References
- Bader, R., J. Findlay, and T. M. Knowlton. 1988. “Gas/Solid Flow Patterns in a 30-5-cm Diameter Circulating Fluidized bed.” In Circulating Fluidized Bed Technology II, edited by P. Basu and J. F. Large, 123–137. Toronto: Pergamon Press.
- Bandrowski, J., and G. Kaczmarzyk. 1978. “Gas-to-Particle Heat Transfer in Vertical Pneumatic Conveying of Granular Materials.” Chemical Engineering Science 33: 1303–1310. doi: 10.1016/0009-2509(78)85111-2
- Bi, H. T., and L-S. Fan. 1991. “Regime Transitions in Gas–Solid Circulating Fluidized Beds.” A.I.Ch.E. annual meeting. AIChE, Los Angeles, pp. 17–22.
- Freitas, L. A. P., and J. T. Freire. 2001. “Gas-to-Particle Heat Transfer in the Draft Tube of a Spouted Bed.” Drying Technology. 19 (6): 1065–1082. doi: 10.1081/DRT-100104805
- Fyhr, C., and A. Rasmuson. 1997. “Steam Drying of Wood Chips in Pneumatic Conveying Dryers.” Drying Technology 15 (6-8): 1775–1785. doi: 10.1080/07373939708917326
- Issangya, A. S., D. Bai, H. T. Bi, K. S. Lim, J. Zhu, and J. R. Grace. 1999. “Suspension Densities in a High-Density Circulating Fluidized Bed Riser.” Chemical Engineering Science 54: 5451–5460. doi: 10.1016/S0009-2509(99)00283-3
- Jeevahan, Jeya, M. Chandrasekaran, G. Mageshwaran, and G. Britto Joseph. 2016. “Analysis of the Effect of Geometry of Vortex Tube on Cold side and Hot Side Air Stream Temperatures.” Journal of Chemical and Pharmaceutical Sciences 9 (3): 2474–2477. ISSN: 0974-2115
- Kaensup, W., S. Kulwong, and S. Wongwises. 2006. “Comparison of Drying Kinetics of Paddy Using a Pneumatic Conveying Dryer with and Without a Cyclone.” Drying Technology. 24 (8): 1039–1045. doi: 10.1080/07373930600776241
- Kim, S. W., G. Kirbas, H. Bi, C. J. Lim, and J. R. Grace. 2004. “Flow Behavior and Regime Transition in a High-Density Circulating Fluidized Bed Riser.” Chemical Engineering Science 59: 3955–3963. doi: 10.1016/j.ces.2004.06.018
- Kudra, T., A. S. Mujumdar, and G. S. V. Raghavan. 1989. “Gas-to-Particle Heat Transfer in Two-Dimensional Spouted Beds.” International Communications in Heat and Mass Transfer 16: 731–741. doi: 10.1016/0735-1933(89)90078-X
- Levy, A., and I. Borde. 1999. “Steady State One Dimensional Flow Model for a Pneumatic Dryer.” Chemical Engineering and Processing: Process Intensification 38: 121–130. doi: 10.1016/S0255-2701(98)00079-8
- Levy, A., D. J. Mason, D. Levi-Hevroni, and I. Borde. 1998. “Drying of Wet Solid Particles in a Steady-State One-Dimensional Flow.” Powder Technology 95: 15–23. doi: 10.1016/S0032-5910(97)03311-1
- Mageshwaran, G., Satyanarayana Rao Polisetti, Jeya Jeevahan, and G. Britto Joseph. “Enhancement of Uniform Temperature Distribution During Casting Solidification by Methoding Process.” International Journal of Ambient Energy. doi:doi: 10.1080/01430750.2016.1222959.
- Raju, A., V. Sita Rama, J. P. Subrahamanyam, T. R. Rao, and B. Pitchumani. 1994. “Gas–Solid Heat Transfer in Cyclone Heat Exchanger.” Indian Chemical Engineer Section A 36 (1-2): 58–62.
- Rhodes, M. J. 1990. “Modelling the Flow Structure of Upward-Flowing Gas–Solids Suspensions.” Powder Technology 60: 27–38. doi: 10.1016/0032-5910(90)80101-4