Development of a new model describing the anisotropic dimensional change on sintering

References

• Cristofolini I, Menapace C, Cazzolli M, et al. The effect of anisotropic dimensional change on the precision of steel parts produced by Powder metallurgy. J Mater Proc Techn. 2012;212(7):1513–1519.
   Web of Science ®Google Scholar
• Wakai F, Shinoda Y. Anisotropic sintering stress for sintering of particles arranged in orthotropic symmetry. Acta Mater. 2009;57:3955–3964.
   Web of Science ®Google Scholar
• Wakai F, Akatsu T. Anistropic viscosities and shrinkage rate in sintering of particles arranged in simple orthorhombic structure. Acta Mater. 2010;58:1921–1929.
   Web of Science ®Google Scholar
• Olevsky EA, Kushnarev B, Maximenko A, et al. Modelling of anisotropic sintering in crystalline ceramics. Philos Mag. 2005;85:2123–2146.
   Web of Science ®Google Scholar
• Torresani E, Giuntini D, Zhu C, et al. Anisotropy of mass transfer during sintering of powder materials with pore–particle structure orientation. Metall Mater Trans A. 2019;50:1033–1049.
   Web of Science ®Google Scholar
• Zavaliangos A, Missiaen JM, Bouvard D. Anisotropy in shrinkage during sintering. Sci Sintering. 2006;38:13–25.
   Web of Science ®Google Scholar
• Zavaliangos A, Bouvard D. Numerical simulation of anisotropy in sintering due to prior compaction. Int J Powder Metall. 2000;36(7):59–65.
   Web of Science ®Google Scholar
• Molinari A, Zago M, Amirabdollhaian S, et al. From compaction mechanics to sintering shrinkage of rings with different H/(Dext-Dint) ratio. Adv Powder Metall Part Mater. 2018;1:81–90.
   Google Scholar
• Zago M, Cristofolini I, Molinari A. New interpretation for the origin of the anisotropic sintering shrinkage of AISI 316L rings based on the anisotropic stress field occurred on uniaxial cold compaction. Powder Metall. 2019;62(2):115–123.
   Web of Science ®Google Scholar
• Baselli S, Torresani E, Zago M, et al. Sintering shrinkage of uniaxial cold compacted iron: influence of the microstructure on the anisothermal and isothermal shrinkage. Powder Metall. 2018;61(4):276–284.
   Web of Science ®Google Scholar
• Cristofolini I, Pilla M, Larsson M, et al. A Doe analysis of dimensional change on sintering of a 3% Cr-0.5% Mo-X% C steel and its effect on dimensional and geometric precision. Powder Metall Prog. 2012;12(3):127–143.
   Google Scholar
• Cristofolini I, Pilla M, Rao A, et al. Dimensional and geometrical precision of powder metallurgy parts sintered and sinterhardened at high temperature. Int J Precis Eng Manuf. 2013;14(10):1735–1742.
   Web of Science ®Google Scholar
• Cristofolini I, Selber F, Menapace C, et al. Anisotropy of dimensional variation and its effect on precision of sintered parts. Proc. of Euro PM 2012 congress & exhibition, 2012.
   Google Scholar
• Cristofolini I, Pilla M, Molinari A, et al. A Doe investigation on anisotropic dimensional change on Fe-C-Cu sintering. Int J Powder Metall. 2012;48(4):37–43.
   Web of Science ®Google Scholar
• Wanibe Y, Yokoyama H, Itoh T. Expansion during liquid phase sintering of iron-copper compacts. Powder Metall. 1990;33(1):65–69.
   Web of Science ®Google Scholar
• Griffo A, Ko J, German R. Critical assessment of variables affecting the dimensional behavior in sintered iron-copper-carbon alloys. Adv Powder Metall Part Mater. 1994;3:221–236.
   Google Scholar
• Raman R, Zahrah T, Weaver T, et al. Predicting dimensional change during sintering of FC0208 parts. Adv Powder Metall Part Mater. 1999;1(3):115–122.
   Google Scholar
• Danninger H. Sintering of Mo alloyed PM steels prepared from elemental powders. II. Mo homogenization and dimensional behaviour. Powder Metall Int. 1992;24(3):163–168.
   Web of Science ®Google Scholar
• Cristofolini I, Corsentino N, Molinari A, et al. Study of the influence of material and geometry on the anisotropy of dimensional change on sintering of powder metallurgy parts. Int J Prec Eng Man. 2014;15(9):1865–1873.
   Web of Science ®Google Scholar
• Cristofolini I, Molinari A, Zago M, et al. Design for sintering club project – dealing with the anisotropy of dimensional changes in real parts. Proceedings EUROPM2018 Congress and Exhibition, Bilbao (Spain), 14-18 October 2018, ed. EPMA, Shrewsbury (UK), CD room.
   Google Scholar
• Cristofolini I, Molinari A, Zago M, et al. Design for powder metallurgy: predicting anisotropic dimensional change on sintering of real parts. Intl J Prec Eng Man. 2019;20(4):619–630.
   Web of Science ®Google Scholar
• ISO 10360-4. (2000). Geometrical product specifications (GPS), acceptance and reverification tests for coordinate measuring machines (CMM), Part 4: CMMs used in scanning measuring mode.
   Google Scholar
• Amirabdollahian S, Cristofolini I, Molinari A. coordinate measuring machines (CMM) in measurements of PM parts - influence of measurement strategy and data processing. Proceedings EuroPM2018. 2018. ISBN: 978-1-899072-50-7.
   Google Scholar
• Molinari A, Zago M, Amirabdollahian S, et al. Effect of geometry and green density on the anisotropic sintering shrinkage of axisymmetric iron parts. Powder Metall. 2018;61(4):267–278.
   Web of Science ®Google Scholar
• Molinari A, Cristofolini I, Pederzini G, et al. A densification equation derived from the stress deformation analysis of uniaxial cold compaction of metal powder mixes. Powder Metall. 2018;61(3):210–218.
   Web of Science ®Google Scholar