References
- J. Chakraborty and I. Manna: ‘Development of ultrafine ferritic sheaves/plates in SAE 52100 steel for enhancement of strength by controlled thermomechanical processing’, Mater. Sci. Eng. A, 2012, 548, 33–42.
- N. Luzginova, L. Zhao and J. Sietsma: ‘Evolution and thermal stability of retained austenite in SAE 52100 bainitic steel’, Mater. Sci. Eng. A, 2007, 448, 104–110.
- Ł. Rogal and J. Dutkiewicz: ‘Effect of annealing on microstructure, phase composition and mechanical properties of thixo-cast 100Cr6 steel’, Mater. Charact., 2012, 68, 123–130.
- L. Rogal and J. Dutkiewicz: ‘Transmission electron microscopy studies of X210CrW12 and 100Cr6 thixo-cast steels', Solid State Phenom., 2012, 186, 311–314.
- F. Yin, L. Hua, H. Mao, X. Han, D. Qian and R. Zhang: ‘Microstructural modeling and simulation for GCr15 steel during elevated temperature deformation’, Mater. Des., 2013, 55, 560–573.
- F. Yin, L. Hua, H. Mao and X. Han: ‘Constitutive modeling for flow behavior of GCr15 steel under hot compression experiments', Mater. Des., 2013, 43, 393–401.
- R. Łukasz, G. Korpala and J. Dutkiewicz: ‘Evolution of microstructure in 100Cr6 steel after cooling from a thixoforming temperature to bainitic transformation ranges', Mater. Sci. Eng. A, 2015, 624, 291–299.
- Z. X. Li, C. S. Li, J. Y. Ren, J. Zhang and Y. Q. Ma: ‘Effect of cold deformation on the microstructure and impact toughness during the austenitizing process of 1.0C–1.5Cr bearing steel’, Mater. Sci. Eng. A, 2016, 674, 262–269.
- J. Guo, D. S. Dian and J. D. Deng: ‘Grain refinement limit during hot radial ring rolling of as-cast GCr15steel’, J. Mater. Process. Technol., 2016, 231, 151–161.
- D. S. Qian and Y. Pan: ‘3D coupled macro-microscopic finite element modelling and simulation for combined blank-forging and rolling process of alloy steel large ring’, Comput. Mater. Sci., 2013, 70, 24–36.
- D. S. Qian, Z. Q. Zhang and L. Hua: ‘An advanced manufacturing method for thick-wall and deep-groove ring-combined ring rolling’, J. Mater. Process. Technol., 2013, 213, 1258–1267.
- D. S. Qian, L. Hua and J. D. Deng: ‘FE analysis for radial spread behavior in three-roll cross rolling with small-hole and deep-groove ring’, Trans. Nonferr. Met. Soc. China, 2012, 22, 247–253.
- G. Zhou, L. Hua, D. S. Qian, D. F. Shi and H. X. Li: ‘Effects of axial rolls motions on radial-axial rolling process for large-scale alloy steel ring with 3D coupled thermo-mechanical FEA’, Int. J. Mech. Sci., 2012, 59, 1–7.
- J. J. Sun, F. L. Lian, H. J. Liu, T. Jiang, S. W. Guo and L. X. Du: ‘Microstructure of warm rolling and pearlitic transformation of ultrafine-grained GCr15 steel’, Mater. Charact., 2014, 95, 291–298.
- K. Ryttberg, M. K. Wedel, V. Recina, P. Dahlman and L. Nyborg: ‘The effect of cold ring rolling on the evolution of microstructure and texture in 100Cr6 steel’, Mater. Sci. Eng. A, 2010, 527, 2431–2436.
- W. T. Wei and M. Wu: ‘Effect of annealing cooling rate on microstructure and mechanical property of 100Cr6 steel ring manufactured by cold ring rolling process', J. Central South Univ., 2014, 21, 14–19.
- D. S. Qian, L. Hua and L. B. Pan: ‘Research on gripping conditions in profile ring rolling of raceway groove’, J. Mater. Process. Technol., 2009, 209, 2794–2802.
- J. Guo, S. Amira, P. Gougeon and X. G. Chen: ‘Effect of the surface preparation techniques on the EBSD analysis of a friction stir welded AA1100-B4C metal matrix composite’, Mater. Charact., 2011, 62, 865–877.
- L. Hua, D. S. Qian and L. B. pan: ‘Analysis of plastic penetration in process of groove ball-section ring rolling’, J. Mech. Sci. Technol., 2008, 22, 1374–1382.
- A. Leiro, A. Kankanala, E. Vuorinen and B. Prakash: ‘Tribological behaviour of carbide-free bainitic steel under dry rolling/sliding conditions', Wear, 2011, 273, 2–8.
- S. H. Choi and Y. S. Jin: ‘Evaluation of stored energy in cold-rolled steels from EBSD data’, Mater. Sci. Eng. A, 2004, 371, 149–159.
- A. J. Wilkinson and B. L. Adams: ‘Measuring strains using electron backscatter diffraction’ in ‘Electron backscatter diffraction in material Science’, (ed. A. J. Schwartz and M. Kumar), 231–246; 2000, New York, Kluwer Academic/Plenum Publishers.