 2043–2048
   Web of Science ®Google Scholar
• Albano MP, Scian AN: ‘Mullite/SiAlON/alumina composites by infiltration processing’, J. Am. Ceram. Soc., 1997, 80, (1), 117–124.
   Web of Science ®Google Scholar
• Glass SJ, Green DJ: ‘Permeability and infiltration of partially sintered ceramics’, J. Am. Ceram. Soc., 1999, 82, (10), 2745–2752.
   Web of Science ®Google Scholar
• Marple BR, Green DJ: ‘Graded compositions and microstructures by infiltration processing’, J. Mater. Sci., 1993, 28, (17), 4637–4643.
   Web of Science ®Google Scholar
• Washburn EW: ‘The dynamics of capillary flow’, 1921, , 374–375 College Park, MD, American Physical Society.
   Google Scholar
• Einset EO: ‘Capillary infiltration rates into porous media with applications to Silcomp processing’, J. Am. Ceram. Soc., 1996, 79, (2), 333–338
   Web of Science ®Google Scholar
• ‘Colorimetry’; 1986, Vienna, Central Bureau of the Commission Internationale de l'Eclairage.
   Google Scholar