Investigations on Dry Sliding Wear Behavior of a Wire Arc Additively Manufactured Nickel-Based Superalloy

References

• Zhou, H., Wu, C., Tang, D.-y., Shi, X., Xue, Y., Huang, Q., Zhang, J., Elsheikh, A. H., and Ibrahim, A. M. M. (2021), “Tribological Performance of Gradient Ag–Multilayer Graphene/TC4 Alloy Self-Lubricating Composites Prepared by Laser Additive Manufacturing,” Tribology Transactions, 64(5), pp 819–829. doi:10.1080/10402004.2021.1922789
   Web of Science ®Google Scholar
• Navarro, M., Matar, A., Diltemiz, S. F., and Eshraghi, M. (2022), “Development of a Low-Cost Wire Arc Additive Manufacturing System,” Journal of Manufacturing and Materials Processing, 6(1), pp 1–14.
   Google Scholar
• Chigilipalli, B. K. and Veeramani, A. (2022), “Investigation of the Corrosion Behavior of Wire Arc Additively Manufactured Alloy 825,” Transactions of the Indian Institute of Metals, 2, pp 1–8. doi:10.1007/s12666-022-02656-9
   Google Scholar
• Wei, S. Z., Liu, Y., Zhang, G. S., Xu, L. J., Li, J. W., and Ren, Y. Y. (2015), “Microstructure and Wear Resistance of Fe-Cr-C Hardfacing Alloy Reinforced by Titanium Carbonitride,” Tribology Transactions, 58(4), pp 745–749. doi:10.1080/10402004.2014.1003119
   Web of Science ®Google Scholar
• Thakur, A., Gangopadhyay, S., Maity, K. P., and Sahoo, S. K. (2016), “Evaluation on Effectiveness of CVD and PVD Coated Tools during Dry Machining of Incoloy 825,” Tribology Transactions, 59(6), pp 1048–1058. doi:10.1080/10402004.2015.1131350
   Web of Science ®Google Scholar
• Chigilipalli, B. K. and Veeramani, A. (2022), “An Experimental Investigation and Neuro-Fuzzy Modeling to Ascertain Metal Deposition Parameters for the Wire Arc Additive Manufacturing of Incoloy 825,” CIRP Journal of Manufacturing Science and Technology, 38, pp 386–400. doi:10.1016/j.cirpj.2022.05.008
   Web of Science ®Google Scholar
• Sayiram, G. and Arivazhagan, N. (2015), “Microstructural Characterization of Dissimilar Welds between Incoloy 800H and 321 Austenitic Stainless Steel,” Materials Characterization, 102, pp 180–188. doi:10.1016/j.matchar.2015.03.006
   Web of Science ®Google Scholar
• Kangazian, J. and Shamanian, M. (2017), “Mechanical and Microstructural Evaluation of SAF 2507 and Incoloy 825 Dissimilar Welds,” Journal of Manufacturing Processes, 26, pp 407–418. doi:10.1016/j.jmapro.2017.03.006
   Web of Science ®Google Scholar
• Bharat Kumar, C. H. and Anandakrishnan, V. (2020), “Experimental Investigations on the Effect of Wire Arc Additive Manufacturing Process Parameters on the Layer Geometry of Inconel 825,” Materials Today: Proceedings, 21, pp 622–627.
   Google Scholar
• Alcisto, J., Enriquez, A., Garcia, H., Hinkson, S., Steelman, T., Silverman, E., Valdovino, P., Gigerenzer, H., Foyos, J., Ogren, J., Dorey, J., Karg, K., McDonald, T., and Es-Said, O. S. (2011), “Tensile Properties and Microstructures of Laser-Formed Ti-6Al-4V,” Journal of Materials Engineering and Performance, 20(2), pp 203–212. doi:10.1007/s11665-010-9670-9
   Web of Science ®Google Scholar
• Wang, Y., Chen, X., and Su, C. (2019), “Microstructure and Mechanical Properties of Inconel 625 Fabricated by Wire-Arc Additive Manufacturing,” Surface and Coatings Technology, 374, pp 116–123.
