Mechanical properties characterisation of welded joint of austenitic stainless steel using instrumented indentation technique

References

• K. Shin-ichi and K. Taichiro: ‘Creep properties measurements of heat-affected zones of high Cr ferritic steel by SP creep test’, Mater. High. Temp., 2010, 27, 205–209.
   Web of Science ®Google Scholar
• J. H. Ahn and D. Kwon: ‘Derivation of plastic stress–strain relationship from ball indentations: examination of strain definition and pileup effect’, J. Mater. Res., 2001, 16, 3170–3178.10.1557/JMR.2001.0437
   Web of Science ®Google Scholar
• J. Y. Kim, K. W. Lee, J. S. Lee and D. Kwon: ‘Determination of tensile properties by instrumented indentation technique: representative stress and strain approach’. Surf. Coat. Technol., 2006, 201, 4278–4283.10.1016/j.surfcoat.2006.08.054
   Web of Science ®Google Scholar
• K. L. Murty and M. D. Mathew: ‘Nondestructive monitoring of structural materials using automated ball indentation (ABI) technique’, Nucl. Eng. Des., 2004, 228, 81–96.10.1016/j.nucengdes.2003.06.006
   Web of Science ®Google Scholar
• J. I. Jang, Y. Choi, J. S. Lee, Y. H. Lee, D. Kwon, M. Gao and R. Kania: ‘Application of instrumented indentation technique for enhanced fitness-for-service assessment of pipeline crack’. Int. J. Fract., 2005, 131, 15–33.10.1007/s10704-004-1690-8
   Web of Science ®Google Scholar
• S. Ghosh, T. K. Pal, S. Mukherjee, G. Das and S. Ghosh: ‘Comparative study of heat-affected zone with weld and base material after post-weld heat treatment of HSLA steel using ball indentation technique’, J. Mater. Sci., 2008, 43, 5474–5482.10.1007/s10853-008-2840-6
   Web of Science ®Google Scholar
• K. H. Chung, W. Lee, J. H. Kim, C. Kim, S. H. Park, D. Kwon and K. Chung: ‘Characterization of mechanical properties by indentation tests and FE analysis–validation by application to a weld zone of DP590 steel’. Int. J. Solids Struct., 2009, 46, 344–363.10.1016/j.ijsolstr.2008.08.041
   Web of Science ®Google Scholar
• K. W. Lee, K. H. Kim, J. Y. Kim, K. H. Kim, B. H. Choi and D. Kwon: ‘Safety assessment based on mapping of degraded mechanical properties of materials for power plant pipeline using instrumented indentation technique’, J. Loss Prev. Process Ind., 2009, 22, 868–872.10.1016/j.jlp.2008.09.007
   Web of Science ®Google Scholar
• A. S. Hamada, F. M. Haggag and D. A. Porter: ‘Non-destructive determination of the yield strength and flow properties of high-manganese twinning-induced plasticity steel’, Mater. Sci. Eng. A, 2012, 558, 766–770.10.1016/j.msea.2012.08.066
   Web of Science ®Google Scholar
• C. Ullner, S. Brauser, A. Subaric-Leitis, G. Weber and M. Rethmeier: ‘Determination of local stress–strain properties of resistance spot-welded joints of advanced high-strength steels using the instrumented indentation test’, J. Mater. Sci., 2012, 47, 1504–1513.10.1007/s10853-011-5936-3
   Web of Science ®Google Scholar
• M. Yetna N’Jock, D. Chicot, X. Decoopman, J. Lesage, J. M. Ndjaka and A. Pertuz: ‘Mechanical tensile properties by spherical macroindentation using an indentation strain-hardening exponent’, Int. J. Mech. Sci., 2013, 75, 257–264.10.1016/j.ijmecsci.2013.07.008
   Web of Science ®Google Scholar
• D. C. Ludwigson: ‘Modified stress-strain relation for FCC metals and alloys’, Metall. Trans., 1971, 2, 2825–2828.10.1007/BF02813258
   Web of Science ®Google Scholar
• S. B. Wu and K. S. Guan: ‘Evaluation of tensile properties of austenitic stainless steel 316L with linear hardening by modified indentation method’. Mater. Sci. Tech., 2014, 30, 1404–1409.10.1179/1743284713Y.0000000469
   Web of Science ®Google Scholar
• S. H. Kim, B. W. Lee, Y. Choi and D. Kwon: ‘Quantitative determination of contact depth during spherical indentation of metallic materials – a FEM study’. Mater. Sci. Eng. A, 2006, 415, 59–65.10.1016/j.msea.2005.08.217
   Web of Science ®Google Scholar
• D. Tabor: ‘The hardness of metals’, 1951, Oxford, Clarendon Press.
   Google Scholar
• H. A. Francis: ‘Phenomenological analysis of plastic spherical indentation’, J. Eng. Mater. Technol., 1976, 98, 272–281.10.1115/1.3443378
   Web of Science ®Google Scholar
• R. A. George, S. Dinda and A. S. Kasper: ‘Estimating yield strength from hardness data’, Met. Prog., 1976, 109, 30–33.
   Google Scholar
• G. E. Dieter: ‘Mechanical metallurgy’, 1986, New York, McGraw-Hill.
   Google Scholar
• ‘Metallic materials – measurement of mechanical properties by an instrumented indentation test – indentation tensile properties’, ISO/TR 29381:2008.
   Google Scholar
• ‘Standard test methods for tension testing of metallic materials’, E8M-11, ASTM, USA, 2011.
   Google Scholar
• S. Katayama, T. Fujimoto and A. Matsunawa: ‘Correlation among solidification process, microstructure, microsegregation and solidification cracking susceptibility in stainless steel weld metals’, Trans. JWRI, 1985, 14, 123–138.
   Google Scholar
• J. W. Fu and Y. S. Yang: ‘Origin of the lathy ferrite in AISI 304 stainless steel during directional solidification’, J. Alloys Comp., 2013, 580, 191–194.10.1016/j.jallcom.2013.05.107
   Web of Science ®Google Scholar
• D. Hauser and J. E. Vanecho: ‘Effects of ferrite content in austenitic stainless steel welds’. Weld. J., 1982, 61, 37–44.
   Web of Science ®Google Scholar
• W. C. Oliver and G. M. Pharr: ‘Measurement of hardness and elastic modulus by instrumented indentation: advances in understanding and refinements to methodology’. J. Mater. Res., 2004, 19, 3–20.10.1557/jmr.2004.19.1.3
   Web of Science ®Google Scholar
• S. Kumar and A. S. Shahi: ‘Effect of heat input on the microstructure and mechanical properties of gas tungsten arc welded AISI 304 stainless steel joints’, Mater. Des., 2011, 32, 3617–3623.10.1016/j.matdes.2011.02.017
   Web of Science ®Google Scholar
• N. Arivazhagan, S. Singh, S. Prakash and G. M. Reddy: ‘Investigation on AISI 304 austenitic stainless steel to AISI 4140 low alloy steel dissimilar joints by gas tungsten arc, electron beam and friction welding’, Mater. Des., 2011, 32, 3036–3050.10.1016/j.matdes.2011.01.037
   Web of Science ®Google Scholar