References
- Sekhar AP, Mandal AB, Das D. Mechanical properties and corrosion behavior of artificially aged Al-Mg-Si alloy. J Mater Res Technol. 2020;9:1005–1024. doi:https://doi.org/10.1016/j.jmrt.2019.11.040.
- Cai M, Field D, Lorimer G. A systematic comparison of static and dynamic ageing of two Al–Mg–Si alloys. Mater Sci Eng A. 2004;373:65–71. doi:https://doi.org/10.1016/j.msea.2003.12.035.
- Mrówka-Nowotnik G, Sieniawski J. Influence of heat treatment on the microstructure and mechanical properties of 6005 and 6082 aluminium alloys. J Mater Process Technol. 2005;162–163:367–372. doi:https://doi.org/10.1016/j.jmatprotec.2005.02.115.
- Taban E, Gould JE, Lippold JC. Characterization of 6061-T6 aluminum alloy to AISI 1018 steel interfaces during joining and thermo-mechanical conditioning. Mater Sci Eng. A. 2010;527:1704–1708. doi:https://doi.org/10.1016/j.msea.2009.10.059.
- Xu C, He H, Yu W, et al. Influence of quenching temperature on peak aging time and hardness of Al-Mg-Si-Cu alloys strengthened by nano-sized precipitates. Mater Sci Eng A. 2019;744:28–35. doi:https://doi.org/10.1016/j.msea.2018.11.149.
- Xu X, Deng Y, Chi S, et al. Effect of interrupted ageing treatment on the mechanical properties and intergranular corrosion behavior of Al-Mg-Si alloys. J Mater Res Technol. 2020;9:230–241. doi:https://doi.org/10.1016/j.jmrt.2019.10.050.
- ASM Handbook. Heat treating of aluminum alloys. Vol. 4. ASM International; 1991. p. 1862–1960.
- Maisonnette D, Suery M, Nelias D, et al. Effects of heat treatments on the microstructure and mechanical properties of a 6061 aluminium alloy. Mater Sci Eng A. 2011;528:2718–2724. doi:https://doi.org/10.1016/j.msea.2010.12.011.
- Siddiqui RA, Abdullah HA, Al-belushi KR. Influence of aging parameters on the mechanical properties of 6063 aluminium alloy. Mater Process Technol. 2000;102:234–240.
- ASTM International. Standard specification for aluminum and aluminum-alloy extruded bars, rods, wire, profiles and tubes, B 221M. 2002; p. 1–14.
- ASTM International. Standard specification for aluminum and aluminum-alloy seamless pipe and seamless extruded tube, B 241/B 241M. 2002; p. 16. https://doi.org/https://doi.org/10.1520/B0241.
- ASM Handbook. Metallography and microstructures. Ohio: ASM International. 2004. doi:https://doi.org/10.31399/asm.hb.v09.9781627081771.
- ASTM International. Standard test method for indentation hardness of aluminum alloys by means of a Webster Hardness Gage, B647. 2010; p. 4.
- Montgomery DC. Diseño y análisis de experimentos. 2004.
- Carreño Morelli E, Ghilarducci AA, Urreta de Pereyra SE. Relation between fabrication parameters and grain boundary internal friction peaks in commercial Al-Mg-Si alloys. J Alloys Compd. 1994;211–212:484–488. doi:https://doi.org/10.1016/0925-8388(94)90549-5.
- ASM Handbook. Nonferrous alloys and special-purpose materials. Vol. 2. Ohio: ASM International. 1990; p. 40–60.
- Asensio Lozano J, Suárez Peña B. Análisis cuantitativo y caracterización morfológica de la aleación 6063. Diferencias microestructurales y mecánicas entre la superficie y el núcleo de barras cilíndricas de colada semicontinua. Rev Metal. 2012;48:199–212. doi:https://doi.org/10.3989/revmetalm.1135.
- ASM Handbook. Heat treating of aluminum alloys. Ohio. 1991. doi:https://doi.org/10.1361/asmhba000.
- Grong O. Metallurgical modelling of welding. 1997.
- Mrówka-Nowotnik G. Influence of chemical composition variation and heat treatment on microstructure and mechanical properties of 6xxx alloys. Arch Mater Sci Eng. 2010;46:6–13.
- Gaber A, Afify N. Characterization of the precipitates in Al-Li(8090) alloy using thermal measurements and TEM examinations. Phys B. 2002;315:1–6. doi:https://doi.org/10.1016/S0921-4526(01)01470-3.
- Esmaeili S, Lloyd DJ, Poole WJ. Modeling of precipitation hardening for the naturally aged Al-Mg-Si-Cu alloy AA6111. Acta Mater. 2003;51:3467–3481. doi:https://doi.org/10.1016/S1359-6454(03)00167-8.
- Edwards GA, Stiller K, Dunlop GL, et al. The precipitation sequence in Al–Mg–Si alloys. Acta Mater. 1998;46:3893–3904. doi:https://doi.org/10.1016/S1359-6454(98)00059-7.
- ASTM International. Standard test methods for determining average grain size, E-112. 2004; p. 1–26. http://image.sciencenet.cn/olddata/kexue.com.cn/bbs/upload/9943ASTM_standard__E_112_standard_test_methods_for_determining_average_grain_size.pdf.