   Web of Science ®Google Scholar
• Panchagnula, J. S. and Simhambhatla, S. (2018), “Manufacture of Complex Thin-Walled Metallic Objects Using Weld-Deposition Based Additive Manufacturing,” Robotics and Computer-Integrated Manufacturing, 49(2017), pp 194–203. doi:10.1016/j.rcim.2017.06.003
   Google Scholar
• Ghaffari, M., Nemani, A. V., Nasiri, A. (2021), “Microstructure and Mechanical Behavior of PH 13–8Mo Martensitic Stainless Steel Fabricated by Wire Arc Additive Manufacturing,” Additive Manufacturing, 49, p 102374.
   Google Scholar
• Low, K. O., El-Tayeb, N. S. M., Brevern, P. V., and Chong, F. M. (2009), “Study on the Scratch Hardness and Indentation Hardness of Burnished Poly(oxymethylene) Surfaces,” Tribology Transactions, 52(2), pp 197–203. doi:10.1080/10402000802302490
   Web of Science ®Google Scholar
• Anandakrishnan, V., Sathish, S., Muthukannan, D., Dillibabu, V., and Balamuralikrishnan, N. (2020), “Dry Sliding Wear Behavior of Inconel 718 Additively Manufactured by DMLS Technique,” Industrial Lubrication and Tribology, 72(4), pp 491–496. doi:10.1108/ILT-08-2019-0322
   Web of Science ®Google Scholar
• Pradeep, G. V. K., Duraiselvam, M., and Sivaprasad, K. (2022), “Tribological Behavior of Laser Surface Melted γ-TiAl Fabricated by Electron Beam Additive Manufacturing,” Journal of Materials Engineering and Performance, 31(2), pp 1009–1020. doi:10.1007/s11665-021-06278-y
   Web of Science ®Google Scholar
• Haden, C. V., Zeng, G., Carter, F. M., Ruhl, C., Krick, B. A., and Harlow, D. G. (2017), “Wire and Arc Additive Manufactured Steel: Tensile and Wear Properties,” Additive Manufacturing, 16(2010), pp 115–123. doi:10.1016/j.addma.2017.05.010
   Google Scholar
• Mu, D., Shen, B. L., and Zhao, X. (2010), “Effects of Boronizing on Mechanical and Dry-Sliding Wear Properties of CoCrMo Alloy,” Materials and Design, 31(8), pp 3933–3936.
   Web of Science ®Google Scholar
• Evangeline, A. and Sathiya, P. (2019), “Cold Metal Arc Transfer (CMT) Metal Deposition of Inconel 625 Superalloy on 316L Austenitic Stainless Steel: Microstructural Evaluation, Corrosion and Wear Resistance Properties,” Materials Research Express, 6(6), pp 1–48. doi:10.1088/2053-1591/ab0a10
   Web of Science ®Google Scholar
• Amanov, A., Sasaki, S., Cho, I. S., Suzuki, Y., Kim, H. J., and Kim, D. E. (2013), “An Investigation of the Tribological and Nano-Scratch Behaviors of Fe-Ni-Cr Alloy Sintered by Direct Metal Laser Sintering,” Materials and Design, 47, pp 386–394. doi:10.1016/j.matdes.2012.11.062
   Web of Science ®Google Scholar
• Okonkwo, P. C., Kelly, G., Rolfe, B. F., and Pereira, M. P. (2016), “The Effect of Sliding Speed on the Wear of Steel–Tool Steel Pairs,” Tribology Internationa, 97, pp 218–227. doi:10.1016/j.triboint.2016.01.030
   Web of Science ®Google Scholar
• Pearson, S. R., Shipway, P. H., Abere, J. O., and Hewitt, R. A. A. (2013), “The Effect of Temperature on Wear and Friction of a High Strength Steel in Fretting,” Wear, 303(1–2), pp 622–631. doi:10.1016/j.wear.2013.03.048
   Web of Science ®Google Scholar
• Khajuria, G. and Wani, M. F. (2017), “High-Temperature Friction and Wear Studies of Nimonic 80A and Nimonic 90 against Nimonic 75 under Dry Sliding Conditions,” Tribology Letters, 65(3), pp 1–26. doi:10.1007/s11249-017-0881-1
   Web of Science ®Google Scholar
• Samuel, S. C., Arivarasu, M., and Prabhu, T. R. (2020), “High Temperature Dry Sliding Wear Behaviour of Laser Powder Bed Fused Inconel 718,” Additive Manufacturing, 34, p 101279. doi:10.1016/j.addma.2020.101279
   Web of Science ®Google Scholar
• Ashok Raj, J. and Kailas, S. V. (2020), “Evolution of Wear Debris Morphology during Dry Sliding of Ti–6Al–4V against SS316L under Ambient and Vacuum Conditions,” Wear, 456–457, pp 8–10. doi:10.1016/j.wear.2020.203378
   Web of Science ®Google Scholar
