References
- Banks RB and Chandrasekhara DV: ‘Experimental investigation of the penetration of a high velocity gas jet through a liquid surface’, J. Fluid Mech., 1963, 15, (1), 13–34.
- Banks RB and Bhavamai A: ‘Experimental study of the impingement of a liquid jet on the surface of a heavier liquid’, J. Fluid Mech., 1965, 23, 229–240.
- Cheslak FR, Nicholls JA and Sichel M: ‘Cavities formed on liquid surfaces by impinging gaseous jets’, J. Fluid Mech., 1969, 36, 55–63.
- Qian F, Mutharasan R and Farouk B: ‘Studies of interface deformations in single- and multi-layered liquid baths due to an impinging gas jet’, Metall. Trans., 1996, 27B, 911–920.
- Lee M, Whitney V and Molloy N: ‘Jet-liquid interaction in a steelmaking electric arc furnace,’ Scand. J. Metall., 2001, 30, 330–336.
- Alam MA, Irons G, Brooks G, Fontana A and Naser J: ‘Inclined jetting and splashing in electric arc furnace steelmaking’, ISIJ Int., 2011, 51, 1439–1447.
- Hwang H and Irons GA: ‘A water model study of impinging gas jets on liquid surfaces’, Metall. Trans., 2012, 43B, 302–315.
- Ek M and Sichen D: ‘Study of penetration depth and droplet behavior in the case of a gas jet impinging on the surface of molten metal using liquid Ga–In–Sn’, Steel Res. Int., 2012, 83, 678–685.
- Alam M, Naser J, Brooks G and Fontana A: ‘A computational fluid dynamics model of shrouded supersonic jet impingement on a water surface’, ISIJ Int., 2012, 52, 1026–1035.
- Ersson M, Tilliander A, Jonsson L and Jönsson P: ‘A mathematical model of an impinging air jet on a water surface’, ISIJ Int., 2008, 48, 377–384.
- Ersson M, Höglund L, Tilliander A, Jonsson L and Jönsson P: ‘Dynamic coupling of computational fluid dynamics and thermodynamics software: applied on a top blown converter’, ISIJ Int., 2008, 48, 147–153.
- Huda N, Naser J, Brooks G, Reuter M and Matusewicz R: ‘CFD modeling of swirl and nonswirl gas injections into liquid baths using top submerged lances,’ Metall. Trans., 2010, 41B, 35–50.
- Hwang HY and Irons GA: ‘Mathematical modeling of impinging gas jets on liquid surfaces’, Metall. Trans., 2011, 42B, 575–591.
- Alam M, Brooks G and Naser J: ‘Modelling of supersonic oxygen jet injection inside steelmaking furnace’, Paper presented at the 4th Australia-China-Japan Joint symposium of Iron and Steelmaking, Shenyang, China, 2012.
- Alam M, Naser J and Brooks G: ‘Computational fluid dynamics simulation of supersonic oxygen jet behavior at steelmaking temperature’, Metall. Trans., 2010, 41, (3), 636–645.
- Asahara N, Naito K, Kitagawa I, Matsuo M, Kumakura M and Iwasaki M: ‘Fundamental study on interaction between top blown jet and liquid bath’, Steel Res. Int., 2011, 82, (5), 587–594.
- Sumi I, Kishimoto Y, Kikichi Y and Igarashi H: ‘Effect of high-temperature field on supersonic oxygen jet behavior’, ISIJ Int., 2006, 46, (9), 1312–1317.
- Hirt CW and Nichols BD: ‘Volume of Fluid (VOF) method for the dynamics of free boundaries’, J. Comp. Phys., 1981, 39, 201–225.
- Berberovic E, Van Hinsberg NP, Jakirlic S, Roisman IV and Tropea C: ‘Drop impact onto a liquid layer of finite thickness: dynamics of the cavity evolution’, Phys. Rev. E, 2009, 79, 036306.
- Brackbill JU, Kothe DB and Zemach C: ‘A continuum method for modeling surface tension’, J. Comp. Phys., 1992, 100, 335–354.
- Ubbink O and Isssa RI: ‘A method for capturing sharp fluid interfaces on arbitrary meshes’, J. Comp. Phys., 1999, 153, 26–50.
- Hinze JO: ‘Turbulence, an introduction to its mechanism and theory’, 404; 1959, New York, USA, McGraw-Hill Book Company Inc.
- Li DS, Ren H and Xie CS: ‘A fluid-dynamical lower density simulation test for LD converter’, Acta Metall. Sin., 1979, 15, (1), 12–22.
- Chatterjee A and Bradshaw AV: ‘Break-up of a liquid surface by an impinging gas jet’, J. Iron Steel Inst., 1972, 210, (3), 179–187.
- Laufer J: ‘Turbulent shear flows of variable density’, AIAA Journal, 1969, 7, (4), 706–713.
- Folsomr G and Fergusoc NK: Trans. Am. Soc. Mech. Eng., 1949, 71, 73.
- Meidani ARN, Isac M, Richardson A, Cameron A and Guthrie RIL: ‘Modelling shrouded supersonic jets in metallurgical reactor vessels’, ISIJ Int., 2004, 44, (10), 1639–1645.
- Oxygen Lance Research Group: ‘Experimental measuring on oxygen lance of a 150t top blown steelmaking converter based cold model’, Iron Steel, 1977, 4, 25–44.
- Wang W, Yuan Z, Matsuura H, Zhao H, Dai C and Tsukihashi F: ‘Three-dimensional compressible flow simulation of top-blown multiple jets in convertor’, ISIJ Int., 2010, 50, 491–500.
- Memoli F, Mapelli C, Ravanelli P and Corbella M: ‘Simulation of oxygen penetration and decarburization in EAF using supersonic injection system’, ISIJ Int., 2004, 44, 1342–1349.
- Koria SC: ‘Studies of the bath mixing intensity in converter steelmaking processes’, Can. Metall. Q., 1992, 8, 105–112.
- Kumagai T and Iguchi M: ‘Instability phenomena at bath surface induces by top lance gas injection’, ISIJ Int., 2001, 41, S52–S55.
- Molloy NA: ‘Impinging jet flow in a two phase system: the basic flow pattern’, J. Iron Steel Inst., 1970, 56, 943–950.