Effect of Sintering Temperature and Atmosphere on Nonlubricated Sliding Wear of Nano-Yttria-Dispersed and Yttria-Free Duplex and Ferritic Stainless Steel Fabricated by Powder Metallurgy

References

• Gupta, S., Shashanka, R., and Chaira, D. (2015), “Synthesis of Nano-Structured Duplex and Ferritic Stainless Steel Powders by Planetary Milling: An Experimental and Simulation Study,” IOP Conference Series: Materials Science and Engineering, 75, pp 012033.
   Google Scholar
• Herenu, S., Alvarez-Armas, I., and Armas, A. F. (2001), “The Influence of Dynamic Strain Ageing on the Low Cycle Fatigue of Duplex Stainless Steel,” Scripta Materialia, 45, pp 739–745.
   Web of Science ®Google Scholar
• Miyamoto, H., Mirnaki, T., and Hashimoto, S. (2001), “Super Plastic Deformation of Micro-Specimens of Duplex Stainless Steel,” Materials Science and Engineering A, 319, pp 779–783.
   Web of Science ®Google Scholar
• Shashanka, R., and Chaira, D. (2015), “Optimization of Milling Parameters for the Synthesis of Nano-Structured Duplex and Ferritic Stainless Steel Powders by High Energy Planetary Milling,” Powder Technology, 278, pp 35–45.
   Web of Science ®Google Scholar
• Karahan, T., Emre, H. E., Tumer, M., and Kacar, R. (2014), “Strengthening of AISI 2205 Duplex Stainless Steel by Strain Ageing,” Materials & Design, 55, pp 250–256.
   Web of Science ®Google Scholar
• Shashanka, R., and Chaira, D. (2015), “Development of Nano-Structured Duplex and Ferritic Stainless Steels by Pulverisette Planetary Milling Followed by Pressureless Sintering,” Materials Characterization, 99, pp 220–229.
   Web of Science ®Google Scholar
• Shashanka, R., and Chaira, D. (2014), “Phase Transformation and Microstructure Study of Nano-Structured Austenitic and Ferritic Stainless Steel Powders Prepared by Planetary Milling,” Powder Technology, 259, pp 125–136.
   Web of Science ®Google Scholar
• Phaniraj, M. P., Kim, D. I., Shim, J. H., and Cho, Y. W. (2010), “Cyclic Oxidation of Yttria Dispersed Austenitic Stainless Steels,” Corrosion Science, 52, pp 3573–3576.
   Web of Science ®Google Scholar
• Bautista, A., Velasco, F., and Abenojar, J. (2003), “Oxidation Resistance of Sintered Stainless Steels: Effect of Yttria Additions,” Corrosion Science, 45, pp 1343–1354.
   Web of Science ®Google Scholar
• Pivin, J. C., Delaunay, D., Roques-Carmes, C., Huntz, A. M., and Lacombe, P. (1980), “Oxidation Mechanism of Fe-Ni-20-25Cr-5Al Alloys—Influence of Small Amounts of Yttrium on Oxidation Kinetics and Oxide Adherence,” Corrosion Science, 20, pp 351–373.
   Web of Science ®Google Scholar
• Karak, S. K., Vishnu, C. S., Witczak, Z., Lojkowski, W., Majumdar, J. D., and Manna, I. (2010), “Studies on Wear Behavior of Nano-Y2O3 Dispersed Ferritic Steel Developed by Mechanical Alloying and Hot Isostatic Pressing,” Wear, 270, pp 5–11.
   Web of Science ®Google Scholar
• Li, C. X. (2010) Surface Engineering, Wear and Wear Mechanism, The University of Birmingham: Birmingham, UK.
   Google Scholar
• Hutchings, I. M. (1992), Tribology: Friction and Wear of Engineering Materials, Edward Arnold: London.
   Google Scholar
• Wei, X., Hua, M., Xue, Z., Gao, Z., and Li, J. (2009), “Evolution of Friction-Induced Microstructure of SUS 304 Meta-Stable Austenitic Stainless Steel and Its Influence on Wear Behaviour,” Wear, 267, pp 1386–1392.
   Web of Science ®Google Scholar
• Fargas, G., Mestra, A., and Mateo, A. (2013), “Effect of Sigma Phase on the Wear Behavior of a Super Duplex Stainless Steel,” Wear, 303, pp 584–590.
   Web of Science ®Google Scholar
• Kurgan, N., Yavuz, S., Bunyamin, C., and Hayrettin, A. (2012), “Production of 316L Stainless Steel Implant Materials by Powder Metallurgy and Investigation of Their Wear Properties,” Chinese Science Bulletin, 57, pp 1873–1878.
   Google Scholar
• Archard, J. F., and Hirst, W. (1956), “The Wear of Metals under Unlubricated Conditions,” Proceedings of the Royal Society of London A: Mathematical, Physical and Engineering Sciences, 236, pp 397–410.
   Web of Science ®Google Scholar
• Tiwari, S. M., Balaji, S., and Upadhyaya, A. (2008), “Sintering and Characterization of YAG Dispersed Ferritic Stainless Steels,” Materials Science and Engineering A, 492, pp 60–67.
   Web of Science ®Google Scholar
• Jain, J., Kar, A. M., and Upadhyaya, A. (2004), “Effect of YAG Addition on Sintering of P/M 316L and 434L Stainless Steels,” Materials Letters, 58, pp 2037–2040.
   Web of Science ®Google Scholar
• German, R. M. (1996), Sintering Theory and Practice, Wiley: New York.