• Duraisamy, R., Kumar, S. M., Kannan, A. R., Shanmugam, N. S., Sankaranarayanasamy, K., and Ramesh, M. R. (2020), “Tribological Performance of Wire Arc Additive Manufactured 347 Austenitic Stainless Steel under Unlubricated Conditions at Elevated Temperatures,” Journal of Manufacturing Processes, 56, pp 306–321. doi:10.1016/j.jmapro.2020.04.073
   Web of Science ®Google Scholar
• Parvaresh, B., Salehan, R., and Miresmaeili, R. (2021), “Investigating Isotropy of Mechanical and Wear Properties in As-Deposited and Inter-Layer Cold Worked Specimens Manufactured by Wire Arc Additive Manufacturing,” Metals and Materials International, 27(1), pp 92–105. doi:10.1007/s12540-020-00793-8
   Web of Science ®Google Scholar
• Saroj, S., Sahu, A., and Masanta, M. (2020), “Geometrical Assessment and Mechanical Characterization of Single-Line Inconel 825 Layer Fabricated on AISI 304 Steel by TIG Cladding Method,” Surfaces and Interfaces, 20, p 100631. doi:10.1016/j.surfin.2020.100631
   Web of Science ®Google Scholar
• Hutchings, I. and Shipway, P. (2017), Tribology: Friction and Wear of Engineering Materials, Butterworth-Heinemann, Elsevier Science: Amsterdam, Netherlands.
   Google Scholar
• Kumar, M. R., Kumar, H., Harmain, G. A., and Albert, S. K. (2022), “Wear Performance of Ni-Cr-B-Si Hardface Coatings Fabricated by Cold Metal Transfer Welding,” Proceedings of Institution of Mechanical Engineers - Part C: Journal of Mechanical Engineering Science, 236(3), pp 1850–60. doi:10.1177/09544062211023085
   Web of Science ®Google Scholar
• Halil Aytekin, Y. A. (2013), “Characterization of Borided Incoloy 825 Alloy,” Materials and Design, 50, pp 515–521. doi:10.1016/j.matdes.2013.03.015
   Web of Science ®Google Scholar
• Kangazian, J. and Shamanian, M. (2018), “Characterization of Structure–Property Relationship of Incoloy 825 and SAF 2507 Dissimilar Welds,” Transactions of the Indian Institute of Metals, 71(7), pp 1747–1757. doi:10.1007/s12666-018-1309-9
   Web of Science ®Google Scholar
• Lin, J. W. and Chang, H. C. (2011), “Measurement of Friction Surface and Wear Rate between a Carbon Graphite Brush and a Copper Ring,” Tribology Transactions, 54(6), pp 887–894. doi:10.1080/10402004.2011.613555
   Web of Science ®Google Scholar
• Wilson, A. S., Christofidou, K. A., Evans, A., Hardy, M. C., and Stone, H. J. (2019), “Comparison of Methods for Quantification of Topologically Close-Packed Phases in Ni-Based Superalloys,” Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 50(12), pp 5925–5934. doi:10.1007/s11661-019-05442-3
   Web of Science ®Google Scholar
• Murr, L. E., Martinez, E., Gaytan, S. M., Ramirez, D. A., MacHado, B. I., Shindo, P. W., Martinez, J. L., Medina, F., Wooten, J., Ciscel, D., Ackelid, U., and Wicker, R. B. (2011), “Microstructural Architecture, Microstructures, and Mechanical Properties for a Nickel-Base Superalloy Fabricated by Electron Beam Melting,” Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 42(11), pp 3491–3508. doi:10.1007/s11661-011-0748-2
   Google Scholar
• Jiang, Q., Zhang, P., Yu, Z., Shi, H., Li, S., Wu, D., Yan, H., Ye, X., and Chen, J. (2021), “Microstructure and Mechanical Properties of Thick-Walled Inconel 625 Alloy Manufactured by Wire Arc Additive Manufacture with Different Torch Paths,” Advanced Engineering Materials, 23(1), pp 1–13. doi:10.1002/adem.202000728
   Web of Science ®Google Scholar
• Naga Krishna, N., Tejas, R., Sivaprasad, K., and Venkateswarlu, K. (2013), “Study on Cryorolled Al-Cu Alloy Using X-ray Diffraction Line Profile Analysis and Evaluation of Strengthening Mechanisms,” Materials and Design, 52, pp 785–790. doi:10.1016/j.matdes.2013.05.095
   Web of Science ®Google Scholar
• Langford, J. and W, A. J. (1978), “Seherrer after Sixty Years: A Survey and Some New Results in the Determination of Crystallite Size,” Journal of Applied Crystallography, 11(2), pp 102–113. doi:10.1107/S0021889878012844
   Google Scholar
• Vignesh, G., Pandivelan, C., and Sathiya Narayanan, C. (2019), “Study on Formability and Dislocation Density in Forming of Hemispherical Cup,” Materials Today: Proceedings, 27, pp 2005–2010.
