References
- Govindarajan N, Gnanamoorthy R. Rolling/sliding contact fatigue life prediction of sintered and sinterhardened steels. Wear. 2007;262:70–78. doi: 10.1016/j.wear.2006.03.053
- Govindarajan N, Gnanamoorthy R. Study of damage mechanisms and failure analysis in sintered and hardened steels under rolling/sliding contact conditions. Mater Sci Eng A. 2007;445–446:259–268. doi: 10.1016/j.msea.2006.09.039
- Bormetti E, Donzella G, Mazzù A. Surface and subsurface cracks in rolling contact fatigue of hardened components. J Tribol Trans. 2002;45:274–283. doi: 10.1080/10402000208982550
- Sadeghi F, Jalalahmadi B, Slack TS, et al. A review of rolling contact fatigue. J Tribol T ASME. 2009;13:1–15.
- Straffelini G, Molinari A, Marcupuscas T. Identification of rolling-sliding damage mechanisms in porous alloys. Metall Mater Trans A. 2000;31:3091–3099. doi: 10.1007/s11661-000-0088-0
- Muterlle PV, Straffelini G, Molinari A, et al. Microstructural effects in wear of hardened sintered steels produced by diffusion bonded and prealloyed powders. Powd Metall. 2010;53:201–207. doi: 10.1179/174329009X409732
- Bhattacharyya A, Subhash G, Arakere N. Evolution of subsurface plastic zone due to rolling contact fatigue of M-50 NiL case hardened bearing steel. Int J Fatigue. 2014;59:102–113. doi: 10.1016/j.ijfatigue.2013.09.010
- Straffelini G, Molinari A. Effect of hardness on rolling–sliding damage mechanisms in PM alloys. Powd Metall. 2001;44:344–350. doi: 10.1179/pom.2001.44.4.344
- Straffelini G, Menapace C, Molinari A. Interpretation of effect of matrix hardness on tensile and impact strength of sintered steels. Powd Metall. 2002;45(2):167–172. doi: 10.1179/003258902225002587
- Santuliana E, Cristofolini I, Molinari A, et al. Effect of shot peening on the fatigue resistance of a Cr-Mo sintered steel. Adv Powd Metall Part Mater. 2010;6:41–48.
- Molinari A, Santuliana E, Cristofolini I, et al. Surface modifications induced by shot peening and their effect on the plane bending fatigue strength of a Cr–Mo steel produced by powder metallurgy. Mater Sci Eng A. 2011;528:2904–2911. doi: 10.1016/j.msea.2010.12.072
- Metinöz I, Cristofolini I, Pahl W, et al. Theoretical and experimental study of the contact fatigue behaviour of a Mo-Cu steel produced by powder metallurgy. Mater Sci Eng A. 2014;614:81–87. doi: 10.1016/j.msea.2014.07.009
- Molinari A, Menapace C, Santuliana E, et al. A semplified model for the impact resistance of porous sintered steels. Powder Metall Prog. 2011;11:12–20.
- Chawla N, Deng X. Microstructure and mechanical behavior of porous sintered steels. Mater Sc Eng A. 2005;390(1):98–112. doi: 10.1016/j.msea.2004.08.046
- Cristofolini I, Cipolloni G, Molinari A. Macro- and micro-geometrical characteristics of surfaces of porous sintered parts. Adv Powd Metall Part Mater. 2012;2(7):47–56.
- Pohl D. On the fatigue strength of sintered iron. Powder Met Int. 1969;1:26–28.
- Bell T, Sun Y. Load bearing capacity of plasma nitrided steelunder rolling–sliding contact. Surf Eng. 1990;6:133–139. doi: 10.1179/sur.1990.6.2.133
- Smith JO, Liu CK. Stresses due to tangential and normal loads on an elastic solid with application to some contact stress problems. J Appl Mech. 1953;20:157–166.