References
- S. Polak et al., Warm forming of 7075 aluminum alloys, Proc. Eng. 207, 2399 (2017). DOI: 10.1016/j.proeng.2017.10.1015.
- Y. Wang et al., Rigid-flexible coupling forming process for aluminum alloy automobile body panels, Int. J. Adv. Manuf. Tech. 770, 324 (2014). DOI: 10.1007/s00170-017-1494-4.
- S. P. Keeler, and W. A. Backofen, Plastic instability and fracture in sheets stretched over rigid punches, ASM Trans. Q. 56, 25 (1963).
- S. Ahmadi, A. R. Eivani, and A. Akbarzadeh, An experimental and theoretical study on the prediction of forming limit diagrams using new BBC yield criteria and M-K analysis, Comp. Mater. Sci. 44 (4), 1272 (2009). DOI: 10.1016/j.commatsci.2008.08.013.
- S. Panich et al., Experimental and theoretical formability analysis using strain and stress based forming limit diagram for advanced high strength steels, Mater. Design 51 (5), 756 (2013). DOI: 10.1016/j.matdes.2013.04.080.
- X. C. Zhuang, C. Xu, and Z. Zhao, Experimental and numerical investigation of failure mode in geometrically imperfect DP590 steel, Sci. China Technol. Sci. 58 (3), 476 (2015). DOI: 10.1007/s11431-015-5772-9.
- H. Wang, Acquisition method of forming limit diagram and its application in sheet metal forming, Ph.D. dissertation, Nanjing University of Aeronautics and Astronautics, 2011.
- M. Dilmec et al., Effects of sheet thickness and anisotropy on forming limit curves of AA2024-T4, Int. J. Adv. Manuf. Technol. 67 (9–12), 2689 (2013). DOI: 10.1007/s00170-012-4684-0.
- G. Fang et al., Comparative analysis between stress- and strain-based forming limit diagrams for aluminum alloy sheet 1060, T. Nonferr. Metal Soc. 22, 343 (2012). DOI: 10.1016/S1003-6326(12)61729-4.
- S. Dicecco et al., Determination of forming limit diagrams of AA6013-T6 aluminum alloy sheet using a time and position dependent localized necking criterion, IOP Conf. Ser: Mater. Sci. Eng. 159 (1), 012009 (2016). DOI: 10.1088/1757-899X/159/1/012009.
- M. P. Sklad, Aspects of automated measurement of proportional and non-proportional deformation in sheet metal forming, J. Mater. Process Tech. 145 (3), 377 (2004). DOI: 10.1016/j.jmatprotec.2003.09.004.
- S. D. Kumar, T. R. Amjith, and C. Anjaneyulu, Forming limit diagram generation of aluminum alloy AA2014 using Nakazima test simulation tool, Proc. Tech. 24, 386 (2016). DOI: 10.1016/j.protcy.2016.05.053.
- T. Abovyan et al., Formability prediction of aluminum sheet alloys under isothermal forming conditions, J. Manuf. Process. 20, 406 (2015). DOI: 10.1016/j.jmapro.2014.08.003.
- ISO 12004-2:2008, Metallic materials-sheet and strip-determination of forming-limit curves. Part 2: determination of forming-limit curves in the laboratory, 2008. https://www.iso.org/standard/43621.html.
- X. R. Chu et al., Effecr of material thermo-viscoplastic modeling on the prediction of forming limit curves of aluminum alloy 5086, J. Mater. Eng. Perform. 24 (9), 3459 (2015). DOI: 10.1007/s11665-015-1643-6.
- F. Zhalehfar et al., A different approach for considering the effect of non-proportional loading path on the forming limit diagram of AA5083, Mater. Design. 50 (17), 165 (2013). DOI: 10.1016/j.matdes.2013.02.062.
- O. E. Fakir et al., Predicting effect of temperature, strain rate and strain path changes on forming limit of lightweight sheet metal alloys, Proc. Eng. 81, 736 (2014). DOI: 10.1016/j.proeng.2014.10.069.
- S. K. Paul, Path independent limiting criteria in sheet metal forming, J. Manuf. Process. 20, 291 (2015). DOI: 10.1016/j.jmapro.2015.06.025.