REFERENCE
- Krantz, T.L. and Kahraman, A. (2004), “An Experimental Investigation of the Influence of the Lubricant Viscosity and Additives on Gear Wear,” Tribology Transactions, 47(1), pp 138–148.
- Niemann, G. and Winter, H. (2003), Maschinenelemente, Band 2: Getriebe Allgemein, Zahnradgetriebe—Grundlagen, Stirnradgetriebe, Berlin: Springer Verlag.
- AGMA 912-A04. (2004), Mechanisms of Gear Tooth Failures, Alexandria, VA: American Gear Manufacturers Association.
- Bayerdörfer, I. (1997), Method to Assess the Wear Characteristics of Lubricants, FZG Test Method C/0.05/90:120/12, Germany: Deutsche Wissenschaftliche Gesellschaft für Erdöl, Erdgas und Kohle e.V.
- ISO 14635-1. (2000), Gears—FZG Test Procedures—Part 1: FZG Test Method A/8.3/90 for Relative Scuffing Load-Carrying Capacity of Oils, . Switzerland: ISO copyright office.
- Emmert, S. (1993), Testverfahren zur Untersuchung des Schmierstoffeinflusses auf die Entstehung von Grauflecken bei Zahnrädern . [Test method to investigate the lubricant influence on the micropitting load carrying capacity], Germany: Forschungsvereinigung für Antriebstechnik e.V.
- ISO 4288. (1996), Geometrical Product Specifications (GPS)—Surface Texture: Profile Method—Rules and Procedures for the Assessment of Surface Texture, . Switzerland: ISO copyright office.
- Hurley, S. and Cann, P.M. (2000), “Infrared Spectroscopic Characterisation of Grease Lubricant Films on Metal Surfaces,” NLGI Spokesman, 64, pp 360–377.
- Cann, P. and Spikes, H. (1992), “Film Thickness Measurements of Lubricating Greases under Normally Starved Conditions,” NLGI Spokesman, 56, pp 21–31.
- Farcas, F. and Gafitanu, M.D. (1999), “Some Influence Parameters on Grease Lubricated Rolling Contacts Service Life,” Wear, 47, pp 225–229.
- Kaneta, M., Ogata, T., Takubo, Y., and Naka, N. (2000), “Effects of a Thickener Structure on Grease Elastohydrodynamic Lubrication Films,” Journal of Engineering Tribology, 214(4), pp 45–52.
- Muennich, H.C. and Gloeckner, H.J. R. (1980), “Elastohydrodynamic Lubrication of Grease-Lubricated Rolling Bearings,” Tribology Transactions, 23(1), pp 45–52.
- Palacios, J.M. and Palacios, M.P. (1984), “Rheological Properties of Greases in EHD Contacts,” Tribology International, 17, pp 167–171.
- Wilson, A. (1979), “Relative Thickness of Grease and Oil Films in Rolling Bearings,” Proceedings of the Institution of Mechanical Engineers, 193, pp 185–192.
- Cann, P.M. (1999), “Starved Grease Lubrication of Rolling Contacts,” Tribology Transactions, 42(4), pp 867–873.
- Cousseau, T., Björling, M., Graça, B., Campos, A., Seabra, J., and Larsson, R. (2012), “Film Thickness in a Ball-on-Disc Contact Lubricated with Greases, Bleed Oils and Base Oils,” Tribology International, 53, pp 53–60.
- Lugt, P.M. (2009), “A Review on Grease Lubrication in Rolling Bearings,” Tribology Transactions, 52(4), pp 470–480.
- Höhn, B.-R., Michaelis, K., Oster, P., Schrade, U., and Tobie, T. (2005), “Calculation of the Micropitting Load Capacity of Case Carburized Gears,” COST 532 Conference Triboscience and Tribotechnology, Porto, Portugal, 12–14 October.
- Dowson, D. and Higginson, G.R. (1966), Elastohydrodynamic Lubrication, Oxford: Pergamon Press.
- Stemplinger, J.P., Stahl, K., Höhn, B.R., Michaelis, K., Otto, H.P., and Hochmann, M. (2012), Wear Behavior of Grease Lubricated Gears, . 24th ELGI Annual General Meeting 2012, 28 April–1 May, München, Germany.
- ISO 14635-3. (2005), Gears—FZG Test Procedures—Part 3: FZG Test Method A/2.8/50 for Relative Scuffing Load-Carrying Capacity and Wear Characteristics of Semi-Fluid Gear Greases.