   Google Scholar
• German, R. M. (1990), “Supersolidus Liquid Phase Sintering. I: Process Review,” International Journal of Powder Metallurgy, 26, pp 23–43.
   Web of Science ®Google Scholar
• Hwang, K. S., German, R. M., and Lenel, F. V. (1987), “Capillary Forces between Spheres during Agglomeration and Liquid Phase Sintering,” Metallurgical Transactions A, 18, pp 11–17.
   Web of Science ®Google Scholar
• Pandya, S., Ramakrishna, K. S., Annamalai, A. R., and Upadhyaya, A. (2012), “Effect of Sintering Temperature on the Mechanical and Electrochemical Properties of Austenitic Stainless Steel,” Materials Science and Engineering A, 556, pp 271–277.
   Web of Science ®Google Scholar
• Shashanka, R., and Chaira, D. (2015), “Effects of Nano-Y2O3 and Sintering Parameters on the Fabrication of PM Duplex and Ferritic Stainless Steels,” Acta Metallurgica Sinica (English Letters), 29(1), pp 58–71.
   Web of Science ®Google Scholar
• Kurgan, N. (2013), “Effects of Sintering Atmosphere on Microstructure and Mechanical Property of Sintered Powder Metallurgy 316L Stainless Steel,” Materials & Design, 52, pp 995–998.
   Web of Science ®Google Scholar
• Rawers, J. C., Tylczak, J. H., and Alman, D. E. (2008), “Wear Evaluation of High Interstitial Stainless Steels,” Tribology Transactions, 51, pp 515–525.
   Web of Science ®Google Scholar
• Abenojar, J., Velasco, F., Bautista, A., Campos, M., Bas, J. A., and Torralba, J. M. (2003), “Atmosphere Influence in Sintering Process of Stainless Steels Matrix Composites Reinforced with Hard Particles,” Composites Science and Technology, 63, pp 69–79.
   Web of Science ®Google Scholar
• Salahinejad, E., Amini, R., and Hadianfard, M. J. (2010), “Contribution of Nitrogen Concentration to Compressive Elastic Modulus of 18Cr-12Mn-xN Austenitic Stainless Steels Developed by Powder Metallurgy,” Materials & Design, 31, pp 2241–2244.
   Web of Science ®Google Scholar
• Lal, S., and Upadhyaya, G. S. (1989), “Oxidation Behavior of Sintered 316L Austenitic Stainless Steel–Yttria Composites with Various Additions,” Oxidation of Metals, 32, pp 317–335.
   Web of Science ®Google Scholar
• Chowdhury, M. A., Nuruzzaman, D. M., Roy, B. K., Dey, P. K., Mostafa, M. G., Islam, M. S., and Mia, M. R. (2013), “Experimental Investigation on Friction and Wear of Stainless Steel 304 Sliding against Different Pin Materials,” World Applied Sciences Journal, 22, pp 1702–1710.
   Google Scholar
• Farias, M. C. M., Souza, R. M., Sinatora, A., and Tanaka, D. K. (2007), “The Influence of Applied Load, Sliding Velocity and Martensitic Transformation on the Unlubricated Sliding Wear of Austenitic Stainless Steels,” Wear, 263, pp 773–781.
   Web of Science ®Google Scholar
• Stott, F. H. (1998), “The Role of Oxidation in the Wear of Alloys,” Tribology International, 31, pp 61–71.
   Web of Science ®Google Scholar
• Quinn, T. F. J. (1983), “Review of Oxidational Wear, Part 1: The Origins of Oxidational Wear,” Tribology International, 16, pp 257–271.
   Web of Science ®Google Scholar
• Jiang, J., Stott, F. H., and Stack, M. M. (1994), “Some Frictional Features Associated with the Sliding Wear of the Nickel-Base Alloy N80A at Temperatures to 250°C,” Wear, 176, pp 185–194.
   Web of Science ®Google Scholar
• Soydan, Y., Köksal, S., Demirer, A., and Çelik, V. (2008), “Sliding Friction and Wear Behaviour of Pack-Boronized AISI 1050, 4140, and 8620 Steels,” Tribology Transactions, 51, pp 74–81.
   Web of Science ®Google Scholar
• Khor, K. A., Wang, M., Zhou, W., Boey, F., and Srivatsan, T. S. (2001), Processing and Fabrication of Advanced Materials VIII, World Scientific: NTU Singapore.
   Google Scholar
• Acilar, M., and Gul, F. (2004), “Effect of the Applied Load, Sliding Distance and Oxidation on the Dry Sliding Wear Behaviour of Al-10Si/SiCp Composites Produced by Vacuum Infiltration Technique,” Materials & Design, 25, pp 209–217.
   Web of Science ®Google Scholar
• Wang, B., Yao, B., and Han, Z. (2012), “Annealing Effect on Wear Resistance of Nanostructured 316L Stainless Steel Subjected to Dynamic Plastic Deformation,” Journal of Materials Science & Technology, 28, pp 871–877.
   Web of Science ®Google Scholar
• Kim, H., Choi, J. H., Kim, J. K., Hong, H. S., and Kim, S. J. (2003), “Reciprocating Sliding Wear of Inconel 600 Tubing in Room Temperature Air,” Journal of Alloys and Compounds, 351, pp 309–313.
   Web of Science ®Google Scholar
• Wei, M. X., Wang, S. Q., Wang, L., and Cui, X. H. (2011), “Wear and Friction Characteristics of a Selected Stainless Steel,” Tribology Transactions, 54, pp 840–848.
   Web of Science ®Google Scholar