References
- Bai Y, Wang ZH, Li XB, et al. Corrosion behavior of low pressure cold sprayed Zn-Ni composite coatings. J Alloys Compd. 2017;719:194–202. doi: 10.1016/j.jallcom.2017.05.134
- Lu X, Wang S, Xiong T, et al. Anticorrosion properties of Zn-Al composite coating prepared by cold spraying. Coatings. 2019;9(3):210–220. doi: 10.3390/coatings9030210
- Cervantes J, Barba A, Hernandez MA, et al. Development of Zn-Al-Cu coatings by hot dip coated technology: preparation and characterization. Revista de metalurgia. 2013;49(5):351–359. doi: 10.3989/revmetalm.1316
- Bai Y, Wang Z, Li X, et al. Microstructure and mechanical properties of Zn-Ni-Al₂O₃ composite coatings. Materials (Basel). 2018;11(5):853–867. doi: 10.3390/ma11050853
- Wang X, Chen Y, Yu C, et al. Preparation and application of ZrC-coated flake graphite for Al2O3-C refractories. J Alloys Compd. 2019;788:739–747. doi: 10.1016/j.jallcom.2019.02.239
- Hernandez MA, Bakoglidis KD, Xiao P. A new slurry infiltration method to enhance the wear resistance of bulk graphite with development of reinforced graphitic composites including SiC or Si3N4 hard particles. J Eur Ceram Soc. 2019;39(6):1984–1992. doi: 10.1016/j.jeurceramsoc.2019.01.053
- Chen J, Zhang Q, Hou Z, et al. Preparation and characterization of graphite/thermosetting composites. Bull Mater Sci. 2019;42(4):153–157. doi: 10.1007/s12034-019-1844-y
- Hariharasakthisudhan P, Moshi AAM, Bharathi SRS, et al. Regression and grey relational analysis on friction and wear behavior of AA6061/Al2O3/Si3N4/ graphite hybrid nano composites. Mater Res Express. 2019;6(8):5017–5030. doi: 10.1088/2053-1591/ab1cd3
- Koc R, Ozkececi S. The fabrication of exfoliated graphite sheet-based air cathodes and gel electrolyte for metal-air batteries. Energy Sources, Part A: Recovery, Utilization, Environ Effects. 2019;41(14):1780–1790. doi: 10.1080/15567036.2018.1549154
- Sánchez Egea AJ, Martynenko V, Abate G, et al. Friction capabilities of graphite-based lubricants at room and over 1400 K temperatures. Int J Adv Manuf Technol. 2019;102(5):1623–1633. doi: 10.1007/s00170-019-03290-4
- Huang C, Li W, Xie Y, et al. Effect of substrate type on deposition behavior and wear performance of Ni-coated graphite/Al composite coatings deposited by cold spraying. J Mater Sci Technol. 2017;33(4):338–346. doi: 10.1016/j.jmst.2016.11.016
- Deng N, Tang J, Xiong T, et al. Fabrication and characterization of W-Cu composite coatings with different W contents by cold spraying. Surf Coat Technol. 2019;368:8–14. doi: 10.1016/j.surfcoat.2019.04.034
- Machethe KE, Popoolab API, Adebiyi DI, et al. Influence of SiC-Ti/Al on the microstructural and mechanical properties of deposited Ti-6V-4A1 alloy with cold spray technique. Procedia Manuf. 2017;7:549–555. doi: 10.1016/j.promfg.2016.12.069
- Koivuluoto H, Coleman A, Murray K, et al. High pressure cold sprayed (HPCS) and low pressure cold sprayed (LPCS) coatings prepared from OFHC Cu feedstock: overview from powder characteristics to coating properties. J Therm Spray Technol. 2012;21(5):1065–1075. doi: 10.1007/s11666-012-9790-x
- Xie X, Chen C, Xie Y, et al. Comparative investigation of microstructure and properties of Ni-coated FeSiAl soft magnetic composite coatings produced by cold spraying and HVOF. Surf Coat Technol. 2018;371:224–234. doi: 10.1016/j.surfcoat.2018.12.067
- Tariq NU, Gyansah L, Qiu X, et al. Achieving strength-ductility synergy in cold spray additively manufactured Al/B4C composites through a hybrid post-deposition treatment. J Mater Sci Technol. 2019;35(6):1053–1063. doi: 10.1016/j.jmst.2018.12.022
- Yin S, Li W, Song B, et al. Deposition of FeCoNiCrMn high entropy alloy (HEA) coating via cold spraying. J Mater Sci Technol. 2019;35(6):1003–1007. doi: 10.1016/j.jmst.2018.12.015
- Shaha SK, Dayani SB, Xue YN, et al. Improving corrosion and corrosion-fatigue resistance of AZ31B Cast Mg alloy using combined cold spray and top coatings. Coatings. 2018;8(12):403–425. doi: 10.3390/coatings8120443
- Bedard BA, Flanagan TJ, Ernst AT, et al. Microstructure and micromechanical response in gas-atomized Al 6061 alloy powder and cold-sprayed splats. J Therm Spray Technol. 2018;27(8):1563–1578. doi: 10.1007/s11666-018-0785-0
- Jenkins R, Aldwell B, Yin S, et al. Solid state additive manufacture of highly-reflective Al coatings using cold spray. Opt Laser Technol. 2019;115:251–256. doi: 10.1016/j.optlastec.2019.02.011
- Nikbakhta R, Seyedeinb SH, Kheirandishc S, et al. The role of deposition sequence in cold spraying of dissimilar materials. Surf Coat Technol. 2019;367:75–85. doi: 10.1016/j.surfcoat.2019.03.065