References
- Oka M, Ambarita H, Daimaruya M, et al. Study on the effects of switching temperature on the thermal fatigue life of the shell-to-skirt junction of coke drum. J. Pressure Vessel Technol 2011;133(6):061210.
- Yamamoto T, Arii K, Niimoto S, et al. Investigation of bulging behavior of coke drum—A practical analysis of bulging under complex quench conditions. J. Pressure Vessel Technol 2014;136(6):061401.
- Ohata M, Kawai N, Tagawa T, et al. Investigation of bulging behavior of coke drum: feasible study on causes of bulging. J. Pressure Vessel Technol 2014;136(3):031205.
- Nikic M, Xia Z, Plessis PD. Assessment of coke drum materials based on ASME material property data. J. Pressure Vessel Technol 2015;137(6):061401.
- Oka M, Ambarita H, Daimaruya M, et al. Initiation of bulges in a coke drum subjected to cyclic heating and cooling, also cyclic mechanical loads. J. Therm. Stresses 2010;33(10):964–976.
- Ju F, Aumuller J, Xia Z, et al. Global and local elastic-plastic stress analysis of coke drum under thermal-mechanical loadings. J. Pressure Vessel Technol 2011;133(6):061202.
- Wang Y, Kannan R, Li L, et al. Jagged cracking in the heat-affected zone of weld overlay on coke drum cladding. Eng Fail Anal. 2018;85:14–25.
- Xia Z, Ju F, Plessis PD. Heat transfer and stress analysis of coke drum for a complete operating cycle. J. Pressure Vessel Technol 2010;132(5):051205.
- Li L, Kannan R, Wang Y, et al. Microstructural aging and property degradation of service-exposed 1Cr–1/2Mo Coke Drum steel. Mater Sci Technol. 2020;36(18):1943–1953.
- Chen J, Xia Z. A fatigue life prediction method for coke drum base, weld, and HAZ materials from tensile properties. Mater Des. 2014;63,575–83.
- ASTM A387/A387M-17. Standard specification for pressure vessel plates, alloy steel, chromium-molybdenum. West Conshohocken: ASTM International; 2017.
- Feng D. A Dictionary of Solid State Physics. Beijing: Higher Education Press; 1995.
- ASTME2368-10. 2010. Standard Practice for Strain Controlled Thermomechanical Fatigue Testing. West Conshohocken: ASTM International.
- Hähner P, Affeldt E, Beck T, et al. Validated code-of-practice for strain-controlled thermo-mechanical fatigue testing. Brussels: EUR 22281 EN-DG JRC-Institute for Energy; 2006.
- GB/T33812-2017. Metallic Material—Fatigue Testing—Strain-controlled Thermomechanical Fatigue Testing Method. Beijing: AQSIQ; 2017.
- Kadioglu Y, Sehitoglu H. Thermomechanical and isothermal fatigue behavior of bare and coated superalloys. J. Eng. Mater. Technol. 1995. 117(1):94–102.
- Zw H. Isothermal low-cycle fatigue and thermomechanical fatigue behavior of MCrAlY coated and uncoated nickel base superalloy. Dalian: DUT; 2008.
- Lh Z. Low cycle fatigue and thermo-mechanical fatigue behavior from 600°C to 950°C in heat-resistant austenitic cast steel for automobiles application. Beijing: USTB; 2018.
- HJ C, Jung A, Maier HJ, et al. Thermomechanical fatigue—damage mechanisms and mechanism-based life prediction methods. Sadhana. 2003;28(1):147–165.
- Gocmez T, Awarke A, Pischinger S, et al. Cycle fatigue criterion for isothermal and Out-of-Phase thermomechanical loading. Int J Fatigue. 2010;32(4):769–779.
- Birks N, Meier GH, Pettit FS. Introduction to high temperature oxidation of metals. Cambridge: Cambridge University Press; 2006.
- API technical report 934G. design, fabrication, inspection, assessment, and repair of coke drums and peripheral components in delayed coking units. New York: API; 2016.