References
- Sasaki, A., H. Aoyama, T. Honda, Y. Iwai, and C.K. Yong (2014), “A Study of the Colors of Contamination in Used Oils,” Tribology Transactions, 57(1), pp 1–10.
- Matsumoto, K., H. Watanabe, and N. Yoshida (2013), “A TEM Investigation of Crack Formation Mechanism on Chrome–Molybdenum Steel Tested under Real Driving Conditions,” Tribology Transactions, 56(6), pp 897–907.
- Fatima, N., P. Marklund, and R. Larsson (2013), “Influence of Clutch Output Shaft Inertia and Stiffness on the Performance of the Wet Clutch,” Tribology Transactions, 56(2), pp 310–319.
- Wang, J.M., Ch. Xu, J.H. Wang, Ch.Sh. Li, G.Q. Zhao, and X.B. Wang, (2013), “Tribological Properties of Three S-Alkyl-N,N-dicarboxymethyl Dithiocarbamates as Additives in Water–Glycol Hydraulic Fluid,” Tribology Transactions, 56(3), pp 374–384.
- Macián, V., B. Tormos, Y.A. Gómez, and J.M. Salavert (2102), “Proposal of an FTIR Methodology to Monitor Oxidation Level in Used Engine Oils: Effects of Thermal Degradation and Fuel Dilution,” Tribology Transactions, 55(6), pp 872–882.
- Ghosh, P., T. Das, and D. Nandi (2009), “Synthsis of Copoly-mers and Homopolymers of Methyl Methacrylate and Styrene and Studies on their Viscometric Properties in Three Differ-ent Solvents. Research,” Research Journal of Chemistry and Environment, 13(1), pp 17–25.
- Abdel-Azim, A.A. A., A.M. Nasser, N.S. Ahmed, A.F. E. I. Ka-frawy, and R.S. Kamal (2009), “Multifunctional Additives Viscosity Index Improvers, Pour Point Depressants and Dispersants for Lube Oil,” Petroleum Science and Technology, 27, pp 20–32.
- Ghosh, P., T. Das, and D. Nandi (2011), “Shear Stability and Thickening Properties of Homo and Copolymer of Methyl Methacrylate,” American Journal of Polymer Science, 1(1), pp 1–5.
- Holtzinger, J., J. Green, G. Lamb, D Atkinson, and H. Spikes (2012), “New Method of Measuring Permanent Viscosity Loss of Polymer-Containing Lubricants,” Tribology Transactions, 55(5), pp 631–639.
- Bair, S. and W.O. Winer (1979), “Shear Strength Measurements of Lubricants at High Pressure,” ASME Journal of Lubrication Technology, 101, pp 251–257.
- Höglund, E. and B. Jacobson (1986), “Experimental Investigation of the Shear Strength of Lubricants Subjected to High Pressure and Temperature,” Journal of Lubrication Technology, 108, pp 571–578.
- Kato, Y., T. Iwasaki, M. Kato, and K. Inoue (1992), “Evaluation of Limiting Shear Stress of Lubricants by Roller Test,” Transactions of Japan Society of Mechanical Engineers, Part C, 58(546), pp 558–564.
- Kinker, B. (1998), “Automatic Transmission Fluid Shear Stability Testing and Viscosity Index Improver Trends,” International Symposium on the Tribology of Vehicle Transmissions, Yokohamo.
- Mortier, R.M. and S.T. Qrszulik (1997), Chemistry and Technology of Lubricants Blackie Academic and Professiona: London.
- Santos, J.C. O., I.M. G. Dos Santos, A.G. Souza, E.V. Sobrin-ho, V.J. Jr. Fernandes, and A.J. N. Silva (2004), “Thermoanalytical and Rheological Characterization of Automotive Mineral Lubricants after Thermal Degradation,” Fuel, 83, pp 2393–2399.
- ASTM D6278-07. “Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus,” ASTM International.
- ASTM D5621-01. “Standard Test Method for Sonic Shear Stability of Hydraulic Fluid,” ASTM International.
- CEC L-45-A-99. “Viscosity Shear Stability of Transmission Lubricants (Taper Roller Bearing Rig),” ASTM International.
- ASTM D445. “Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity),” ASTM International.
- ASTM D7043-04. “Test Method for Indicating Wear Characteristics of Petroleum and Non-Petroleum Hydraulic Fluids in a Constant Volume Vane Pump,” ASTM International.