References
- Huang QX, Yang XR, Ma LF, et al. Interface correlated characteristics of stainless steel carbon steel plate fabricated by AAWIV and hot rolling. J Iron Steel Res Int. 2014;21(10):931–937.
- Liu BX, Yin FX, Dai XL, et al. The tensile behaviors and fracture characteristics of stainless steel clad plates with different interfacial status. Mat Sci Eng A-Struct. 2017;679:172–182.
- Khadadad A, Koçak M, Ventzke V. Mechanical and fracture characterization of a bi-material steel plate. Int J Press Vessel Pip. 2002;79:181–191.
- Li L, Yin FX, Nagai K. Progress of laminated materials and clad steels production. Mater Sci Forum. 2011;675-677:439–447.
- Marques MJ, Ramasamy A, Batista AC, et al. Effect of heat treatment on microstructure and residual stress fields of a weld multilayer austenitic steel clad. J Mater Process Technol. 2015;222:52–60.
- Mendes R, Ribeiro JB, Loureiro A. Effect of explosive characteristics on the explosive welding of stainless steel to carbon steel in cylindrical configuration. Mater Design. 2013;51:182–192.
- Jiang WC, Luo Y, Zhang GD, et al. Experimental to study the effect of multiple weld-repairs on microstructure, hardness and residual stress for a stainless steel clad plate. Mater Design. 2013;51:1052–1059.
- Dhib Z, Guermazi N, Gasperini M, et al. Cladding of low-carbon steel to austenitic stainless steel by hot-roll bonding: microstructure and mechanical properties before and after welding. Mat Sci Eng A-Struct. 2016;656:130–141.
- Jiang WC, Liu ZB, Gong JM, et al. Numerical simulation to study the effect of repair width on residual stresses of a stainless steel clad plate. Int J Press Vessel Pip. 2010;87(8):457–463.
- Venkateswara N, Madhusudhan G, Nagarjuna S. Weld overlay cladding of high strength low alloy steel with austenitic stainless steel structure and properties. Mater Design. 2011;32:2496–2506.
- Hajiannia I, Shamanian M, Kasiri M. Microstructure and mechanical properties of AISI 347 stainless steel/A335 low alloy steel dissimilar joint produced by gas tungsten arc welding. Mater Design. 2013;50:566–573.
- Wang SG, Dong GP, Ma QH. Welding of duplex stainless steel composite plate: influence on microstructural development. Mater Manuf Proc. 2009;24(12):1383–1388.
- Rajeev R, Samajdar I, Raman R, et al. Origin of hard and soft zone formation during cladding of austenitic/duplex stainless steel on plain carbon steel. Mater Sci Technol. 2001;17(8):1005–1011.
- Jiang WC, Wang BY, Gong JM, et al. Finite element analysis of the effect of welding heat input and layer number on residual stress in repair welds for a stainless steel clad plate. Mater Design. 2011;32(5):2851–2857.
- Chen CX, Liu MY, Liu BX, et al. Tensile shear sample design and interfacial shear strength of stainless steel clad plate. Fusion Eng Des. 2017;125:431–441.
- Missori S, Murdolo F, Sili A. Single-pass laser beam welding of clad steel plate. Welding J. 2004;83:65–71.
- Moteshakker A, Danaee I. Microstructure and corrosion resistance of dissimilar weld-joints between duplex stainless steel 2205 and austenitic stainless steel 316L. J Mater Sci Technol. 2016;32(3):282–290.
- Brooks JA, Williams JC, Thompson AW. Microstructural origin of the skeletal ferrite morphology of austenitic stainless steel welds. Metall Trans A. 1983;14(7):1271–1281.
- Xie GM, Luo ZA, Wang GL, et al. Interface characteristic and properties of stainless steel/HSLA steel clad plate by vacuum rolling cladding. Mater Trans. 2011;8:1709–1712.
- Schaeffler AL. Constitution diagram for stainless steel weld metal. Met Prog. 1949;56:680–680.
- Nouri M, Abdollah-Zadeh A, Malek F. Effect of welding parameters on dilution and weld bead geometry in cladding. Mater Sci Technol. 2007;23:817–822.
- Paventhan R, Lakshminarayanan PR, Balasubramanian V. Optimization of friction welding process parameters for joining carbon steel and stainless steel. J Iron Steel Res Int. 2012;19(1):66–71.
- Li BM, Xu GM, Cui JZ. Inversion solidification cladding of H90-steel. J Iron Steel Res Int. 2008;15:51–56.
- Su H, Luo XB, Chai F, et al. Manufacturing technology and application trends of titanium clad steel plates. J Iron Steel Res Int. 2015;22(11):977–982.
- Mas F, Tassin C, Valle N, et al. Metallurgical characterization of coupled carbon diffusion and precipitation in dissimilar steel welds. J Mater Sci. 2016;51(10):4864–4879.
- Lou YS, Yoon JW, Huh H, et al. Correlation of the maximum shear stress with micro-mechanisms of ductile fracture for metals with high strength-to-weight ratio. Int J Mech Sci. 2018;146–147:583–601.
- Jones R, Singh Raman RK, Mcmillan AJ. Crack growth: does microstructure play a role? Eng Fract Mechan. 2018;187:190–210.
- Zhou ST, Li ZD, Yang CF, et al. Cleavage fracture and microstructural effects on the toughness of a medium carbon pearlitic steel for high-speed railway wheel. Mater Sci Eng A. 2019;761:138036.
- Lawn B. Fracture of brittle solids. Cambridge (UK): Cambridge University Press; 1993. p. 1–378.