References
- Lee HC, Jung YS, Oh HJ, et al. Design of a hybrid composite strut tower for use in automobiles. Adv. Compos. Mater. 2014;23:275–291.10.1080/09243046.2013.868664
- Shiva E, Esmaeel RA, Taheri F. Experimental investigation of the effect of aging on perforated composite tubes under axial compressive loading. Adv. Compos. Mater. 2013;22:151–164.
- Hibbeler RC. Mechanics of material. Upper Saddle River (NJ): Prentice Hall; 2003.
- Gummadi S, Kumar AJ. Optimum design and analysis of a composite drive shaft for an automobile. Karlskrona: Blekinge Institute of Technology; 2007.
- Shokrieh MM, Hasani A, Lessard LB. Shear buckling of a composite drive shaft under torsion. Compos. Struct. 2004;64:63–69.
- Khalid YA, Mutasher SA, Sahari BB, et al. Bending fatigue behavior of hybrid aluminum/composite drive shafts. Mater. Des. 2007;28:329–334.10.1016/j.matdes.2005.05.021
- Mutasher SA. Prediction of the torsional strength of the hybrid aluminum/composite drive shaft. Mater. Des. 2009;30:215–220.10.1016/j.matdes.2008.05.024
- Srinivasa Moorthy R, Mitiku Y, Sridhar K. Design of automobile driveshaft using carbon/epoxy and kevlar/epoxy composites. Am. J. Eng. Res. 2013;2:173–179.
- Cherniaev A, Komarov V. Multistep optimization of composite drive shaft subject to strength, buckling, vibration and manufacturing constraints. Appl. Compos. Mater. 2015;22:475–487.10.1007/s10443-014-9418-z
- Montagnier O, Hochard C. Optimisation of hybrid high-modulus/high-strength carbon fibre reinforced plastic composite drive shafts. Mater. Des. 2013;46:88–100.10.1016/j.matdes.2012.09.035
- Khalkhali A, Nikghalb E, Norouzian M. Multi-objective optimization of hybrid carbon/glass fiber reinforced epoxy composite automotive drive shaft. Int. J. Eng. 2015;28:583–592.
- Kalsule D, Vikram M, Ambardekar M, et al. Reduction of in-cab boom and transmission rattling using cost effective driveline refinement. SAE. 2011. doi:10.4271/2011-26-0060.
- Sorniotti A. Driveline modeling, experimental validation and evaluation of the influence of the different parameters on the overall system dynamics. SAE. 2008. doi:10.4271/2008-01-0632.
- Abu Talib AR, Ali A, Badie MA, et al. Developing a hybrid, carbon/glass fiber-reinforced, eposy composite automotive drive shaft. Mater. Des. 2010;31:514–521.
- Badie MA, Mahdi E, Hamouda AMS. An investigation into hybrid carbon/glass fiber reinforced epoxy composite automotive drive shaft. Adv. Compos. Mater. 2011;32:1485–1500.10.1016/j.matdes.2010.08.042
- Ito Y, Obo T, Minakuchi S, et al. Cure strain in thick CFRP laminate: optical-fiber-based distributed measurement and numerical simulation. Adv. Compos. Mater. 2015;24:325–342.10.1080/09243046.2014.906914
- Takagaki K, Minakuchi S, Takeda N. Fiber-optic-based life-cycle monitoring of through-thickness strain in thick CFRP pipes. Adv. Compos. Mater. 2014;23:195–209.
- Mallick PK. Fiber-reinforced composites: materials, manufacturing, and design. Boca Raton (FL): Taylor & Francis Group; 2007.10.1201/CRCDEKMECENG
- Kim Y, Chun Y, Cheon SS. Shear directional impact characteristics of adhesively bonded tubular joints. Adv. Compos. Mater. 2015;24:287–295.
- Purimpat S, Rousseau J, Aivazzadeh S. Effect of fiber angle orientation on a laminated composite single-lap adhesive joint. Adv. Compos. Mater. 2013;22:139–149.