Porous Ni-YSZ planar anodes by powder extrusion moulding employing PMMA as pore former

References

• O. Yamamoto: ‘Solid oxide fuel cells: fundamental aspects and prospects’, Electrochim. Acta, 2000, 45, 2423–2435. doi: 10.1016/S0013-4686(00)00330-3
   Web of Science ®Google Scholar
• B. Shri Prakash, S. Senthil Kumar and S. T. Aruna: ‘Properties and development of Ni/YSZ as an anode material in solid oxide fuel cell: a review’, Renew. Sustainable Energy Rev., 2014, 36, 149–179. doi: 10.1016/j.rser.2014.04.043
   Web of Science ®Google Scholar
• F. Tietz, H. P. Buchkremer and D. Stöver: ‘Components manufacturing for solid oxide fuel cells’, Solid State Ion., 2002, 152–153, 373–381. doi: 10.1016/S0167-2738(02)00344-2
   Web of Science ®Google Scholar
• R. M. C. Clemmer and S. F. Corbin: ‘Influence of porous composite microstructure on the processing and properties of solid oxide fuel cell anodes’, Solid State Ion., 2004, 166, (3–4), 251–259. doi: 10.1016/j.ssi.2003.12.009
   Web of Science ®Google Scholar
• A. Manonukul, N. Muenya, F. Léaux and S. Amaranan: ‘Effects of replacing metal powder with powder space holder on metal foam produced by metal injection moulding’, J. Mater. Process. Technol., 2010, 210, (3), 529–535. doi: 10.1016/j.jmatprotec.2009.10.016
   Web of Science ®Google Scholar
• Y. Torres, J. J. Pavon and J. A. Rodríguez: ‘Processing and characterization of porous titanium for implants by using NaCl as space holder’, J. Mater. Process. Technol., 2012, 212, (5), 1061–1069. doi: 10.1016/j.jmatprotec.2011.12.015
   Web of Science ®Google Scholar
• G. L. Hao, Q. P. Xu, F. S. Han, W. D. Li and S. M. Bai: ‘Processing and damping behaviour of porous copper’, Powder Metall., 2009, 52, (2), 145–150. doi: 10.1179/003258908X356885
   Web of Science ®Google Scholar
• J. J. Haslam, A. Q. Pham, B. W. Chung, J. F. DiCarlo and R. S. Glass: ‘Effects of the use of pore formers on performance of an anode supported solid oxide fuel cell’, J. Am. Ceram. Soc., 2005, 88, (5), 13–18.
   Google Scholar
• W. Pabst, E. Gregorová, I. Sedlárová and M. Cerný: ‘Preparation and characterization of porous alumina-zirconia composite ceramics’, J. Eur. Ceram. Soc., 2011, 31, (14), 2721–2731. doi: 10.1016/j.jeurceramsoc.2011.01.011
   Web of Science ®Google Scholar
• G. Matula, T. Jardiel, B. Levenfeld and A. Várez: ‘Application of powder injection moulding and extrusion process to manufacturing of Ni-YSZ anodes’, JAMME., 2009, 36, (1), 87–94.
   Google Scholar
• H. Monzón, M. A. Laguna-Bercero, A. Larrea, B. I. Arias, A. Várez and B. Levenfeld: ‘Design of industrially scalable microtubular solid oxide fuel cells based on an extruded support’, Int. J. Hydrog. Energy, 2014, 39, 5470–5476. doi: 10.1016/j.ijhydene.2014.01.010
   Web of Science ®Google Scholar
• B. Arias-Serrano, M. E. Sotomayor, A. Várez, B. Levenfeld, H. Monzón, M. A. Laguna-Bercero and A. Larrea: ‘High performance Ni-YSZ thin-walled microtubes for anode-supported solid oxide fuel cells obtained by powder extrusion moulding’, RSC Adv., 2016, 6, (23), 19007–19015. doi: 10.1039/C5RA28183K
   Web of Science ®Google Scholar
• T. Jardiel, M. E. Sotomayor, B. Levenfeld and A. Várez: ‘Optimization of the processing of 8-YSZ powder by powder injection molding for SOFC electrolytes’, Int. J. Appl. Ceram. Technol., 2008, 5, (6), 574–581. doi: 10.1111/j.1744-7402.2008.02286.x
   Web of Science ®Google Scholar
• A. J. Poslinski, M. E. Ryan, R. K. Gupta, S. G. Seshadri and F. J. Frechette: ‘Rheological behavior of filled polymeric systems. 2. The effect of a bimodal size distribution of particulates’, J. Rheol., 1988, 32, (8), 751–771. doi: 10.1122/1.549991
   Web of Science ®Google Scholar
• B. C. Mutsuddy: ‘Injection molding research paves way to ceramic engine parts’, J. Ind. Res. Dev., 1993, 25, 76–80.
   Google Scholar
• S. Eroglu and H. I. Bakan: ‘Solvent debinding kinetics and sintered properties of injection moulded 316L stainless steel powder’, Powder Metall. Int., 2005, 48, (4), 329–332. doi: 10.1179/174329005X66782
   Web of Science ®Google Scholar