References
- Ay I, Çelik S, Çelik I. Comparison of properties of friction and diffusion welded joints made between the pure aluminum and copper bars. Yayinlanmamis Yuksek lisans Tezi, Balikesir Universitesi; 1999, 89.
- Beigi R, Kazeminezhad M, Kokabi AH. Butt joining of Al-Cu bilayer sheet through friction stir welding. Trans Nonferr Met Soc China. 2012;22:2925–2929. doi: 10.1016/S1003-6326(11)61555-0
- Sharma N, Khan ZA, Siddiquee AN. Friction stir welding of aluminum to copper: an overview. Trans Nonferr Met Soc China. 2017;27:2113–2136. doi: 10.1016/S1003-6326(17)60238-3
- Chen CY, Hwang WS. Effect of annealing on the interfacial structure of aluminum-copper joints. Mater Trans. 2007;48:1938–1947. doi: 10.2320/matertrans.MER2006371
- Zare GR, Divandari M, Arabi H. Investigation on interface of Al/Cu couples in compound casting. Mater Sci Technol. 2013;29:190–196. doi: 10.1179/1743284712Y.0000000096
- Papkala H, Pietras A. Pressure welding of aluminum to copper. Weld Int. 2006;20:173–182. doi: 10.1533/wint.2006.3571
- Mazurkiewicz B, Piotrowski A. The electrochemical behavior of the Al2Cu intermetallic compound. Corr Sci. 1983;23:697–707. doi: 10.1016/0010-938X(83)90034-3
- Sahin M. Joining of aluminium and copper materials with friction welding. Int J Adv Manuf Technol. 2010;49:527–534. doi: 10.1007/s00170-009-2443-7
- Bhamji I, Moat RJ, Preuss M, et al. Linear friction welding of aluminum to copper. Sci Tech Weld Joi. 2012;17:314–320. doi: 10.1179/1362171812Y.0000000010
- Pan L, Li P, Hao X, et al. Inhomogeneity of microstructure and mechanical properties in radial direction of aluminum/copper friction welded joints. J Mat Proc Tech. 2018;255:308–318. doi: 10.1016/j.jmatprotec.2017.12.027
- Hussain T, McCartney DG, Shipway PH. Bonding between aluminum and copper in cold spraying: story of asymmetry. Mater Sci Technol. 2012;28:1371–1378. doi: 10.1179/1743284712Y.0000000051
- Tsakiris WK, Alecu G. Solid state diffusion welding of Cu-Fe/Al/Ag and Al-Ni dissimilar metals. J Optoelectronics Adv Mater. 2011;13:1176–1180.
- Galvao I, Oliveira JC, Loureiro A, et al. Formation and distribution of brittle structures in friction stir welding of aluminum and copper: influence of process parameters. Sci Technol Weld Joi. 2011;16:681–688. doi: 10.1179/1362171811Y.0000000057
- Mehta KP, Badheka VJ. A review on dissimilar friction stir welding of copper to aluminum: process, properties and variants. Mater Manuf Proc. 2016;31:233–254. doi: 10.1080/10426914.2015.1025971
- Mehta KP, Badheka VJ. Effect of tilt angle on properties of dissimilar friction stir welding copper to aluminum. Mater Manuf Proc. 2016;31:255–263. doi: 10.1080/10426914.2014.994754
- Abbasi M, Karimi Taheri A, Salehi MT. Growth rate of intermetallic compounds in Al/Cu bimetal produced by cold roll welding process. J Alloys Compd. 2001;319:233–241. doi: 10.1016/S0925-8388(01)00872-6
- Yang YH, Lin GY, Chen DD, et al. Fabrication of Al-Cu laminated composites by diffusion rolling procedures. Mater Sci Technol. 2014;30:973–976. doi: 10.1179/1743284713Y.0000000397
- Carvalho GHSFL, Galvãoa I, Mendesc R, et al. Influence of base material properties on copper and aluminium–copper explosive welds. Sci Technol Weld Joi. 2018;23(6):501–507. doi: 10.1080/13621718.2017.1417783
- Ni ZL, Ye FX. Dissimilar joining of aluminum to copper using ultrasonic welding. Mater Manuf Proc. 2016;31:2091–2100. doi: 10.1080/10426914.2016.1221101
- Ozlati A, Movahedi M, Mohammadkamal H. Upset resistance welding of carbon steel to austenitic stainless steel narrow rods. J Mater Eng Perform. 2016;25:4902–4910. doi: 10.1007/s11665-016-2321-z
- Halvaee A, Sharifitabar M, Khorshahian S. Microstructure and mechanical properties of resistance upset butt welded 304 austenitic stainless steel joints. Mater Des. 2011;32:3854–3864. doi: 10.1016/j.matdes.2011.03.007
- ASM International. Metals handbook vol. 2: properties and selection: nonferrous alloys and special purpose materials. 10th ed. Geauga county (Ohio)United states: ASM International; 1990. p. 574. 917.
- Kerstens NFH, Richardson IM. Heat distribution in resistance upset butt welding. J Mater Process Technol. 2009;209:2715–2722. doi: 10.1016/j.jmatprotec.2008.06.015
- Zhang Y, Yamane T, Hirao K, et al. Microstructures and Vickers hardness of rapidly solidified Al-Cu alloys near the Al-Al2Cu equilibrium eutectic composition. J Mater Sci. 1991;26:5799–5805. doi: 10.1007/BF01130117