5
Views
4
CrossRef citations to date
0
Altmetric
Technical Paper

Elaborated Constitutive Equations for Structural Analysis for Creep, Swelling, and Damage Under Irradiation

&
Pages 219-227 | Published online: 12 May 2017

REFERENCES

  • J. GITTUS, Irradiation Effects in Crystalline Solids, Applied Science Publishers, London (1978).
  • K. EHRLICH, “Irradiation Creep and Interrelation with Swelling in Austenitic Stainless Steels,” J. Nucl. Mater., 100, 149 (1981).
  • J. R. MATTHEWS and M. W. FINNIS, “Irradiation Creep Models–An Overview,” J. Nucl. Mater., 159, 257 (1988).
  • F. A. GARNER and D. S. GELLES, “Irradiation Creep Mechanisms: An Experimental Perspective,” J. Nucl. Mater., 159, 286 (1988).
  • E. R. GILBERT and B. A. CHIN, “In-Reactor Creep Measurements,” Nucl. Technol., 52, 273 (1981).
  • D. L. PORTER, M. L. TAKATA, and E. L. WOOD, “Direct Evidence for Stress-Enhanced Swelling in Type 316 Stainless Steel,” J. Nucl. Mater., 116, 272 (1983).
  • J. H. GITTUS, “Theory of Dislocation-Creep Due to the Frenkel Defects or Interstitialcies Produced by Bombardment with Energetic Particles,” Phil. Mag., 25, 345 (1972).
  • L. K. MANSUR and T. C. REILEY, “Irradiation Creep by Dislocation Glide Enabled by Preferred Absorption of Point Defects—Theory and Experiment,” J. Nucl. Mater., 90, 60 (1980).
  • P. T. HEALD and M. V. SPEIGHT, “Point Defect Behavior in Irradiated Materials,” Acta Metallurgica, 23, 1389 (1975).
  • P. T. HEALD and J. E. HARBOTTLE, “Irradiation Creep Due to Dislocation Climb and Glide,” J. Nucl. Mater., 67, 229 (1977).
  • R. A. WEINER and A. BOLTAX, “Microstructural Modeling of Irradiation Creep and Swelling,” J. Nucl. Mater., 66, 1 (1977).
  • W. G. WOLFER, “Correlation of Radiation Creep Theory with Experimental Evidence,” J. Nucl. Mater., 90, 175 (1980).
  • A. D. BRAILSFORD and R. BULLOUGH, “Irradiation Creep Due to the Growth of Interstitial Loops,” Phil. Mag., 27, 49 (1973).
  • S. MURAKAMI, M. MIZUNO, and T. OKAMOTO, “Mechanical Modeling of Creep, Swelling and Damage Under Irradiation for Polycrystalline Metals,” Nucl. Eng. Design (in press).
  • J. F. BATES and M. K. KORENKO, “Empirical Development of Irradiation-Induced Swelling Design Equations,” Nucl. Technol., 48, 303 (1980).
  • P. G. McVETTY, “Working Stress for High Temperature Service,” Mech. Eng., 56, 149 (1934).
  • L. M. KACHANOV, Introduction to Continuum Damage Mechanics, Martinus Nijhoff, Dordrecht (1986).
  • E. A. LECKIE and D. R. HAYHURST, “Constitutive Equations for Creep Rupture,” Acta Metallurgica, 25, 1059 (1977).
  • D. C. LEIGH, Nonlinear Continuum Mechanics, McGraw-Hill, New York (1968).
  • W. JAUNZEMIS, Continuum Mechanics, Macmillan, New York (1967).
  • T. A. KENFIELD, W. K. APPLEBY, H. J. BUSBOOM, and W. L. BELL, “Swelling of Type-316 Stainless Steel at High Fluences in EBR-II,” J. Nucl. Mater., 75, 85 (1978).
  • A. BOLTAX, J. P. FOSTER, R. A. WEINER, and A. BIANCHERIA, “Void Swelling and Irradiation Creep Relationships,” J. Nucl. Mater., 65, 174 (1977).
  • J. P. FOSTER and R. V. STRAIN, “Empirical Swelling Equations for Solution-Annealed Type 304 Stainless Steel,” Nucl. Technol., 24, 93 (1974).
  • S. MURAKAMI, Y. SANOMURA, and K. SAITOH, “Formulation of Cross-Hardening in Creep and Its Effect on the Creep Damage Process of Copper,” ASME J. Eng. Mater. Technol., 108, 167 (1986).
  • S. MURAKAMI and N. OHNO, “A Constitutive Equation of Creep Based on the Concept of a Creep-Hardening Surface,” Int. J. Solids Struct., 18, 597 (1982).
  • J. L. CHABOCHE, “Constitutive Equations for Cyclic Plasticity and Cyclic Viscoplasticity,” Int. J. Plasticity, 5, 247 (1989).
  • E. R. GILBERT, B. A. CHIN, and D. R. DUNCAN, “Effect of Irradiation on Failure Mode During Creep,” Metallurgical Trans. A, 18A, 79 (1987).
  • E. E. BLOOM and J. R. WEIR, “Effect of Neutron Irradiation on the Ductility of Austenitic Stainless Steel,” Nucl. Technol., 16, 45 (1972).
  • S. MURAKAMI, M. MIZUNO, and H. OGAWA, “Finite Element Analysis of Creep-Crack Growth Under Neutron Irradiation,” Proc. Conf. Materials and Mechanics, Toyohashi City, Japan, November 28–29, No. 900-86, p. 466, Japan Society of Mechanical Engineers (1990).

Reprints and Corporate Permissions

Please note: Selecting permissions does not provide access to the full text of the article, please see our help page How do I view content?

To request a reprint or corporate permissions for this article, please click on the relevant link below:

Academic Permissions

Please note: Selecting permissions does not provide access to the full text of the article, please see our help page How do I view content?

Obtain permissions instantly via Rightslink by clicking on the button below:

If you are unable to obtain permissions via Rightslink, please complete and submit this Permissions form. For more information, please visit our Permissions help page.