References
- Asian, E., Camuscu, N. & Birgoren, B. 2007, “Design of optimization of cutting parameters when turning hardened AISI 4140 steel (63 HRC) with Al2O3+TiCN mixed ceramic tool”, Materials and Design, Vol. 28, pp. 1618–1622.
- Choudhury, I. A. & El-Baradie, M. A. 1998, “Machinability of nickel-base super alloys: a general view”, Journal Materials Processing Technology, Vol. 77, pp.278–284.
- Davim, J. P. 2001, “A note on the determination of optimal cutting conditions for surface finish obtained in turning using design of experiments”, Journal Materials Processing Technology, Vol. 116, pp.305–308.
- Davim, J. P. 2003, “Design of optimisation of cutting parameters for turning metal matrix composites based on the orthogonal arrays”, Journal Materials Processing Technology, Vol. 132, pp.340–344.
- Davis, M. A, Chou, Y. & Evans, C. J. 1996, Ann.CIRP 45, pp. 77–82.
- Deng, J., Liu, L., Liu, J., Zhao, J. & Yang, X. 2005, “Failure mechanisms of TiB2 particle and SiC whisker reinforced Al2O3 ceramic cutting tools when machining nickel-based alloys”, Int. J. Mach. Tools Manufact., Vol. 45, No. 12-13, pp. 1393–1401.
- Erginc, B., Kampu, Z. & Sustarsic, B. 2006, “The use of the Taguchi approach to determine the influence of injection – molding parameters on the properties of green parts”, Journal of Achievement in Materials and Manufacturing Engineering, Vol. 15.
- Ezugwu, E. O. 2005, “Key improvements in the machining of difficult-to-cut aerospace super alloys”, International Journal of Machine Tools and Manufacture, Vol. 45, No. 12-13, pp. 1353–1367.
- Ghani, J. A., Choudhury, I. A. & Hassan, H. H. 2004, “Application of Taguchi method in the optimization of end milling parameters”, Journal of Materials Processing Technology, Vol. 145, pp. 84–92.
- Hascalik, A. & Caydas, U. 2007, “Optimization of turning parameters for surface roughness and tool life based on the Taguchi method”, International Journal of Advanced Manufacturing Technology, pp. 1147–1154.
- Jawaid, A., Koksal, S. & Sharif, S. 2000, “Wear behavior of PVD and CVD coated carbide tools when face milling Inconel 718”, Tribol. Trans., Vol. 43, No. 2, pp. 325–331.
- Königi, W., Klinger, M. & Link, R. 1990, Ann.CIRP 39, pp. 61–64.
- Liao, Y. S. & Shiue, R. H. 1996, “Carbide tool wear mechanism in turning of Inconel 718 with ceramic tools”, Wear, Vol. 193, pp. 16–24.
- Molinari, A. & Nouari, M. 2002, “Modeling of tool wear by diffusion in metal cutting”, Wear, Vol. 525, pp. 135–149.
- PuertasArbizu, I. & LuisPerez, C. J. 2003, “Surface roughness prediction by factorial design of experiments in turning processes”, Journal Materials Processing Technology, Vol. 143-144, pp.390–396.
- Rahman, M., Seah, W. K. H. & Teo, T. T. 1997, “The machinability of Inconel 718”, Journal Materials Processing Technology, Vol. 63, pp. 199–204.
- Rosa, J. L., Robin, A., Silva, M. B., Baldan, C. A. & Peres, M. P. 2009, “Electrodeposition of copper on titanium wires: Taguchi experimental design approach”, J. Mater. Process Technol., Vol. 209, pp. 1181–1188.
- Ross, P. J. 1989, Taguchi techniques for quality engineering, McGraw-Hill, New York.
- Ross, P. J. 1996, Taguchi techniques for quality engineering: loss function, orthogonal experiments, parameter and tolerance design, 2nd edition, McGraw-Hill, New York.
- Roy, R. K. 1990, A primer on Taguchi method, Von Nostrad Reinhold, NY.
- Senthilkumaar, J. S., Selvarani, P. & Arunachalam, R. M. 2010, “Selection of machining parameters based on the analysis of surface roughness and flank wear in finish turning and facing of Inconel 718 using Taguchi’s technique”, Emirates Journal for Engineering Research, Vol. 15/2, pp. 41–49.
- Shaw, M. C. 1984, Metal Cutting Principles, Clarendon Press, Oxford.
- Thomas, M., Beauchamp, Y., Youssef, Y. A. & Masounave, J. 1997, “An experimental design for surface roughness and built-up edge formation in lathe dry turning”, International Journal of Quality Science, Vol. 2/3, pp. 167–180.
- Yang, W. H. & Tang, Y. S. 1998, “Design optimization of cutting parameters for turning operations based on Taguchi method”, Journal of Materials Processing Technology, Vol. 84, pp. 122–129.