   Google Scholar
• Chi, J., Cai, Z., Wan, Z., Zhang, H., Chen, Z., Li, L., Li, Y., Peng, P., and Guo, W. (2020), “Effects of Heat Treatment Combined with Laser Shock Peening on Wire and Arc Additive Manufactured Ti17 Titanium Alloy: Microstructures, Residual Stress and Mechanical Properties,” Surface and Coatings Technology, 396, p 125908.
   Web of Science ®Google Scholar
• Raymond, E. (1968), “Mechanisms of Sensitization and Stablization of Incoloy Nickel–Iron–Chromium Alloy 825,” Corrosion, 24(6), pp 180–188. doi:10.5006/0010-9312-24.6.180
   Web of Science ®Google Scholar
• Ren, Q., Cui, G., Li, T., Hassani, M., Liu, Y., and Kou, Z. (2021), “High-Temperature Wear Behavior of Cobalt Matrix Composites Reinforced by LaF3 and CeO2,” Tribology Letters, 69(4), pp 1–11. doi:10.1007/s11249-021-01524-9
   Web of Science ®Google Scholar
• Archard, J. F. (1953), “Contact and Rubbing of Flat Surfaces,” Journal of Applied Physics, 24(8), pp 981–988. doi:10.1063/1.1721448
   Web of Science ®Google Scholar
• Shah, N., Arora, K., Dhokey, N. B., Dileep Kumar, N., and Tharian, K. T. (2019), “Optimization of Cryogenic Process for Enhancing the Wear Resistance of Novel HNMS Steel for Cryogenic Bearings of Launch Vehicle,” Tribology Transactions, 62(4), pp 712–723. doi:10.1080/10402004.2019.1609147
   Web of Science ®Google Scholar
• Bhushan, B. (1999), Principles and Applications of Tribology, John Wiley & Sons: New Jersey, United States.
   Google Scholar
• Blau, P. J. (1992), “Scale Effects in Sliding Friction: An Experimental Study,” Fundamentals of Friction: Macroscopic and Microscopic Processes, pp 523–534, Springer: New York City, United States.
   Google Scholar
• Yi, H. J., Kim, J. W., Kim, Y. L., and Shin, S. (2020), “Effects of Cooling Rate on the Microstructure and Tensile Properties of Wire-Arc Additive Manufactured Ti-6Al-4V Alloy,” Metals and Materials International, 26(8), pp 1235–1246. doi:10.1007/s12540-019-00563-1
   Web of Science ®Google Scholar
• Suh, N. P. (1977), “An Overview of the Delamination Theory of Wear,” Wear, 44(1), pp 1–16. doi:10.1016/0043-1648(77)90081-3
   Web of Science ®Google Scholar
• Al-Maliki, H., Meierhofer, A., Trummer, G., Lewis, R., and Six, K. (2021), “A New Approach for Modelling Mild and Severe Wear in Wheel–Rail Contacts,” Wear, 476, pp 1–10.
   Web of Science ®Google Scholar
• Pradeep, G. V. K., Duraiselvam, M., Prasad, K. S., and Mohammad, A. (2020), “Tribological Behavior of Additive Manufactured γ-TiAl by Electron Beam Melting,” Transactions of Indian Institution of Metals, 73(6), pp 1661–1667.
   Web of Science ®Google Scholar